Comelit 1622L is an audio module for door entry systems. It allows for communication between a visitor at the door and a resident inside the building. The module has a built-in microphone and speaker for clear audio transmission. Additionally, it features a signaling LED that indicates the status of the system, such as when a call is being made or when the door is opened.
The Comelit 1622L can be programmed to work with up to 240 different users, making it suitable for use in small to medium-sized residential or commercial buildings. Each user can be assigned a unique code, which they can use to open the door or gate. The module also has a built-in timer that can be set to automatically lock the door after a certain amount of time, providing an additional level of security.
Comelit 1622L is an audio module for door entry systems. It allows for communication between a visitor at the door and a resident inside the building. The module has a built-in microphone and speaker for clear audio transmission. Additionally, it features a signaling LED that indicates the status of the system, such as when a call is being made or when the door is opened.
The Comelit 1622L can be programmed to work with up to 240 different users, making it suitable for use in small to medium-sized residential or commercial buildings. Each user can be assigned a unique code, which they can use to open the door or gate. The module also has a built-in timer that can be set to automatically lock the door after a certain amount of time, providing an additional level of security.
EN
TECHNICAL
MANUAL
Audio module Art. 1622 and Art. 1622L
2
Warning
Table of contents
• Install the equipment by carefully following the instructions given by the manufacturer and in compliance with the
standards in force. Do not tamper with the internal elements offering protection against short circuits and overcurrents.
• All the equipment must only be used for the purpose it was designed for. Comelit Group S.p.A. declines any
responsibility for improper use of the apparatus, for any alterations made by others for any reason or for the use of
non-original accessories or materials.
• All the products comply with the requirements of the 2014/30/EU and 2014/35/EU directives. This is proved by the
CE mark on the products themselves.
• Do not route the riser wires in proximity to power supply cables (230/400V).
• Installation, mounting and assistance procedures for electrical devices must only be performed by specialised
electricians.
• Disconnect the power supply before carrying out any maintenance procedures.
• Connect the module support frame to earth (see Fig.)
Warning ............................................................................................ 2
Description ....................................................................................... 3
Installation information ................................................................... 4
Installation with Ikall external unit ................................................. 5
Installation with Vandalcom (A) Roma (B) external unit ............... 6
Vandalcom (A) ...........................................................................................6
Roma (B) ...................................................................................................6
Button programming ....................................................................... 7
Dip switch programming table ....................................................... 8
EXAMPLE: dip switch setting for code 200 ...........................................9
Special programming .................................................................... 10
Special programming table ...................................................................11
Operating distances with Art. 1595 .............................................. 13
Operating distances ............................................................................... 13
Maximum system expansion ................................................................. 13
Wiring diagrams............................................................................. 14
Door-entry phone system with 1 audio port, Ikall series. Switching on/
voltage check with system in standby. ................................................14
Door-entry phone system with 2 audio ports, Ikall series .................15
Wiring diagram for system with digital call module Art.3360 ...........16
Wiring diagram with safety lock ...........................................................16
Using the external unit relay on lock-release or actuator control .....17
Door open indication use variant..........................................................17
Protection device connection variant for line Art. 1237 .....................18
Use of RC network for lock filter on relay contacts ...........................18
ON DIP
ON
OFF
1.
2. 3.
4. 5.
6.
1. 4.
5.
6.
7.
3.2.
3
Description
1. DIP switches for function programming and setting the
user code.
2. Switch for input/output programming.
3. Loudspeaker volume control.
4. Connector for additional module connection.
5. Jumper for managing the RC network for door lock filter
on relay contacts.
6. Terminal block for connection:
SE electric lock connection
COM common relay contact
NC normally closed relay contact
NO normally open relay contact
GND input reference negative for DO-RTE
PR programming input
DO door opened signal input
RTE local lock release input
V- power supply negative
V+ power supply positive
LL bus line connection
1. Signalling LED: call sent (Art. 1622L only).
2. Speaker.
3. Microphone.
4. Signalling LED: system busy (Art. 1622L only).
5. Signalling LED: audio activated (Art. 1622L only).
6. Signalling LED: lock-release activated (Art. 1622L only).
7. Loudspeaker volume control.
4
Installation information
• The system can manage up to 240 users, connecting MAX 100 internal units for each riser and 3 internal units with the
same user code. If the additional Art. 1252 is used, up to 16 internal units can be connected in parallel.
