Page is loading ...
CORNER ELEVATED GARDEN PLANTER ASSEMBLY INSTRUCTIONS
Tools Included
Assembly Instructions
A - (1) Long side panel - 23-7/8" x 48"
B - (2) Short side panels - 23-7/8" x 32-7/8"
C - (3) 22-1/2" Corner wedges
D - (3) 8-1/2" Corner wedges
E - (1) 23-3/4" Ledge piece
F - (2) 10-1/2" Ledge pieces
G - (1) Shelf piece
H - (24) 1-1/2" Bolts
I - (1) 54" Trim pieces
J - (2) 40" Trim pieces
K - (9) 1" Screws
5/32" Allen wrench
Phillips-head bit
1. Place the long edges of (2) 22-1/2" corner wedges (C) to the
inside of the long side panel (A) and attach by fastening the
supplied bolts (H) through the predrilled holes. Note: each
corner wedge has predrilled holes in different locations. Be
sure to use the corner wedges with the predrilled holes in
the long edges. (Fig. 1)
Installation tip: Place the panel (A) groove-side down on
a table or workbench, with the predrilled holes hanging off
the table or bench. Place the corner wedge (C) against
the panel, align the predrilled holes and insert the bolts
(H) from the bottom.
2. Align the 23-1/4” ledge piece (E) with the center predrilled
holes on the long side panel (A) and fasten using supplied
bolts (H). Align the 10-1/2” ledge pieces (F) with the center
predrilled holes on each of the short side panels (B) and
fasten using supplied bolts (H).
3. The edges of each side panel are marked with either one
dot or two dots. Align each panel so that the corresponding
markings face each other. Attach the remaining 22-1/2"
corner wedge (C) to the inside of one short side panel (B)
by fastening the supplied bolts (H) through the predrilled
holes. Attach all side panels (B) to the corner wedges to
form a triangle using the supplied bolts. (Fig. 2)
4. Place shelf piece (G) on ledge pieces (F). (Fig. 3)
Fig. 1
Fig. 2
Fig. 3
Parts Included
A
A
C
H
H
C
B
F
F
F
F
B
H
HC
G
UFP Granger, LLC • 50415 Herbert Street, Granger, IN 46530 • 574.277.7670 • OutdoorEssentialProducts.com
©2013 Universal Forest Products, Inc. All rights reserved. Outdoor Essentials is a registered trademark of Universal Consumer Products, Inc. 7399 _ENG_08/13
5. Attach (3) 8-1/2" corner wedges (D) to side panels
above the shelf piece by fastening the supplied bolts (H)
through the predrilled holes. (Fig. 4)
6. Attach the 54" trim piece (I) to the outside of the long side
panel, and the 40" trim pieces (J) to the outside of the
short side panels, by driving the 1" screws (K) through the
panels from the inside of the planter, biting into the trim.
Use (3) screws on each side. (Fig. 5)
Note: The customer needs to cut the trim pieces to fit.
Note: Due to the weight of potting material, we recommend
that you place the elevated garden bed in its desired
location before filling it.
Fig. 4
Fig. 5
This brochure is for illustration purposes only. Use of this product must be in accordance with all local zoning and/or building codes. Consumer assumes all risks and liability
associated with the use of this product. For details on safe handling and warranty information, go to UFPI.com/ptinfo.
D
D
D
H
H
H
H
H
H
I
J
Project time: Approximately 30-60 minutes, depending on skill set
Finished dimensions: 24" L x 24" W x 31-1/2" H, 54" long side
Planting depth: 8.5"
/
