2. Metra
  3. 99-3051
99-3051

Metra 99-3051 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Metra 99-3051 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
1-800-221-0932 • www.metraonline.com
COPYRIGHT© 2002 METRA ELECTRONICS CORPORATION
INSTALLATION INSTRUCTIONS
Chevrolet Corvette 1990-96
VEHICLE APPLICATIONS
KIT FEATURES
• ISO head unit
provision with pocket
• Stacked ISO head
unit provision
• Double DIN head
unit provision
99-3051
Questions?
Call the Help Line: (800)253 TECH
Monday - Friday 9:00 am - 7:00 pm EST
Saturday - Sunday 10:00 am - 4:00 pm EST
INST993051
rev. 221102
Pocket
Tr implate
KIT COMPONENTS
Pocket
TOOLS REQUIRED
Brackets
(4) #6 x 1/4" Phillips
Flat Head Screws
Phillips
screw driver
Dremel
(2) #8 x 3/8" Phillips
Pan Head Screws
• Dash Disassembly 1
• Kit Features
• ISO Head Unit Provision with Pocket Assembly 2
• Double DIN Head Unit Provision Assembly 3
• Stacked ISO Head Unit Provision Assembly 4
• Final Assembly 5
TABLE OF CONTENTS
99-3051
Disconnect the negative
battery terminal to prevent an
accidental short circuit.
Remove (2) screws from A/C
vents and remove vents.
See figure A
Lift corners of carpet in center
console and remove (2) screws.
Remove navigation switch
panel/switch mask, exposing (2)
screws on top of radio brackets.
Remove rubber inserts in cup
holders and remove screws.
See figure B
Set parking brake and shifter
selector to drive.
Lift center console up and back.
See figure C
Remove (3) screws from radio
bezel and remove.
Remove (2) screws located on
sides of console to gain access
to radio screws.
Remove (4) screws attaching
radio to dash and remove
carefully.
* Remove obstruction from rear of
dash cavity as shown in figure D
1
2
3
4
5
6
7
DASH DISASSEMBLY
1
99-3051
99-3051 • Chevrolet Corvette 1990-96
B
9
8
A
D
C
Attach the Pocket Trimplate to
Pocket using (2) #8 x 3/8"
Phillips Pan Head
Screws provided.
See figure A
Align the holes in upper mounting
position of the Brackets to the
holes in the side of the head unit.
Use screws provided with head
unit to secure the Brackets.
See figure B
1
3
Place pocket assembly between
Brackets beneath radio.
4
Align the mounting holes and
secure pocket assembly to
Brackets using (4) #6 x 1/4"
Phillips Flat Head
Screws provided.
See figure C
5
2
99-3051 • Chevrolet Corvette 1990-96
A
B
C
ISO HEAD UNIT PROVISION WITH POCKET
2
99-3051
DOUBLE DIN HEAD UNIT PROVISION
99-3051 • Chevrolet Corvette 1990-96
3
Place left Bracket on head
unit(s), align holes and secure
using screws provided with
head unit(s).
See figure A
1
Repeat sequence on right side.
2
A
99-3051
Note: Metra recommends mounting
the pocket trimplate with the widest
border surface at the top.
99-3051 • Chevrolet Corvette 1990-96
STACKED ISO HEAD UNIT PROVISION
4
99-3051
FINAL ASSEMBLY
99-3051 • Chevrolet Corvette 1990-96
5
99-3051
A
Locate the factory wiring harness in the
dash. Metra recommends using the proper
mating adapter and making connections
as shown. (Isolate and individually tape
off the ends of any unused wires to
prevent electrical short circuit.)
See figure A
Re-connect the battery terminal and test
the unit for proper operation.
Reassemble dash in the reverse order of
the Dash Disassembly on page 1.
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
1
2
Mount radio and housing assembly into
dash opening using the (4) screws
removed during disassembly.
3
4
Place left Bracket on head
unit(s), align holes and secure
using screws provided with
head unit(s).
See figure A
Repeat sequence on right side.
A
1
2
/