2. Behringer
  3. EUROPORT MPA100BT
EUROPORT MPA100BT

Behringer EUROPORT MPA100BT Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the Behringer EUROPORT MPA100BT Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
NCDW
Portable PA System
District Operations Manual
System
1 Behinger MPA100BT
100watt 2 channel with bluetooth
Channels can be wire ¼ balance or XLR unbalance
Channels can be wireless bluetooth mics
System can support maximum of 2 channels
Aux input with Blue tooth or 1/8/3mm aux input for computer/mobile phone
1 Wireless Behinger ULM300 single wireless mic.
1 Wireless mic and ULM300 transmitter
1 Wireless Behinger ULM200 dual wireless mic
2 Wireless mics and ULM200 transmitter
1 Gator mic bag
Bag to carry 5 mics and power cords.
1 Mic Stand
1 MIcStdFBoomL MS7701B Mic std w/fixed boom
1 Speaker Stand
1 GFWSPK2000 Speaker Stand
1 Mic Stand clip
MY110 Dynamic Rubber Mic Clip
1 Stand bag
SpeakerStdBg 50” Heavy Duty Stand Bag
MPA100BT All in One Portable PA System
Overview
System works on 120V power or internal 6 Volt Lead Acid battery.
If fully charge will work for 20 hours on battery. Takes 48 hours to fully charge battery.
2 adjustable mic channels that can be wire and/ou blue tooth mics. Can only support 2 mics at a
time. Each mic has it own volumne/gain control.
1 aux channel gain control for computer or mobile phone. Input can be blue tooth or ⅛,3mm
wired.
1 master volume for overall mix with selection of music only or speaking
1 on/off power switch
1 battery status level
Set up
1. Charge unit min 48 hours before event.
a. Connect power cord to unit and leave off to charge.
2. Set up speaker stand or set system on a solid surface.
3. Using wireless mic inset transmitter that cooresponds to mic or mics being used into
USB port.
4. Turn power on, if using 120V connect power cord and plug into power source.
5. USB transmitter should be blinking.
6. Turn wireless mic on by pressing up button and holding until solid. Mic is linked to
transmitter.
a. If using dual mic will have to do for both mics.
7. Connecting bluetooth to laptop or mobile phone. On top of MPA 100 press bluetooth
button. It will start blinking find on mobile device and select. The bluetooth button
should be solid and mobile device should show it is link to speaker.
Operation
1. Turn Power on to unit
2. Link up wireless Mics
3. Adjust mic gain
4. Adjust computer/mobile phone input gain if used
5. Adjust overall master volume
6. As speaker speaks should see indication on LEDs for each wireless mic.
7. Bluetooth automatically links to someone else phone, press and hold bluetooth button
until it is blinking then reselect with correct device. This will also disconnect a device.
8. Each mic has an up and down control. This allows speaker to adjust level. If the down
button is held mic will mute and show by having a blinking LED. If down button is
continued to be depress mic will turn off. To turn back on press up button. If mic is turn
off and back on the it will remember the bluetooth link.
Mic operation
Single wireless Mic Dual wireless mic
Top buttom Volume up Left Button Volume Up
BT link BT Link
Power on Power on
Buttom Volume Down Right Button Volume Down
Mute Mute
Power off Power off
Mic Battery Removal
Battery should not be left in. Recommend removal of batteries between each use.
1. Unscrew bottom of mic
2. Open battery door by depress tap at top and pulling door down.
LinkIng Blue Mics
1. Insert transmitter into PA system
a. ULM 300 is for single mic
b. ULM200 is for dual mics
2. LED on side will blink until Linked
3. Solid LED mic is Linked to transmitter
4. Computer/mobile phone Bluetooth Link button is on top.
/