Zenith C13A03D User manual

Brand: Zenith

Model: C13A03D

Type: User manual

This manual is also suitable for

H32G47DT

RECORD YOUR MODEL NUMBER

The model and serial number of the Destination

II PC/TV are

located on the back of the TV cabinet. For your future

convenience, we suggest that you record these numbers here:

MODEL NO.____________________________________

SERIAL NO.____________________________________

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.

REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence

of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a

risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating

and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

This product is equipped with a 3-wire grounding-type alternating current line plug. This plug will fit into the power

outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, contact your

electrician to replace your obsolete outlet. Do not defeat the safety purpose of the three-wire ground type plug.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code

(U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be

connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equip-

ment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio com-

munications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the

user may be required to correct the interference at his own expense.

CAUTION:

Do not attempt to modify this product in any way without written authorization from Gateway, Inc.

Unauthorized modification could void the user’s authority to operate this product.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

3-WIRE COMM-WARN B-3/99

Destination

II PC/TV is a trademark of Gateway, Inc.

PAGE 3

206-3489-O 3-WIRE GRND

1. Read Instructions

All the safety and operating instructions should be read

before the product is operated.

2. Follow Instructions

All operating and use instructions should be followed.

3. Retain Instructions

The safety and operating instructions should be retained for

future reference.

4. Heed Warnings

All warnings on the product and in the operating instruc-

tions should be adhered to.

5. Cleaning

Unplug this product from the wall outlet before cleaning.

Do not use liquid cleaners or aerosol cleaners. Use a damp

cloth for cleaning.

6. Water and Moisture

Do not use this product near water for example, near a

bath tub, wash bowl, kitchen sink, or laundry tub, in a wet

basement, or near a swimming pool.

7. Accessories

Do not place this product on an unstable cart, stand, tri-

pod, bracket, or table. The product may fall, causing serious

injury to a child or adult, and serious damage to the prod-

uct. Use only with a cart, stand, tripod, bracket, or table

recommended by the manufacturer, or sold with the prod-

uct. Any mounting of the product should follow the manu-

facturer’s instructions, and should use a mounting accesso-

ry recommended by the manufacturer.

8. Transporting Product

A product and cart combination should be moved with care.

Quick stops, excessive force, and uneven surfaces may

cause the product and cart combination to overturn.

9. Attachments

Do not use attachments not recommended by the product

manufacturer as they may cause hazards.

10. Ventilation

Slots and openings in the cabinet are provided for ventila-

tion and to ensure reliable operation of the product and to

protect it from overheating, and these openings must not

be blocked or covered. The openings should never be

blocked by placing the product on a bed, sofa, rug, or

other similar surface. This product should not be placed in

a built-in installation such as a bookcase or rack unless

proper ventilation is provided or the manufacturer’s instruc-

tions have been adhered to.

11. Power Sources

This product should be operated only from the type of

power source indicated on the marking label. If you are not

sure of the type of power supply to your home, consult

your product dealer or local power company. For products

intended to operate from battery power, or other sources,

refer to the operating instructions.

12. Line-Cord Polarization

This product is equipped with a 3-wire grounding type

alternating-current line plug. This plug will fit into the

power outlet only one way. This is a safety feature. If you

are unable to insert the plug fully into the outlet, contact

your electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the three-wire ground-type

plug.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not

likely to be walked on or pinched by items placed upon or

against them, paying particular attention to cords at plugs,

convenience receptacles, and the point where they exit

from the product.

IMPORTANT SAFETY INSTRUCTIONS

Important safeguards for you and your new product

Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential

electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read

and observe the following safety points when installing and using your new product, and save them for future reference.

Observing the simple precautions discussed in this operating guide can help you get many years of enjoyment and safe

operation that are built into your new product.

This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.

PORTABLE CART WARNING

(Continued on next page)

(Continued from previous page)

14. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the

product, be sure the antenna or cable system is grounded so

as to provide some protection against voltage surges and

built-up static charges. Article 810 of the National Electrical

Code (U.S.A.), ANSI/ NFPA 70 provides information with

regard to proper grounding of the mast and supporting

structure, grounding of the lead-in wire to an antenna dis-

charge unit, size of grounding conductors, location of

antenna-discharge unit, connection to grounding electrodes,

and requirements for the grounding electrode.

15. Lightning

For added protection for this product (receiver) during a

lightning storm, or when it is left unattended and unused

for long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line

surges.

16. Power Lines

An outside antenna system should not be located in the

vicinity of overhead power lines or other electric light or

power circuits, or where it can fall into such power lines or

circuits. When installing an outside antenna system,

extreme care should be taken to keep from touching such

power lines or circuits as contact with them might be fatal.

17. Overloading

Do not overload wall outlets and extension cords as this can

result in a risk of fire or electric shock.

18. Object and Liquid Entry

Never push objects of any kind into this product through

openings as they may touch dangerous voltage points or

short-out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the product.

19. Servicing

Do not attempt to service this product yourself as opening

or removing covers may expose you to dangerous voltage or

other hazards. Refer all servicing to qualified service person-

nel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing

to qualified service personnel under the following condi-

tions:

a. If the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into the

product.

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following

the operating instructions. Adjust only those controls that

are covered by the operating instructions as an improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the product to its normal operation.

e. If the product has been dropped or the cabinet has been

damaged.

f. If the product exhibits a distinct change in performance.

21. Replacement Parts

When replacement parts are required, be sure the service

technician has used replacement parts specified by the man-

ufacturer or have the same characteristics as the original

part. Unauthorized substitutions may result in fire, electric

shock, or other hazards.

22. Safety Check

Upon completion of any service or repairs to this product,

ask the service technician to perform safety checks to deter-

mine that the product is in proper operating condition.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as

recommended by the manufacturer.

24. Heat

The product should be situated away from heat sources such

as radiators, heat registers, stoves, or other products

(including amplifiers) that produce heat.

PAGE 4

206-3489-O

IMPORTANT SAFETY INSTRUCTIONS

Antenna Lead in Wire

Antenna Discharge Unit

(NEC Section 810-20)

Grounding Conductor

(NEC Section 810-21)

Ground Clamps

Power Service Grounding

Electrode System (NEC

Art 250, Part H)

Ground Clamp

Electric Service

Equipment

Example of Grounding According to National Electrical

Code Instructions

NEC - National Electrical Code

206-3643

PAGE 5

Table of Contents

This operating and installation guide is divided into three sections:

6 thru 13, Computer Section - Setting up the Destination II PC/TV to be used as a computer monitor.

14 thru 43, TV Section - Setting up the TV’s features.

44 thru 46, Installer section - A special section with information and instructions primarily used by

qualified electronics servicer/technicians to configure or adjust the operational features of this TV.

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Important Safety Information . . . . . . . . . . . . . . . . 3 - 4

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Optional: Computer Setups

Using the Destination II PC/TV as a Computer Monitor

Overview: Computer Monitor Setup . . . . . . . . . . . . . 6

Computer Hookup . . . . . . . . . . . . . . . . . . . . . 7 - 8

Video/S-Video Loop-out Setups . . . . . . . . . . . . . . . 9

Windows Environment Image Enhancements . . . . . . 10

Windows Troubleshooting . . . . . . . . . . . . . . . . . . 11

Computer Mode Remote Key Command Functions 12 - 13

Step 1. TV Connections

TV/VCR/Cable Box/Computer and other Equipment Hookup

TV Hookup Directory . . . . . . . . . . . . . . . . . . . . . . . . 14

Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Cable service . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Antenna with VCR . . . . . . . . . . . . . . . . . . . . . . . 17

Cable service with VCR . . . . . . . . . . . . . . . . . . . . 18

S-VHS VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

External Amplifier (Audio Out Hookups) . . . . . . . . . 20

Step 2. TV Reception Setup & Channel Search

Auto Program: Select Antenna, or Cable service

and do a channel search . . . . . . . . . . . . . . . . . . . 21

Front Panel Controls/Inputs . . . . . . . . . . . . . . . . . . . 22

Remote Control Key Functions in TV mode . . . . . . . . . . 23

On-Screen Menus Overview . . . . . . . . . . . . . . . . . . . . 24

Step 3. Customize the Destination II PC/TV’s

Features

Setup Menu (Start with page 21, Auto Program)

Add/Del/Blank . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Channel Labels (Preset and Custom) . . . . . . . . 26 - 27

Clock Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Closed Captions/Text menu . . . . . . . . . . . . . . . . . . 29

Alarm (Set a TV Automatic Turn-on Time) . . . . . . . . 30

Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Audio Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Video Menu/Computer Video Menu . . . . . . . . . . . . . 33

Parental Control Menu . . . . . . . . . . . . . . . . . . . 34 - 35

Other Menus and On-Screen Displays

Source menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Channel/Time/Audio Display . . . . . . . . . . . . . . . . . 36

Alarm menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Sleep Timer menu . . . . . . . . . . . . . . . . . . . . . . . . 36

Volume Display . . . . . . . . . . . . . . . . . . . . . . . . . 36

Closed Captions/Text menu . . . . . . . . . . . . . . . . . . 36

Ch Preview menu . . . . . . . . . . . . . . . . . . . . . . . . 36

Remote Control Programming to Control Other Products

Remote Control Programming . . . . . . . . . . . . . . . . 37

Amplifier Volume Override . . . . . . . . . . . . . . . . . . 38

Aux 1, Aux 2, Aux 3 Programming . . . . . . . . . . . . . 39

AutoFind . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Programming Product Name Brand Codes . . . . . . 41 - 42

Remote Modes (TV, Cable, VCR, Aux) Key Functions . . 43

Installer/Service Information

Note: This information is provided for techni-

cally qualified service personnel only. Settings

should not be changed by the average user!

Installer Menus . . . . . . . . . . . . . . . . . . . . . 44 - 45 - 46

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 47 - 48

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Destination II PC/TV Warranty

206-3602

PAGE 6

Connect your Computer to the TV using the cable provided

in the accessory packet supplied with the TV, follow the

hookup instructions on pages 7 and 8.

PC You can make a direct hookup to the TV’s front or

rear computer connectors without using any adapters.

MAC Macintosh configurations are not supported by

Gateway.

Video Mirror Connections (Optional)

The computer image can be sent to both the TV screen and

a computer monitor at the same time by using the video

mirror connection, follow the instructions on page 8.

PC Direct connection to the TV’s connectors using the

cable provided in the accessory packet.

MAC Macintosh configurations are not supported by

Gateway.

Adjust the Computer Display Output to the Destination

II PC/TV Requirements

PC If you connect your computer to the Rear “default

connection” Port, it supports both the optimum

800 x 600 @ 60 Hz computer display output settings

as well as other resolutions and refresh rates.

If you connect your computer to the Front Port on the

Destination II PC/TV, set your Computer display

output settings to SVGA 800 x 600 @ 60 Hz.

Set Up the Destination II TV for Computer Requirements

PC If your Computer is hooked up to the TV’s rear

computer port (default connection port), choose the

REAR COMPUTER SVGA source by pressing TV/VCR

SOURCE repeatedly on the remote control to select it

and then press ENTER. (The default computer source

setting is Rear Computer SVGA.)

If your Computer is hooked up to the TV’s front

computer port (800 x 600 @60 Hz), choose

the FRONT COMPUTER SVGA source by pressing TV/VCR

SOURCE repeatedly on the remote control to select it

and then press ENTER.

Additional Computer Image Enhancements (Optional)

Additional computer output adjustments to optimize the

computer image quality appearing on the TV screen.

PC See page 10 for Windows environment.

Troubleshooting

Problems? See troubleshooting on page 11 for PC

Computer/TV problems.

Notes

• Avoid using hookup cables of excessive length (longer

than 25 feet). Long cables can adversely affect image

quality and Computer/TV performance.

• Not all computer cables will work with the Destination II

PC/TV. Special extension cables are available from Gateway.

Overview: Computer Monitor Setup

Read the following overview/instructions to set up your Destination II PC/TV as a Computer Monitor

Using Your Destination II TV as a Computer Monitor (pages 6 - 13)

206-3643

PAGE 7

Make the basic connections as shown.

Plug in your TV. Do not plug it into a

switched outlet. Your Destination II PC/TV

is designed to operate on standard current,

120-volt 60 Hertz AC. Do not attempt to

operate it on DC Current.

Using the remote, choose the computer as

the viewing source. Press TV/VCR SOURCE

repeatedly until “REAR COMPUTER SVGA”

(Rear Computer in) is shown on the TV

screen, or “FRONT COMPUTER SVGA” (Front

Computer in) is shown on the TV screen.

Boot up your computer. As it warms up

the TV will adapt to your computer.

Computer Hook Up

The Destination II PC/TV is configured with the default com-

puter connection being the rear computer input. This connec-

tion offers the most resolution options and refresh rates.

(The default computer source is Rear Computer SVGA.)

For convenience, a front computer input jack is also provid-

ed. However, to use it, the computer display output must be

set to the optimum setting SVGA 800 x 600 @ 60Hz. Specify

FRONT COMPUTER SVGA in the Source menu or press TV/VCR

SOURCE repeatedly to select it, then press ENTER. If using

the front computer input, no picture will appear on the

screen until Windows has started.

Components may vary from those in the illustration.

On some notebook models you must locate the “display tog-

gle key” and switch the display to “external.” Refer to the

instructions for your computer.

Here is the basic setup to use the Destination II PC/TV as a computer monitor.

The default computer connection setup is to the rear computer input jack,

with the default computer source Rear Computer SVGA.

Back of

Computer

Video Out to

Computer

Monitor

"Video Mirror"

Cable

Computer Video "Card" Output

Computer Sound

"Card" Output

L audio R

video in

Connections to TV front or rear computer port,

with computer sound card output

to front or rear R - Audio - L inputs.

TV front

VIDEO

ANTENNA

CABLE

R- AUDIO- L

S-VIDEO IN

COMPUTER

AUDIO

AUX IN

M.P.I.

TV back

R- AUDIO- L

S-VIDEO OUT

AUDIO OUT

Video Out

206-3643

PAGE 8

An accessory packet is included with all models. A 15-ft. cable with a “video mirror” is featured for

providing a computer image to two monitors—an additional monitor and your Destination II PC/TV.

Computer monitor

Video cable

from monitor

Actual appearance

of components

may vary

Cable for

"video mirror"

Back of

computer

VIDEO

ANTENNA

CABLE

R- AUDIO- L

S-VIDEO IN

COMPUTER

AUDIO

AUX IN

M.P.I.

TV back

R- AUDIO- L

S-VIDEO OUT

AUDIO OUT

Video Out

Make the connections with the 15-ft. “video-mirror” cable as

shown. Also refer to the preceding page for audio connections

and “Using the monitor function.”

Your TV must be plugged in—not necessarily turned

on—for the computer monitor to function.

You can ”Daisy Chain” up to 4 other TVs via S-video

loop out and see the computer display on more TV

sets (see next page for set up instructions).

Computer Hook Up

L audio R

video in

(800 x 600 @60 Hz)

206-3643

PAGE 9

Computer, PC/TV Loop-Out Setups

Video cable

from monitor

Actual

appearance of

components

may vary

Cable for

"video mirror"

Back of computer

Master TV's Computer

output to other TVs

in the "Daisy Chain"

Computer Monitor

Computer

ABC

Computer

input to

Master TV

ABC

VIDEO

ANTENNA

CABLE

R- AUDIO- L

S-VIDEO IN

COMPUTER

AUDIO

AUX IN

M.P.I.

TV back

R- AUDIO- L

S-VIDEO OUT

AUDIO OUT

Video Out

Setup for Looping-Out S-Video/Video

Computer Image to a Master TV & other TVs

1. With the Computer and Destination II PC/TV

disconnected from power, make S-Video or

Video connections as shown.

2. Connect Computer and TV(s) to power, first

turn on the PC/TV, TVs, and then the Computer.

3. On the Destination II PC/TV, select TV

source “REAR COMPUTER NTSC OUT” using the

TV’s Source menu.

4. On the Computer, set display image to 800 x

600 @ 60Hz or SVGA.

5. On the Daisy-chained TVs, select the S-Video

Input as the viewing source.

Viewing Sources Note: Be sure to follow

instructions supplied with your computer, and

TV(s) for selecting viewing sources. Computer

image should appear on your Master and other

TVs connected in series.

VIDEO

ANTENNA

CABLE

R- AUDIO- L

S-VIDEO IN

COMPUTER

AUDIO

AUX IN

M.P.I.

TV back

R- AUDIO- L

S-VIDEO OUT

AUDIO OUT

ABC

Video cable

from monitor

Actual

appearance of

components

may vary

Cable for

"video mirror"

Back of computer

Master TV's Computer

output to other TVs

in the "Daisy Chain"

Computer Monitor

Computer

ABC

Computer

input to

Master TV

ABC

Video Out

S-Video Loop-out from Master TV to other TVs

Video Loop-out from Master TV to other TVs

You can “daisy-chain” the TV’s S-Video

or Video output to up to 4 other TVs:

Send the computer image (and sound,

see page 20) to a “Master” TV and

then to other TVs connected in a daisy-

chain series

Notes

• These setups require factory menu item 25

NTSC SCANCARD, default value “0” to be

changed to “1”. (See Installer/Service section

for instructions regarding how to change facto-

ry menu item default values.)

• The cables shown in each of these setups are

not supplied with the Destination II PC/TV.

See your Gateway dealer to purchase the

necessary cables or for further information.

SOURCE

REAR COMPUTER NTSC OUT

PRESS:

SOURCE TO CHANGE

ENTER TO ACTIVATE

S-Video/Video Loop-Out Setups

PAGE 10

206-3643

PC: Windows Environment

Setting your computer for optimum picture output in the Windows operating system environment

The following is a step-by-step procedure for setting your

computer’s picture output to optimum display quality.

1. Hook up your computer to the Destination II PC/TV.

Turn on the Destination II and then the COMPUTER.

2. Open your CONTROL PANEL and click on DISPLAY

PROPERTIES.

3. Click on APPEARANCE. This is where you will make the

changes for a Presentation Display.

At this time you will CREATE a NEW SCHEME or display for

Presentation Display. Once you have created this “new

scheme” you’ll be able to quickly switch between Normal

and Presentation display Scheme. Once you have made

the changes to your computer Scheme, then SAVE AS a

Classroom Display. Use the following steps to change

each ITEM, FONT and COLOR for optimum computer image

viewing on the TV screen.

1. Select under the ITEM and start with ACTIVE TITLE

BAR.

• Select SIZE to 28

• Select COLOR to GREY

• Select FONT

• Select TIMES NEW ROMAN

• Select SIZE 18

• Select COLOR of BLACK

2. Select under the ITEM category CAPTION BUTTONS

• Select SIZE of 25

3. Select under the ITEM category ICON

• Select SIZE of 40

• Select FONT SIZE of 20

• Select FONT of TIMES NEW ROMAN (BOLD)

Technical Update: Optimum Display November 1998

4. Select under the ITEM category ICON SPACING

(Horizontal)

• Select SIZE of 100

5. Select under the ITEM category ICON SPACING

(Vertical)

• Select SIZE of 100

6. Select under the ITEM category INACTIVE TITLE BAR

• Select SIZE of 30

• Select FONT SIZE of 18