• If using risers with over 30 Easycom door-entry phones Art. 6228W or Art. 6228B, apply SB2 technology (with mixer Art.
4888 or Art. 4888C) when installing these risers.
• Modules Art. 1622/Art. 1622L normally function as a main external unit (timed busy signal).
• To set them as a secondary external unit (busy signal active for the whole time the riser is in use), set all the selector DIP
switches to ON.
• When a call is transmitted from the external unit, if a busy tone is heard instead of the ringtone, this means communication
with another external unit is in progress.
• In the event of a persistent short-circuit on the bus line, the external unit emits an intermittent signalling tone.
Only Art. 1622L is fitted with a signalling LED and the “voice messages” function. The signalling LEDs
(busy, call sent, door opened, communication active) are only available with the faceplates of the kit
33400K.
Art. 1622L can only be fitted to single-plate external units with accessory 1250IAL.
21
LED
O
F
F
LED
O
F
F
WHITE OFF
BLUE
3
Nameplate LED lighting
selection.
open
close
54
Speaker adjustment
Alternative microphone position
(excluding 4 module entrance panel)
3
2
1
5
4
5
Installation with Ikall external unit
orange
white
green
orange
white
green
21
ALTO
ALTO
ALTO
white
green
orange
ALTO
3A 4A 5A
orange
white
green
3B 4B 5B
6
Installation with Vandalcom (A) Roma (B) external unit
Vandalcom (A)
Roma (B)
5 64
33433
33434
33436
33433
33434
33436
-V
+V
321
Set the user code using the
dip switches; see “Dip switch
programming table”.
7
Button programming
8
Dip switch programming table
Cod
Dip switch
ON
Name
1 1
2 2
3 1,2
4 3
5 1,3
6 2,3
7 1,2,3
8 4
9 1,4
10 2,4
11 1,2,4
12 3,4
13 1,3,4
14 2,3,4
15 1,2,3,4
16 5
17 1,5
18 2,5
19 1,2,5
20 3,5
21 1,3,5
22 2,3,5
23 1,2,3,5
24 4,5
25 1,4,5
26 2,4,5
27 1,2,4,5
28 3,4,5
29 1,3,4,5
30 2,3,4,5
31 1,2,3,4,5
32 6
33 1,6
34 2,6
35 1,2,6
36 3,6
37 1,3,6
38 2,3,6
39 1,2,3,6
40 4,6
41 1,4,6
42 2,4,6
43 1,2,4,6
44 3,4,6
45 1,3,4,6
46 2,3,4,6
47 1,2,3,4,6
48 5,6
Cod
Dip switch
ON
Name
49 1,5,6
50 2,5,6
51 1,2,5,6
52 3,5,6
53 1,3,5,6
54 2,3,5,6
55 1,2,3,5,6
56 4,5,6
57 1,4,5,6
58 2,4,5,6
59 1,2,4,5,6
60 3,4,5,6
61 1,3,4,5,6
62 2,3,4,5,6
63 1,2,3,4,5,6
64 7
65 1,7
66 2,7
67 1,2,7
68 3,7
69 1,3,7
70 2,3,7
71 1,2,3,7
72 4,7
73 1,4,7
74 2,4,7
75 1,2,4,7
76 3,4,7
77 1,3,4,7
78 2,3,4,7
79 1,2,3,4,7
80 5,7
81 1,5,7
82 2,5,7
83 1,2,5,7
84 3,5,7
85 1,3,5,7
86 2,3,5,7
87 1,2,3,5,7
88 4,5,7
89 1,4,5,7
90 2,4,5,7
91 1,2,4,5,7
92 3,4,5,7
93 1,3,4,5,7
94 2,3,4,5,7
95 1,2,3,4,5,7
96 6,7
Cod
Dip switch
ON
Name
97 1,6,7
98 2,6,7
99 1,2,6,7
100 3,6,7
101 1,3,6,7
102 2,3,6,7
103 1,2,3,6,7
104 4,6,7
105 1,4,6,7
106 2,4,6,7
107 1,2,4,6,7
108 3,4,6,7
109 1,3,4,6,7
110 2,3,4,6,7
111 1,2,3,4,6,7
112 5,67
113 1,5,6,7
114 2,5,6,7
115 1,2,5,6,7
116 3,5,6,7
117 1,3,5,6,7
118 2,3,5,6,7
119 1,2,3,5,6,7
120 4,5,6,7
121 1,4,5,6,7
122 2,4,5,6,7
123 1,2,4,5,6,7
124 3,4,5,6,7
125 1,3,4,5,6,7
126 2,3,4,5,6,7
127 1,2,3,4,5,6,7
128 8
129 1,8
130 2,8
131 1,2,8
132 3,8
133 1,3,8
134 2,3,8
135 1,2,3,8
136 4,8
137 1,4,8
138 2,4,8
139 1,2,4,8
140 3,4,8
141 1,3,4,8
142 2,3,4,8
143 1,2,3,4,8
144 5,8
9
Cod
Dip switch
ON
Name
145 1,5,8
146 2,5,8
147 1,2,5,8
148 3,5,8
149 1,3,5,8
150 2,3,5,8
151 1,2,3,5,8
152 4,5,8
153 1,4,5,8
154 2,4,5,8
155 1,2,4,5,8
156 3,4,5,8
157 1,3,4,5,8
158 2,3,4,5,8
159 1,2,3,4,5,8
160 6,8
161 1,6,8
162 2,6,8
163 1,2,6,8
164 3,6,8
165 1,3,6,8
166 2,3,6,8
167 1,2,3,6,8
168 4,6,8
169 1,4,6,8
170 2,4,6,8
171 1,2,4,6,8
172 3,4,6,8
173 1,3,4,6,8
174 2,3,4,6,8
175 1,2,3,4,6,8
176 5,6,8
Cod
Dip switch
ON
Name
177 1,5,6,8
178 2,5,6,8
179 1,2,5,6,8
180 3,5,6,8
181 1,3,5,6,8
182 2,3,5,6,8
183 1,2,3,5,6,8
184 4,5,6,8
185 1,4,5,6,8
186 2,4,5,6,8
187 1,2,4,5,6,8
188 3,4,5,6,8
189 1,3,4,5,6,8
190 2,3,4,5,6,8
191 1,2,3,4,5,6,8
192 7,8
193 1,7,8
194 2,7,8
195 1,2,7,8
196 3,7,8
197 1,3,7,8
198 2,3,7,8
199 1,2,3,7,8
200 4,7,8
201 1,4,7,8
202 2,4,7,8
203 1,2,4,7,8
204 3,4,7,8
205 1,3,4,7,8
206 2,3,4,7,8
207 1,2,3,4,7,8
208 5,7,8
Cod
Dip switch
ON
Name
209 1,5,7,8
210 2,5,7,8
211 1,2,5,7,8
212 3,5,7,8
213 1,3,5,7,8
214 2,3,5,7,8
215 1,2,3,5,7,8
216 4,5,7,8
217 1,4,5,7,8
218 2,4,5,7,8
219 1,2,4,5,7,8
220 3,4,5,7,8
221 1,3,4,5,7,8
222 2,3,4,5,7,8
223 1,2,3,4,5,7,8
224 6,7,8
225 1,6,7,8
226 2,6,7,8
227 1,2,6,7,8
228 3,6,7,8
229 1,3,6,7,8
230 2,3,6,7,8
231 1,2,3,6,7,8
232 4,6,7,8
233 1,4,6,7,8
234 2,4,6,7,8
235 1,2,4,6,7,8
236 3,4,6,7,8
237 1,3,4,6,7,8
238 2,3,4,6,7,8
239 1,2,3,4,6,7,8
240* 5,6,7,8
EXAMPLE: dip switch setting for code 200
*NOTE: code 240 is reserved for the porter switchboard
PR
GND
7
-V
+V
PR
GND
1
3
2
6
1 sec
4 5
Set the dip switches for the
function you wish to program, see
“Special programming table”.
10
Special programming
CODE DIP SWITCH ON FUNCTIONS
Audio-visal messages (Art. 1622L only)
210 2,5,7,8 visual messages only (Art. 1622L only)
211 1,2,5,7,8 Swedish (Art. 1622L only)
214 2,3,5,7,8 OFF (default) (Art. 1622L only)
215 1,2,3,5,7,8 Italian (Art. 1622L only)
216 4,5,7,8 French (Art. 1622L only)
217 1,4,5,7,8 Spanish (Art. 1622L only)
218 2,4,5,7,8 Dutch (Art. 1622L only)
219 1,2,4,5,7,8 Greek (Art. 1622L only)
220 3,4,5,7,8 English (Art. 1622L only)
221 1,3,4,5,7,8 German (Art. 1622L only)
222 2,3,4,5,7,8 Portuguese (Art. 1622L only)
Door lock
223 1,2,3,4,5,7,8
Door lock command on SE in AC (default)
224 6,7,8
Door lock command on SE in enhanced AC
225 1,6,7,8
Door lock command on SE in DC
245 1,3,5,6,7,8 Door lock time: 2 sec + deactivation tone (default)
246 2,3,5,6,7,8
Door lock time: 4 sec
247 1,2,3,5,6,7,8
Door lock time: 8 sec
248 4,5,6,7,8
Door lock confirmation tone: enabled
251 1,2,4,5,6,7,8
C.NC.NO relay in parallel with SE (default)
252 3,4,5,6,7,8
Lock-release always enabled (default)
253 1,3,4,5,6,7,8
Lock-release only enabled for user called
Actuator control management
N.B. the system should not include Art. 1256 in generic actuator mode.
229 1,3,6,7,8 Enabling C.NC.NO relay on actuator control: 2 sec
230 2,3,6,7,8 Enabling C.NC.NO relay on actuator control: 4 sec
231 1,2,3,6,7,8 Enabling C.NC.NO relay on actuator control: 8 sec
228 3,6,7,8 Actuator control on serial line S: disabled (default)
227 1,2,6,7,8 Actuator control on serial line S: enabled
System functions
232 4,6,7,8
Awaiting response time: 60 sec (default)
233 1,4,6,7,8
Awaiting response time: 120 sec
234 2,4,6,7,8
Awaiting response time: 30 sec
235 1,2,4,6,7,8
Talk time: 90 sec (default)
236 3,4,6,7,8
Talk time: 180 sec
237 1,3,4,6,7,8
Self-ignition: enabled (default)
238 2,3,4,6,7,8
Self-ignition: disabled
239 1,2,3,4,6,7,8 Confirmation tone on user call: enabled (default)
240 5,6,7,8 Confirmation tone on user call: disabled
11
Special programming table
243 1,2,5,6,7,8
Reset wait time: 10 sec (default)
244 3,5,6,7,8
Reset wait time: 1 sec
208 5,7,8
Reset after lock-release in audio: enabled (default)
209 1,5,7,8
Reset after lock-release in audio: disabled
249 1,4,5,6,7,8
Call transmission: single (default)
250 2,4,5,6,7,8
Call transmission: triple
241 1,5,6,7,8 Gestione posti interni collegati all'Art. 1622: fino a 70 (default)
242 2,5,6,7,8 Gestione posti interni collegati all'Art. 1622: da 71 a 100
System mode
0
Simplebus (default)
255 1,2,3,4,5,6,7,8
Simplebus Top
254 2,3,4,5,6,7,8 Restore default
12
A
15951622
B
13
Operating distances with Art. 1595
Operating distances
A MAX B MAX
1 mm² (Ø 1,2 mm AWG 17)
50 m
(165 feet)
500 m
(1625 feet)
0,28 mm² (Ø 0,6 mm AWG 23)
5 m
(15 feet)
300 m
(990 feet)
0,5 mm² (Ø 0,8 mm AWG 20)
25 m
(85 feet)
400 m
(1315 feet)
1,5 mm² (Ø 1,4 mm AWG 15)
75 m
(245 feet)
600 m
(1980 feet)
2,5 mm² (Ø 1,8 mm AWG 13)
100 m
(330 feet)
800 m
(2600 feet)
Maximum system expansion
Max. number of door-entry phones that can be
connected
100
Max. number of internal units with the same user code 3
Max. number of call repetition devices 1
14
Wiring diagrams
Door-entry phone system with 1 audio port, Ikall series. Switching on/voltage check with
system in standby.
-
+
1595
120-230V
26-28 Vdc
SB/TNP
Local lock release button.
15
Door-entry phone system with 2 audio ports, Ikall series
Local lock release button.
-
+
1595
120-230V
-
+
1595
120-230V
SBC/014NP
16
Wiring diagram for system with digital call module Art.3360
Wiring diagram with safety lock
Local lock release button.
1595
+
-
120-230V
SB/QNP
Local lock release button.
1595
+
-
120-230V
SB2/SNP
17
Using the external unit relay on lock-release or actuator control
Door open indication use variant
1595
+
-
120-230V
Only for use in systems with a single external unit without switching devices Art. 1224A, Art. 1424.
N.C. contact for DOOR OPEN indication. The LED for the following internal units flashes: Art. 2610 with R.I. 008, Art.
2619 with R.I. 000.
SB/DO
Local lock release button.
E
S
NC NO
D
N
G
R
P
R
T
E
-
V V
+
M
O
C
D
O
L L
1622
12V/24V
AC-DC
J1
J2
33436
J1
J2
10A MAX
230 V
120-230 V
-
+
1595
+
-
SB/RTNP
f “C.NC.NO relay activation on actuator command: 2 sec”
f Set the dip switches permanently as shown in the figure (Dip switch ON 8, Dip switch
OFF 1,2,3,4,5,6,7)
Applies to Art. 1622L.
Applies to Art. 1622 with R.I. 038 or greater
18
Protection device connection variant for line Art. 1237
Use of RC network for lock filter on relay contacts
Local lock release button.
1595
+
-
120-230V
SB2V/SCA
On C. NO
contacts.
On C. NC
contacts.
Excluded: voltage-free
contact
Jumper
19
1
st
edition 09/2016
cod. 2G40001833
www.comelitgroup.com
Via Don Arrigoni, 5 - 24020 Rovetta (BG) - Italy
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Comelit 1622L Technical Manual
- Type
- Technical Manual
- This manual is also suitable for
Comelit 1622L is an audio module for door entry systems. It allows for communication between a visitor at the door and a resident inside the building. The module has a built-in microphone and speaker for clear audio transmission. Additionally, it features a signaling LED that indicates the status of the system, such as when a call is being made or when the door is opened.
The Comelit 1622L can be programmed to work with up to 240 different users, making it suitable for use in small to medium-sized residential or commercial buildings. Each user can be assigned a unique code, which they can use to open the door or gate. The module also has a built-in timer that can be set to automatically lock the door after a certain amount of time, providing an additional level of security.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Comelit 4680C Technical Manual
-
-
-
-
-
-
-
-
-
Other documents
-
Camlink CL-ROMA300G Datasheet
-
Metabo W 24-230 Operating instructions
-
Walker Edison Furniture Company HD8401 Operating instructions
-
Sensata ISOSLICE-4 User manual
-
Wisenet QNP-6320H User manual
-
Ditel DN-NN Technical Manual
-
Wavecom TnP Prime Owner's manual
-
DEA LIVI 550 User manual
-
fortessa DIGI-2 User manual
-
Golmar TRIP T632/G2+ SE ML REV.0122 Owner's manual
