schmersal MZM 100 B ST2-1P2PW2REM-A-2930-DU Operating instructions

MZM 100 B ST2-1P2PW2REM-A-2930-DU
schmersal
Brand
schmersal
Model
MZM 100 B ST2-1P2PW2REM-A-2930-DU
Type
Operating instructions

This manual is also suitable for

The schmersal MZM 100 B ST2-1P2PW2REM-A-2930-DU is a safety switch with interlocking function, specifically designed for process protection. It features solenoid control for enabling safety outputs, eliminating the 10-minute tampering protection delay after forcible interruption of the safety switch and actuator. The diagnostic function provides visual LED indicators, serial status signals, and safety outputs for monitoring system conditions. It also has a latching force version (-R/-RE) that checks if the clamping force is reached, allowing the door to be locked.

The schmersal MZM 100 B ST2-1P2PW2REM-A-2930-DU is a safety switch with interlocking function, specifically designed for process protection. It features solenoid control for enabling safety outputs, eliminating the 10-minute tampering protection delay after forcible interruption of the safety switch and actuator. The diagnostic function provides visual LED indicators, serial status signals, and safety outputs for monitoring system conditions. It also has a latching force version (-R/-RE) that checks if the clamping force is reached, allowing the door to be locked.

MZM 100 B-…-2930
Operating Instructions - Supplementary Sheet
Safety switch with interlocking function
EN 1
Product description
The safety switches with interlock function MZM 100 B-…-2930 are a
special version for process protection. The differences compared to the
standard device MZM 100 - B are described below.
Unlike MZM 100 B, the special version MZM 100 B-…-2930 only enable
the safety outputs through triggering of the solenoid control (IN).
There is no time of the tampering protection of 10 minutes after forcible
interruption of safety switch and actuator.
About this document
These operating instructions serve as a supplement to the operating
instructions for MZM 100 / MZM 100 B. Deviating or additional
instructions follow.
Diagnostic function of variant MZM 100 B-ST.-1P2P...-2930
System condition Solenoid control LED Safety outputs Diagnostic output OUT
IN green red yellow Y1, Y2 -1P2PW / -1P2PW2 3)
Safety guard open 0 V On Off Off 0 V 0 V
Safety guard closed, actuator in 0 V On Off Flashes 0 V 24 V
Safety guard closed and locked 24 V On Off On 24 V 24 V
Solenoid interlock cannot be
locked. Safety guard not correctly
closed or magnet soiled
24 V On Off Flashes 0 V 0 V
Error warning1),
Safety guard locked
24 V On Flashes 2) On 24 V 0 V
Error 0 V / 24 V On Flashes 2) Off 0 V 0 V
Function of the visual diagnostic LED's, the serial status signals and the safety outputs
of the MZM 100 B-ST.-SD2P...-2930 by means of an example
System condition LED Safety outputs Response byte bit n°:
green red yellow Y1, Y2 7 6 5 4 3 2 1 0
Safety guard open On Off Off 0 V 0 0 0 X 0 0 0 0
Safety guard closed, actuator in On Off Flashes 0 V 0 0 0 X 0 0 1 0
Safety guard closed and locked On Off On 24 V 0 0 0 X 0 1 1 1
Solenoid interlock cannot be locked. Safety
guard not correctly closed or magnet soiled On Off Flashes 0 V 0 0 0 X 0 0 0/14) 0
Error warning1), Safety guard locked On Flashes 2) On 24 V 0 1 0 X 0 1 1 1
Error On Flashes 2) Off 0 V 1 0 0 X 0 X X 0
1) after 30 min -> fault
2) refer to flash code
3) -1P2PW2: Version with latching force -R/-RE checks if clamping force can be reached (door can be locked)
4) Version with latching force -R/-RE: Bit 1 = 0
Version without latching force: Bit 1 = 1
x.000 / 08.2016 / v.A. - 103013881-EN / A / 2016-08-09 / AE-Nr. -
K. A. Schmersal GmbH & Co. KG
Möddinghofe 30, D - 42279 Wuppertal
Postfach 24 02 63, D - 42232 Wuppertal
Phone: +49 - (0)2 02 - 64 74 - 0
Telefax: +49 - (0)2 02 - 64 74 - 1 00
E-Mail: [email protected]
Internet: http://www.schmersal.com
EN Operating instructions. . . . . . . . . . . . . . . . . page 1
Original
  • Page 1 1

schmersal MZM 100 B ST2-1P2PW2REM-A-2930-DU Operating instructions

MZM 100 B ST2-1P2PW2REM-A-2930-DU
schmersal
Brand
schmersal
Model
MZM 100 B ST2-1P2PW2REM-A-2930-DU
Type
Operating instructions
This manual is also suitable for

The schmersal MZM 100 B ST2-1P2PW2REM-A-2930-DU is a safety switch with interlocking function, specifically designed for process protection. It features solenoid control for enabling safety outputs, eliminating the 10-minute tampering protection delay after forcible interruption of the safety switch and actuator. The diagnostic function provides visual LED indicators, serial status signals, and safety outputs for monitoring system conditions. It also has a latching force version (-R/-RE) that checks if the clamping force is reached, allowing the door to be locked.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents