Hitachi 36SDX01S/MM1T User manual

Hitachi
Brand
Hitachi
Model
36SDX01S/MM1T
Type
User manual

This manual is also suitable for

Models 36SDX01SR/36SDX01S and 36SDX88B are in the same Solid State Color Television fam-
ily. The main difference between the 36SDX01SR/36SDX01S and 36SDX88B is the control panel
and the CRT. Please refer to model 36SDX88B schematics, assembly, wiring, test and trou-
bleshooting information when servicing models 36SDX01SR/36SDX01S. Refer to Service Manual
PA No. 0110 issued in December 1998.
PA
36SDX01SR/MM1R
36SDX01S/MM1T
No. 0140
R/C: CLU-433FC
Please refer to Service Manual PA No. 0110 when adjusting 36SDX01SR/36SDX01S. The only difference is the Chopper Voltage as
stated below.
SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT
SOLID STATE COLOR TELEVISION
MAY 2000 HHEA-MANUFACTURING DIVISION
NTSC
MM1R/MM1T
SERVICE MANUAL
ADJUSTMENT
# CHOPPER VOLTAGE ADJUSTMENT VGA MODE=112±0.5V VGA MODE=112±0.5V VGA MODE=105±0.5V
(PA No. 0110 SECTION 2.3.1 PAGE 47) DTV MODE=124±0.5V DTV MODE=124±0.5V DTV MODE=120±0.5V
SVGA MODE=140±0.5V SVGA MODE=140±0.5V SVGA MODE=135±0.5V
SYMBOL
NO.
DESCRIPTION 36SDX88B/MM1 36SDX01SR/MM1R 36SDX01S/MM1T
RT01 FOCUS ADJUSTMENT SAME AS STATED SAME AS STATED SEE BELOW
(PA No. 0110 SECTION 3.3 PAGE 81) IN PA No. 0110. IN PA No. 0110.
5. Vertical Line Adjustment
Adjust Focus on Cross-Hatch Circle Pattern focusing
the point as shown in the right figure.
6. Adjust RT01 focusing only at vertical line so that it
becomes the most thick; the adjustment point which
can be seen the clearest without any saturation.
Concentration point:
Inner point of the circle as shown in the fight figure.
Note:
Adjust Horizontal Center Focus again after adjusting
Vertical Focus.
The end of
Cross-Hatch
The second vertical line from
the left end.
RT01
CPT PWB
REAR VIEW
36SDX01S/MM1T ONLY
2
This parts list only gives parts which are different from the service manual PA No. 0110. Components having special safety charac-
teristics are identified by a on the parts list in this Service Data and its supplements and bulletins. Before servicing the chassis,
it is important that the service technician read and follow the ÒSafety PrecautionsÓ and ÒProduct Safety NoticesÓ in this Service Manual.
Do not degrade the safety of the receiver through improper servicing.
!
REPLACEMENT PARTS LIST
CG08 CAP 2125 CHIP 100000PF-K B 25V TA 0893027R -- --
D611 ZENER DIODE 2339825M 2339825M 2339837M
DG09 ZENER HZS12 (C3) 0.005A 2339889M -- --
DG12 DIODE 1SS254TZ/1SS270TA 2344041M -- --
DG13 DIODE 1SS254TA/1SS270TA 2344041M -- --
E801 CRT SOCKET EY00411 EY00411 2698675
ESF FOCUS SCREEN LEAD EZ01001 EZ01001 EZ01003
EVV CONNECTOR (VM) 2973695S 2973695S 2976645
EWK 3P CONNECTOR 2973715S -- --
SYMBOL
NO.
DESCRIPTION
36SDX88B/MM1 36SDX01SR/MM1R 36SDX01S/MM1T
(5) Select MOVIE RATINGS MPAA (PG-13) and TV
RATINGS (TV-Y7/ALL BLOCK)
(6) Check that Picture & audio should be blocked as
follows
“RATING BLOCKED” is displayed when picture is
blocked.
(7) Same check as (1) to (6) should be applied for
PINP sub picture. Main picture should receive a
channel without V-chip signal. Sub picture should
receive a channel with V-chip signal.
NOTE: User setting rating & receive signal rating are
displayed on top area of the screen when
RECALL button is pressed.
1st line : User setting rating.
2nd line : Receive signal rating.
Receive Signal TV-PG MPAA PG TV-Y7-FV
Picture/Audio BLOCK UNBLOCK UNBLOCK
Condition
Receive Signal TV-PG MPAA PG TV-Y7-FV
Picture/Audio BLOCK UNBLOCK BLOCK
Condition
PARENTAL CONTROL (V-Chip) operation check
Preparation for
Adjustment
(1) Receive a channel with V-Chip signal.
(2) Push MENU and select CUSTOM menu by using
왗 or 왘 button.
(3) Select PARENTAL CONTROL by using 왖 or 왔
button.
(4) Press 왘 button to set PARENTAL CONTROL
mode.
(5) Enter “7777” for SECRET CODE.
(6) Select MOVIE RATINGS and TV RATING by
using 왖 or 왔 button.
(7) Press 왘 button to set MOVIE RATINGS and TV
RATINGS.
Adjustment Procedure
(1) Select MOVIE RATINGS MPAA (PG) and TV
RATINGS (TV-14/ALL BLOCK)
(2) Check that Picture & audio should be blocked as
follows
“RATING BLOCKED” is displayed when picture is
blocked.
(3) Select MOVIE RATINGS MPAA (PG-13) and TV
RATINGS (TV-14/ALL BLOCK)
(4) Check that Picture & audio should be blocked as
follows
“RATING BLOCKED” is displayed when picture is
blocked.
Receive Signal TV-PG MPAA PG TV-Y7-FV
Picture/Audio UNBLOCK BLOCK UNBLOCK
Condition
36SDX01SR/MM1R AND 36SDX01S/MM1T ONLY
3
I001 MAIN MICRO-CONTROLLER CP05361 CP05362 CP05362
JY91 3P(SW) PIN JACK WITH S ES00022 -- --
JY91 JACK 03P HORIZONTAL -- ES00261 ES00261
JY92 JACK S-TERMINAL -- ES00271 ES00271
K400 JUMPER WIRE (0.5 L=52MM) 2974432M -- --
K406 JUMPER WIRE (0.5 L=52MM) 2974432M -- --
K411 JUMPER WIRE (0.5 L=52MM) 2974432M -- --
K412 JUMPER WIRE (0.5 L=52MM) 2974432M -- --
K421 JUMPER WIRE (0.5 L=52MM) 2974432M -- --
K442 JUMPER WIRE (0.5 L=52MM) 2974432M -- --
K481 JUMPER WIRE (0.5 L=52MM) 2974432M -- --
K482 JUMPER WIRE (0.5 L=52MM) 2974432M -- --
K8A1 JUMPER WIRE (0.5 L=52MM) 2974432M -- --
K8A2 JUMPER WIRE (0.5 L=52MM) 2974432M -- --
KT01 JUMPER WIRE (0.5 L=52MM) -- -- 2974432M
KT02 JUMPER WIRE (0.5 L=52MM) -- -- 2974432M
KT03 JUMPER WIRE (0.5 L=52MM) -- -- 2974432M
KT04 JUMPER WIRE (0.5 L=52MM) -- -- 2974432M
KT05 JUMPER WIRE (0.5 L=52MM) -- -- 2974432M
N201 INSTRUCTION BOOK QR27362 QR45391 QR45391
N203 V-CHIP REFERENCE GUIDE -- H462678 H462678
PVV PLUG PIN SUB MINI 2902262 2902262 2902261
PWK PLUG PIN SUB MINI 3P 2902262 -- --
R624 RESISTOR 0700056M 0700056M 0700062M
R625 RESISTOR 0700056M 0700056M 0700062M
R627 RESISTOR 0700054M 0700054M 0700058M
R627 RESISTOR 0700054M 0700054M 0700053M
RG18 1.2K OHM (1/16 W) 0195902R 0700042M 0700042M
RG30 RES.-CARBON FLM 1/16W 100-JB 0700027M -- --
RG40 10K OHM (1/16 W) 0195925R 0700054M 0700054M
RKJ1 RES 2125 CHIP 1/16W 000 TAPE 0195250R -- --
RKJ2 RES 2125 CHIP 1/16W 000 TAPE 0195250R -- --
RKJ3 RES 3216 CHIP 1/8W 000 TAPE 0195248R -- --
RKJ4 JUMPER 0195250R 2974432M 2974432M
RKJ5 JUMPER 0195250R 2974432M 2974432M
RT01 VARIABLE RESISTOR 20MΩ -- -- AW00241
SYMBOL
NO.
DESCRIPTION
36SDX88B/MM1 36SDX01SR/MM1R 36SDX01S/MM1T
This parts list only gives parts which are different from the service manual PA No. 0110. Components having special safety charac-
teristics are identified by a on the parts list in this Service Data and its supplements and bulletins. Before servicing the chassis,
it is important that the service technician read and follow the ÒSafety PrecautionsÓ and ÒProduct Safety NoticesÓ in this Service Manual.
Do not degrade the safety of the receiver through improper servicing.
!
REPLACEMENT PARTS LIST
4
RL12 RESISTOR 0700033M 0700033M 0700029M
RL18 RESISTOR 0700036M 0700036M 0700032M
SG01 5 KEY PUSH SWITCH 2632851 2633322 2633322
SG02 PUSH SWITCH 2634621 FE10332R FE10332R
SG03 PUSH SWITCH 2634621 FE10332R FE10332R
TH01 FBT BW00757 BW00757 BW02491
UG02 IC TPS831 CZ00781 -- --
V1 PICTURE TUBE DE01351 DE01351 DE01921
(A90AGW14X04) (A90AGW14X04) (M90AHL50X33)
#030 FRONT FRAME QD03492 QD09791 QD09791
#030 BACK COVER Q001574 QD09621 QD09621
SYMBOL
NO.
DESCRIPTION
36SDX88B/MM1 36SDX01SR/MM1R 36SDX01S/MM1T
!
This parts list only gives parts which are different from the service manual PA No. 0110. Components having special safety charac-
teristics are identified by a on the parts list in this Service Data and its supplements and bulletins. Before servicing the chassis,
it is important that the service technician read and follow the ÒSafety PrecautionsÓ and ÒProduct Safety NoticesÓ in this Service Manual.
Do not degrade the safety of the receiver through improper servicing.
!
REPLACEMENT PARTS LIST
PRINTED CIRCUIT BOARD
CPT P.W.B.
5
6
NOTES:
7
26
24
25
1
3
33
2
31
32
34
A
1
앫 All DC voltage to be measured with a tester (100k액/V). Voltage taken on a complex color bar signal including a standard color bar signal.
앫 Since this is a basic circuit diagram, the value of the parts is subject to be altered for improvement.
POWER DEFLECTION
PRODUCT SAFETY NOTE: Components marked with a and shaded have special characteristics important to
safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service
Manual. DonÕt degrade the safety of the receiver through improper servicing.
BASIC CIRCUIT DIAGRAM
POWER DEFLECTION
SIGNAL 1 OF 3
32456
132456
B
C
D
E
A
B
C
D
E
8
10
9
4
5
6
7
8
A
1
앫 All DC voltage to be measured with a tester (100k액/V). Voltage taken on a complex color bar signal including a standard color bar signal.
앫 Since this is a basic circuit diagram, the value of the parts is subject to be altered for improvement.
SIGNAL 1 OF 3
PRODUCT SAFETY NOTE: Components marked with a and shaded have special characteristics important to
safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service
Manual. DonÕt degrade the safety of the receiver through improper servicing.
BASIC CIRCUIT DIAGRAM
POWER DEFLECTION
SIGNAL 1 OF 3
32456
132456
B
C
D
E
A
B
C
D
E
9
A
1
앫 All DC voltage to be measured with a tester (100k액/V). Voltage taken on a complex color bar signal including a standard color bar signal.
앫 Since this is a basic circuit diagram, the value of the parts is subject to be altered for improvement.
PRODUCT SAFETY NOTE: Components marked with a and shaded have special characteristics important to
safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service
Manual. DonÕt degrade the safety of the receiver through improper servicing.
BASIC CIRCUIT DIAGRAM
SIGNAL 2 OF 3
SIGNAL 3 OF 3
32456
132456
B
C
D
E
A
B
C
D
E
SIGNAL 2 OF 3
10
30
29
28
13
12
11
14
17
22
23
21
20
1918
16
15
A
1
앫 All DC voltage to be measured with a tester (100k액/V). Voltage taken on a complex color bar signal including a standard color bar signal.
앫 Since this is a basic circuit diagram, the value of the parts is subject to be altered for improvement.
PRODUCT SAFETY NOTE: Components marked with a and shaded have special characteristics important to
safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service
Manual. DonÕt degrade the safety of the receiver through improper servicing.
BASIC CIRCUIT DIAGRAM
SIGNAL 2 OF 3
SIGNAL 3 OF 3
32456
132456
B
C
D
E
A
B
C
D
E
SIGNAL 3 OF 3
BNCNC
CNCNC
ENCNC
BNCNC
CNCNC
ENCNC
BNCNC
CNCNC
ENCNC
B 3.8 4.4
C 11.0 10.7
E 3.1 3.7
B 11.2 11.2
C 11.9 6.1
E 11.0 10.8
B 11.8 11.8
C 149.4 1.5
E 11.3 11.2
B 149.6 1.6
C00
E 150.5 1.8
B 151.2 1.8
C 218.4 218.7
E 150.8 1.9
B00
C 11.9 11.8
E00
B 3.6 4.3
C 11.0 10.8
E 2.9 3.6
Q801
Q802
Q803
Q804
Q805
Q806
Q807
Q808
Q809
Q810
CICUIT# PIN#
DC voltage
Vdc
TV mode PC mode
B 11.3 11.3
C 11.9 11.9
E 11.0 10.9
B 11.9 11.8
C 152.9 2.0
E 11.3 11.2
B 152.5 110.8
C00
E 153.3 2.3
B 154.6 2.1
C 218.3 218.8
E 154.5 2.1
B00
C 6.0 6.1
E00
B 11.3 11.2
C 11.9 11.9
E 11.0 10.8
B 11.8 11.8
C 162.1 2.2
E 11.3 11.2
B 162.1 2.2
C00
E 162.7 2.4
B 163.4 2.4
C 218.3 218.6
E 163.2 2.5
B 3.5 4.2
C 11.0 10.9
E 2.8 3.4
Q816
Q817
Q818
Q819
Q820
Q811
Q812
Q813
Q814
Q815
CICUIT# PIN#
DC voltage
Vdc
TV mode PC mode
PAGE 179
35
36
27
A
1
앫 All DC voltage to be measured with a tester (100k액/V). Voltage taken on a complex color bar signal including a standard color bar signal.
앫 Since this is a basic circuit diagram, the value of the parts is subject to be altered for improvement.
TUNER
PRODUCT SAFETY NOTE: Components marked with a and shaded have special characteristics important to
safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service
Manual. DonÕt degrade the safety of the receiver through improper servicing.
BASIC CIRCUIT DIAGRAM
TUNER
CPT
32456
132456
B
C
D
E
A
B
C
D
E
PAGE 179
A
1
앫 All DC voltage to be measured with a tester (100k액/V). Voltage taken on a complex color bar signal including a standard color bar signal.
앫 Since this is a basic circuit diagram, the value of the parts is subject to be altered for improvement.
CPT
PRODUCT SAFETY NOTE: Components marked with a and shaded have special characteristics important to
safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service
Manual. DonÕt degrade the safety of the receiver through improper servicing.
BASIC CIRCUIT DIAGRAM
TUNER
CPT
32456
132456
B
C
D
E
A
B
C
D
E
PAGE 179
A
1
앫 All DC voltage to be measured with a tester (100k액/V). Voltage taken on a complex color bar signal including a standard color bar signal.
앫 Since this is a basic circuit diagram, the value of the parts is subject to be altered for improvement.
VM
PRODUCT SAFETY NOTE: Components marked with a and shaded have special characteristics important to
safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service
Manual. DonÕt degrade the safety of the receiver through improper servicing.
BASIC CIRCUIT DIAGRAM
VM
CONTROL PANEL
32456
132456
B
C
D
E
A
B
C
D
E
PAGE 179
A
1
앫 All DC voltage to be measured with a tester (100k액/V). Voltage taken on a complex color bar signal including a standard color bar signal.
앫 Since this is a basic circuit diagram, the value of the parts is subject to be altered for improvement.
CONTROL PANEL
PRODUCT SAFETY NOTE: Components marked with a and shaded have special characteristics important to
safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service
Manual. DonÕt degrade the safety of the receiver through improper servicing.
BASIC CIRCUIT DIAGRAM
VM
CONTROL PANEL
32456
132456
B
C
D
E
A
B
C
D
E
NOTES:
11
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Hitachi 36SDX01S/MM1T User manual

Hitachi
Brand
Hitachi
Model
36SDX01S/MM1T
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents