Owner’s Manual and Instructions
Model No. AD114
OUTDOOR
FIRE BOWL
Copyright © 2008, Asia Direct, Inc., Norcross, GA
.
IMPORTANT!
Please read and follow ALL instructions
before assembling or using this product.
FOLLOW INSTRUCTIONS AND WARNINGS TO AVOID FIRE,
SERIOUS INJURY OR DEATH.
• Outdoor use only. Never use in enclosed area. Use in unventilated areas
will
endanger your life.
• Keep away from all combustible materials including gasoline and other
flammable
liquids and vapors.
• Use on a level, noncombustible surface only. Keep away from house,
garage,
balconies, or eave overhangs.
• Keep out of the reach of children.
• Be sure screen is in place while in use and do not use in windy conditions.
• Do not overfill firebox or use to burn leaves and trash.
• Exercise the same care you would with an open fire.
• Never leave unit unattended when hot or in use.
• Completely extinguish fire before leaving.
• Use gloves when handling or moving. Ashes can remain warm for a long
time
after extinguishing.
• Dispose of cold ashes properly.
• Do not modify in any way nor use with parts not expressly approved by manufacturer
Contact local authorities regarding possible burn restrictions before using product.
WARNING
STEP 1
Place Large Ring upside down (holes
facing up).
STEP 2
Place and lightly fasten each Leg to
Large Ring with Allen Bolt using Allen
Wrench. DO NOT FULLY TIGHTEN
THE BOLTS.
STEP 3
Insert Small Ring into U-shaped bracket
of each Leg. Lightly fasten each Leg with
Allen Bolt using Allen Wrench. DO NOT
FULLY TIGHTEN THE BOLTS.
STEP 4
Invert assembly so that Large Ring is on
top. Tighten all eight Allen Bolts securely at
this time.
STEP 5
Place Fire Bowl into Large Ring.
STEP 6
Attach handle to screen using supplied hardware. Place Screen onto
Fire Bowl as shown, using the recess in the bowl for alignment.
NOTE:
1. As with any burning appliance, periodic maintenance is required to return painted surfaces to original
appearance. When rust appears on painted surfaces, use sandpaper or steel brush to remove particles
and re-coat with paint intended for high-temperature surfaces. Select paint suitable for fireplace
maintenance and follow label directions on the paint.
2. Fire Pit surface will discolor after use. This is normal and expected.
Fire Bowl
(1 each)
Screen handle & hardware
(1 each)
Legs
(4 each)
Large Ring
(1 each)
Small Ring
(1 each)
Allen Wrench
(1 each)
Allen Bolts
(8 each)
Make sure you have all parts before beginning assembly (refer to the Parts Identification List below). If any parts listed below are damaged,
or are missing, please call customer service at 1-800-230-6530 (Monday through Friday 9:00 a.m. until 5:00 p.m. Eastern Standard Time), or
email us at [email protected].
Assembly Instructions
Parts Identification List
Copyright © 2008, Asia Direct, Inc., Norcross, GAModel #AD114
Screen Lifting Tool
(1 each)
Screen (1 each)
Vinyl Cover (Not Pictured)
(1 each)
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
NAPOLEON TQ2225 Owner's manual
-
Catalina Creations AD213C Operating instructions
-
Catalina Creations AD248 User manual
-
Matador Radiant User manual
-
Rankam SC2048701-SC Owner's manual
-
Sunnydaze Decor NB-SMS202 Operating instructions
-
One Stop Gardens 92771 Assembly Instructions Manual
-
Master Forge MFW784BDP Operating Instructions Manual
-
Unbranded CG2053904-RG Operating instructions
-
Catalina Creations AD389 Operating instructions
