Savant SHA-MGEIG200-00 Reference guide

Brand: Savant

Model: SHA-MGEIG200-00

Category: Networking

Type: Reference guide

This manual is also suitable for

Savant.com | 508.683.2500

Savant Shade and Provisioning and Programming Guide

SSC-002485 | SSC-W485 | SHA-MGEIGCTRL

Document Number: 009-1525-02

Document Date: June 2019

Document Supports: da Vinci 9.1

This document outlines the process of integrating Savant Shades into a Savant System. Details include:

– Provisioning Savant shade controllers to the local area network.

– Adding controllers to a Racepoint Blueprint Conﬁguration.

– Conﬁguring individual shade motors and motor groups.

– Filling out the Shade Data Table.

For information on how to wire Savant Shades, please refer to the Shade Wiring and Installation Guide.

2 of 30

Savant Shades Programming and Provisioning Guide

009-1525-02 | 190618

Contents

Important Information - Read First .......................................................................................................................................................................................3

1. Introduction ....................................................................................................................................................................................................................4

2. Deployment Checklist .................................................................................................................................................................................................5

3. Box Contents and Speciﬁcations ...........................................................................................................................................................................5

4. Status LED Descriptions ............................................................................................................................................................................................6

5 Provision the SSC-W485 Shade Controller (wireless) ....................................................................................................................................9

6 Provision the SSC-002485 Shade Controller (wired).....................................................................................................................................12

7 Provision the SHA-MGEIGCTRL Shade Controller (wired) ...........................................................................................................................13

8. Blueprint Conﬁguration (Adding Controllers) ...................................................................................................................................................14

8.1. Add Shade Controller .................................................................................................................................................................................................14

8.2. Add Shade Motor and Make Connections ..........................................................................................................................................................15

9. Blueprint Conﬁguration (Shade Manager) .........................................................................................................................................................16

9.1. Discover Shade Motors ...............................................................................................................................................................................................16

9.2. Conﬁgure Individual Motors .....................................................................................................................................................................................18

9.3. Create Shade Motor Groups ..................................................................................................................................................................................... 21

9.4. Sync Conﬁguration to the Shade Data Table .....................................................................................................................................................22

9.5. Save Conﬁguration, Generate Services, and Upload Conﬁguration .........................................................................................................23

10. Blueprint Conﬁguration (Shade Manager) .........................................................................................................................................................24

Appendix A: Network Requirements ....................................................................................................................................................................................25

Appendix B: Provision SSC-W485 .........................................................................................................................................................................................26

Appendix C: System Monitor ...................................................................................................................................................................................................28

Appendix D: Shade Data Table ...............................................................................................................................................................................................29

Important Notice ..........................................................................................................................................................................................................................30

3 of 30

Savant Shades Programming and Provisioning Guide

009-1525-02 | 190618

Important Safety Information - Read First

Before installing, conﬁguring, and operating Savant equipment and

other vendor equipment, Savant recommends that each dealer, installer,

etc. access and read all the required technical documentation. Savant

technical documentation can be located by visiting Savant.com. Vendor

documentation is supplied with the equipment.

Read and understand all safety instructions, cautions, and warnings in

this document and the labels on the equipment.

Safety Classiﬁcations In this Document

Note: Provides special information for installing,

conﬁguring, and operating the equipment.

IMPORTANT!

Provides special information that is critical

to installing, conﬁguring, and operating the

equipment.

CAUTION!

Provides special information for avoiding

situations that may cause damage to

equipment.

WARNING!

Provides special information for avoiding

situations that may cause physical danger to

the installer, end user, etc.

Electric Shock Prevention

ELECTRIC

SHOCK!

The source power poses an electric shock

hazard that has the potential to cause

serious injury to installers and end users.

ELECTRICAL

DISCONNECT

The source power outlet and power supply

input power sockets should be easily

accessible to disconnect power in the event

of an electrical hazard or malfunction.

Weight Injury Prevention

WEIGHT INJURY!

Installing some of the Savant equipment

requires two installers to ensure safe

handling during installation. Failure to

use two installers may result in injury.

Safety Statements

Follow all the safety instructions listed below and apply where relevant.

Additional safety information will be included where appropriate.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including ampliﬁers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type

plug. A polarized plug has two blades with one wider than the other.

A grounding type plug has two blades and a third grounding prong.

The wide blade or the third prong is provided for your safety. If the

provided plug does not ﬁt into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly

at plugs, convenience receptacles, and the point where they exit

from the apparatus.

11. Only use attachments/accessories speciﬁed by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table speciﬁed by

the manufacturer, or sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus combination to avoid

injury from tip over.

13. Unplug this apparatus during lightning storms or when unused for

long periods of time.

14. Refer all servicing to qualiﬁed service personnel. Servicing is

required when the apparatus has been damaged in any way, such

as power supply cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has been

dropped.

15. To completely disconnect this equipment from the AC mains,

disconnect the power supply cord plug from the AC receptacle.

4 of 30

Savant Shades Programming and Provisioning Guide

009-1525-02 | 190618

1. Introduction

This document will aid in guiding an integrator through the following:

– Provisioning the shade controller to the local network. Both the SSC-W485 (wireless) and SSC-002485 (wired) are covered.

– Adding Shade Motors to a Blueprint Conﬁguration.

– Conﬁguring and calibrate motors using the Shade Manager in Blueprint.

– Creating and Manage Shade Motor Groups.

It is important to read this guide in its entirety prior to beginning the process.

1.1. Required Items

Before starting the process, ensure that the following items are available and if required, installed into the system:

Savant Shades with Shade Motors Installed Using All Required Mounts.......................................................................................................................

Shade fabrics are installed onto shade tubes and installed in window ..........................................................................................................................

When multiple shade motors are installed, the 10-shade power panel (SHA-POW10-10) must be installed and wired .............................

When a single shade motor is installed, a single 24V DC power source must be wired into the system .........................................................

Unique ID (UID) of the shade controller (wired or wireless controller) ..........................................................................................................................

Unique ID is available on sticker on bottom of controller.

Savant Development Environment (SDE/Macbook®) ............................................................................................................................................................

Network meeting Savant Requirements .....................................................................................................................................................................................

See Appendix A: Network Requirements

SSID and Passphrase for Wi-Fi Router or Switch to local network ..................................................................................................................................

Optional:

Node ID (UID) of each motor and where that shade motor is installed is documented .........................................................................................

Node ID is available on stick on side of motor.

5 of 30

Savant Shades Programming and Provisioning Guide

009-1525-02 | 190618

2. Deployment Checklist

Verify all items in the Required Items checklist are installed and powered ..................................................................................................................

See Required items

Review the Status LED descriptions for SSC-W485, SSC-002485, and SHA-MGEIGCTRL ....................................................................................

See Status LED Descriptions

Provision the SmartControl RS-485 Shade Controller to the Network ..........................................................................................................................

See Provision the SSC-W485(wireless)

--OR--

See Provision the SSC-002485 (wired)

--OR--

See Provision the SHA-MGEIGCTRL (wired)

Add Shades to a RacePoint Blueprint Conﬁguration ............................................................................................................................................................

See Blueprint Conﬁguration (add controllers)

See Add Shade Motor and Make Connection

Savant Shades with Shade Motors Installed Using All Required Mounts.......................................................................................................................

See Discover Shade Motors

See Conﬁgure Individual Motors

See Create Shade Motor Groups (optional)

See Sync Conﬁguration to Shade Data Table

See Save Conﬁguration, Generate Services, and Upload to Host

3. Box Contents and Speciﬁcations

For Box Contents and Speciﬁcations, refer to the individual Quick Reference Guides (QRG) for each of the products used in the installation. Each QRG is

available on the Savant Customer community.

6 of 30

Savant Shades Programming and Provisioning Guide

009-1525-02 | 190618

4. Status LED Descriptions

The LED on the front of the shade controller indicates the state of the controller. Section 4.1 shows the LED sequencing for the dierent states of the

SSC-W485 wireless shade controller. Section 4.2 below describes the SSC-002485 wired shade controller. Section 3 Understanding the various LED states

assists a user when adding the shade controller to the Savant Pro System as well as helps to troubleshoot any problems that can happen.

4.1. Status LED Descriptions - SSC-W485 (wireless controller)

Reset Clears the network settings. Press and hold the reset button while powered until the Status LED begins blinking green

rapidly; then release. After the reset, the controller will be in Provisioning Mode. See Rapid Blink below.

O

No power applied. Power Supply may not be plugged in.

Solid Green

A solid green LED could indicate one of the two states below.

Normal Operation Mode. Controller was assigned an IP Address and is currently

communicating with the Savant Pro System Host.

Controller is communicating with the Savant Shade Manager in Blueprint.

Blinks Once

In Provisioning Mode and ready to be added to the local network. In this mode, no IP

Address is assigned.

Blinks Twice

Establishing connection with the local network.

Blinks Three

Times

During setup, the Blinks Three Times sequence indicates the shade controller was

provisioned to the local network and is trying to connect to the Savant Pro System Host.

During normal operation, the Blinks Three Times sequence can occur if communication

between the Shade Controller and Host is lost.

Short O Blink

Firmware is updating.

Rapid Blink

The reset button on the front panel was held down for at least ﬁve seconds and the

controller is performing a factory reset. After the reset, all network settings are cleared and

the factory defaults are restored.

7 of 30

Savant Shades Programming and Provisioning Guide

009-1525-02 | 190618

4.2. Status LED Descriptions - SSC-002485 (wired controller)

Reset Clears the network settings. Press and hold the reset button while powered until the Status LED begins blinking green rapidly; then

release. After the reset, the controller will be in Provisioning Mode. See Rapid Blink below.

O

No power applied. Power Supply may not be plugged in.

Solid Green

A solid green LED could indicate one of the two states below.

Normal Operation Mode. Controller was assigned an IP Address and is currently communicating

with the Savant Pro System Host.

Controller is communicating with the Savant Shade Manager in Blueprint.

Blinks Once

In Provisioning Mode and ready to be added to the local network. In this mode, no IP Address is

assigned.

Blinks Twice

Establishing connection with the local network.

Blinks Three

Times

During setup, the Blinks Three Times sequence indicates the shade controller was provisioned to

the local network and is trying to connect to the Savant Pro System Host.

During normal operation, the Blinks Three Times sequence can occur if communication between

the Shade Controller and Host is lost.

Short O Blink

Firmware is updating.

Rapid Blink

The reset button on the front panel was held down for at least ﬁve seconds and the controller

is performing a factory reset. After the reset, all network settings are cleared and the factory

defaults are restored.

8 of 30

Savant Shades Programming and Provisioning Guide

009-1525-02 | 190618

4.3. Status LED Descriptions - SHA-MGEIGCTRL (wired controller)

Reset Clears the network settings. Press and hold the reset button while powered until the Status LED begins blinking green rapidly;

then release.

O

No power applied. Power Supply may not be plugged in.

Link

Connection ready.

Act

BUS T4 is sending/receiving trac.

T4 packet BUS T4 is sending/receiving trac.

TD packet DIN BUS is sending/receiving trac.

Service Power and data have been supplied to the DMBM (DIN Module Building Management)

9 of 30

Savant Shades Programming and Provisioning Guide

009-1525-02 | 190618

5. Provision the SSC-W485 Shade Controller (wireless)

The SSC-W485 communicates with the Savant Host using Wi-Fi over a wireless network. Follow sections 5.1 through 5.5 to connect the shade controller to

the local network. Read sections 5.1 through 5.3 to understand the provisioning process. Follow sections 5.4 and 5.5 for instructions on how to provision the

shade controller.

5.1. Understanding the Network Provisioning Process

The diagram below demonstrates the provisioning process for the wireless SSC-W485 controller. Review the diagram for an understanding on how the

provisioning process works. If the shade controller on the network is the SSC-002485 wired type controller, skip this section and proceed to Section 6:

Provision the SSC-002485 Shade Controller (wired).

5.2. Provisioning Checklist

The following items are required to provision the SSC-W485 to the local network.

SSC-W485 wireless Shade Controller ..............................................................................................................................................................................

iOS Device with SmartConnrect App (v1.6 or higher) installed .............................................................................................................................

Network SSID and passphrase for the wireless router or switch in local network .........................................................................................

Unique ID (UID) of the SSC-W485 ....................................................................................................................................................................................

Optional: rpmEmbScanner ...................................................................................................................................................................................................

(Can obtain provisioning status of the controller)

1. The SmartConnect Application communicates with the SSC-W485

using Bluetooth signaling and provisions the controller to the local

network.

2. Once the controller is provisioned, it can communicate wirelessly

with the local network.

TIP! The SmartConnect Application only functions on the iOS

platform. Refer to Appendix B: Provision SSC-W485 Controller

using Embedded Web for information on provisioning without the

SmartConnect App.

5.3. SSID Guidelines

Maximum SSID Length Maximum Passphrase Length Wireless Standard Supported SSID and Passphrase special characters

32 characters WPA/WPA2 = 8-50 characters 802.11 a/b/g/n

(2.4 Ghz)

10 of 30

Savant Shades Programming and Provisioning Guide

009-1525-02 | 190618

5.4. Install SmartConnect

To connect the SSC-W485 controller to the network, the Savant SmartConnect application must be installed and running on an iOS device such as an

iPhone® or iPad®. The SmartConnect Application can be downloaded from the Apple App Store to your iPhone or iPad.

– From the Apple App Store search for Savant Systems LLC.

– Locate the SmartConnect App and download/install onto your iOS device.

For more information about the SmartConnect Application, refer to the SmartConnect Reference Guide (009-1046-xx) on the Savant Customer

Community.

HELPFUL INFORMATION!

SmartConnect v1.6 or higher is required to provision the SSC-W485.

– The iOS device running SmartConnect does not need to be connected to the network that the shade controller is going to be added to.

– The SmartConnect Application only functions on the iOS platform. Refer to Appendix B: Provision SSC-W485 Controller using Embedded Web for

information on provisioning without the SmartConnect App.

– During the provisioning process, ensure the controller is within 30 feet of the iOS device running the SmartConnect Application.

– Savant recommends using DHCP reservation. Refer to the Owners Manual for the local router for information on setting DHCP reservations.

– The iOS device that SmartConnect is running on must support Bluetooth v4.0.

– 802.11r (fast roaming) is not supported on the SSC-W485. If using a router that supports fast roaming, fast roaming should be disabled.

5.5. Provision the SSC-W485 Wireless Controller

1. Connect 24V DC to the 24V In connection on the rear of the SSC-W485 controller.

Note: The source of the 24V DC can vary depending on the number of shade

motors in the system. Savant recommends using either the SHA-POW10 power

panel or the SHA-POWSINGLE single shade power supply.

2. By default, a new SSC-W485 controller is set at the factory to be in provisioning mode. If

the Status LED is blinking green, skip this step (See Blinks Once from the table above).

If the LED is blinking a dierent sequence, follow the bulleted items below to set the

controller to provisioning mode.

– Press and hold the Reset Button for ﬁve seconds until the LED blinks green rapidly,

then release.

– After the reboot (1 – 2 seconds), the Status LED begins blinking green indicating

it is in provisioning mode and ready to be added to the local network (See Blinks

Once from the table above).

11 of 30

Savant Shades Programming and Provisioning Guide

009-1525-02 | 190618

3. On the iOS device, tap the SmartConnect (Connect) icon .

4. Locate the SSC-W485 in the Devices on Bluetooth section. Record the Savant ID (UID)

displayed. This UID will be used later in this procedure.

HELPFUL INFORMATION! When there is more than one SSC-W485 controller listed,

compare the UID displayed in SmartConnect with the UID on the label on bottom of

the controller.

5. Tap the SSC-W485 entry from the Devices on Bluetooth section of the App.

6. In the Pick a Network window that opens, tap Join Other Network… (image not shown)

7. Populate the Name ﬁeld with the SSID of the local Wi-Fi network.

–or-

Select the Use Current Network SSID ﬁeld. Select this ﬁeld only if the iOS device that the

SmartConnect App is running on is connected to the network the Savant Pro System is

communicating with (the iOS device must be connected to the local network for the Use

Current Network SSID option to work).

8. Tap Choose from the Security ﬁeld and select the security conﬁgured on the local network.

9. Enter the password to the local network into the Password ﬁeld.

10. Tap Join when complete.

11. A Provisioning Success window will open informing the user the device is provisioned.

HELPFUL INFORMATION!

– The SSC-W485 will now be listed in the Devices on WiFi section in SmartConnect.

– The iOS device must be connected to the same network as the shade controller for

the shade controller to be available in the Devices on WiFi section of SmartConnect.

– With the SSC-W485 now provisioned, the Status LED will blink one of the sequences

described below.

Blinks Three Times – The controller is connected to the local network and trying to connect to the Savant

Pro System Host. The SSC-W485 must be added to a Blueprint conﬁguration and the conﬁguration must be

uploaded to the Host. Follow the steps in the Blueprint Conﬁguration section below to do this.

Solid Green – The controller Is communicating with both the local network and with the Savant Pro System

Host. The conﬁguration running on the Host has this controller in its conﬁguration.

– If the IP Address of the controller is required (possibly for troubleshooting or to verify DHCP reservation), the IP Address for the SSC-W485 can

be discovered using the rpmEmbScanner utility from the Savant Application Manager on the SDE/MacBook. To open the utility, select Launch >

rpmEmbScanner from the menu bar in the Savant Application Manager (SAM).

12 of 30

Savant Shades Programming and Provisioning Guide

009-1525-02 | 190618

6. Provision the SSC-002485 Shade Controller (wired)

The SSC-002485 shade controller is a wired controller and does not need to be provisioned through SmartConnect. Follow section 6.1 below to connect the

shade controller to the local network.

6.1. Add SSC-002485 Shade Controller to the Local Network

1. Connect an RJ-45 Cat 5e/6/7 between the Ethernet port on the rear of the shade

controller and the local network router or switch.

2. Connect the included 12V DC power supply into a surge protected 120-240V AC

50/60Hz outlet.

3. Once the controller is powered, it will go through startup diagnostics and

automatically acquire an IP Address.

TIP! Savant recommends assigning IP address on the local network using DHCP

reservations through the router. This allows all addressing to be managed in

one location, and protects against addressing issues in the event of a power

outage.

4. Once an IP Address is assigned by the router, the status LED on the front panel

will blink twice indicating it has been assigned an IP Address and is trying to

connect to the Savant System Host. See Blinks Twice in table above for reference.

HELPFUL INFORMATION!

– A Solid Green Status LED indicates the Savant Host has a conﬁguration on it that includes this shade controller and the shade controller

is currently communicating with the Host. This process is described later in this document. For now, the LED will Blink Twice.

– If the IP Address of the controller is required (to troubleshooting or to verify DHCP reservation), the IP Address for the SSC-002485

can be discovered using the rpmEmbScanner utility in the Savant Application Manager on the SDE/MacBook. To open the utility, select

Launch > rpmEmbScanner from the menu bar of the Savant Application Manager (SAM).

13 of 30

Savant Shades Programming and Provisioning Guide

009-1525-02 | 190618

7. Provision the SHA-MGEIGCTRL shade controller

The SHA-MGEIGCTRL is a wired controller and does not need to be provisioned via SmartConnect. Follow the steps in section 7.1 below to connect the

shade controller to the network.

7.1. Add SHA-MGEIGCTRL Shade Controller to the Local Network

1. Connect an RJ-45 Cat 5e/6/7 between the Ethernet port on the shade

controller and the local network router or switch.

TE GND L H Vcc GND L H

Vcc

Expansion

DW UP

GND

LAN

LINK

ACT

T4 packet

TD packet

Service

Reset

RS-232 LAN

ON+

24V

1 2 3

H L GND

TD Bus

To SHA-PMOD5G

14 15 16 17 18 19 20 21 22 23 24 25

1 2 3 4 5 6 7 8 9 10 11 12 13

4 5 6

LAN Connection to

Router or Switch

24V DC

2. Wire the SHA-MGEIGCTRL to the SHA-PMOD5G as described in the

Shade Wiring and Installation Guide.

3. Once the controller is powered, it will go through startup diagnostics

and automatically acquire an IP Address.

TIP! Savant recommends that DHCP reservation be conﬁgured on

the router in the local network. Using this method sets a static IP

Address for each device ensuring the IP Addresses will not

change during a power outage.

4. Once an IP Address is assigned by the router, the Service LED on the

front panel will illuminate Solid Red indicating it has been assigned an

IP Address and is trying to connect to the Savant Pro System Host.

HELPFUL INFORMATION!

– A Flashing Red Service LED indicates the shade controller is

currently communicating with the Host.

– If the IP Address of the controller is required (to troubleshoot-

ing or to verify DHCP reservation), the IP Address needs to be

discovered using a Network Scanner.

14 of 30

Savant Shades Programming and Provisioning Guide

009-1525-02 | 190618

8. Blueprint Conﬁguration (Adding Controllers)

This section describes how to add the shade controller and shade motor into a Racepoint Blueprint conﬁguration.

8.1. Add Shade Controller

The process below is applicable for all controllers referenced in this guide.

1. Open Savant Application Manager (SAM) .

2. Through SAM, open a RacePoint Blueprint conﬁguration.

3. Select Show Library from the Blueprint toolbar to open the

Components library.

4. Search for the desired shade controller:

– SSC-W485 (wireless controller)

– SSC-002485 (wired controller)

– J Geiger Controller (SHA-MGEIGCTRL)

5. Drag the shade controller into either a shared equipment or user

zone.

HELPFUL INFORMATION! Placing a component in the Shared

Equipment zone ensures that it will be accessible from any zone

in the Savant Pro App. Placing a component in a user zone

limits its availability to that zone only.

6. In the window that opens, enter a unique name that describes the

component being added.

7. Select Create to add the controller.

8. Drag the shade controller from the component list to the layout

window.

9. Select Hide Library from the Blueprint toolbar to close the

component library.

10. Double-click the shade controller to open an Inspector window.

11. Enter the 16 character UID for the controller into the Savant UID

ﬁeld.

TIP! The UID can be obtained from a sticker located on the

bottom of the controller, or can be copy and pasted from

the rpmEmbeddedScanner or Shade Manager window.

12. Close the Inspector.

15 of 30

Savant Shades Programming and Provisioning Guide

009-1525-02 | 190618

8.2. Add Shade Motor and Make Connections

To add a shade motor to a Blueprint conﬁguration, do the following:

1. Open the Components library by selecting Show Library from the

Blueprint toolbar.

2. Search for the name of the desired shade controller into the search

bar.

3. Drag the shade into either a Shared Equipment or User zone.

HELPFUL INFORMATION! Placing a component in the Shared

Equipment zone ensures that it will be accessible from any zone

in the Savant Pro App. Placing a component in a user zone limits

its availability to that zone only.

4. In the window that opens, enter a unique name that describes the

component being added.

5. Select Create.

6. Drag the shade motor into the layout window.

7. Make the necessary connections in blueprint.

HELPFUL INFORMATION!

– Each RS485 control port supports up to 15 shade motors.

– Each controller can support up to 30 motors in total.

16 of 30

Savant Shades Programming and Provisioning Guide

009-1525-02 | 190618

9. Blueprint Conﬁguration (Shade Manager)

The Shade manager in Blueprint (Tools > Savant Shades) is used to discover, conﬁgure, and integrate Savant Shades into a Savant System. From the shade

manager, the following can be achieved:

– Discover each shade motor that is wired to the shade controller.

– Label each shade motor.

– Add each shade motor to a zone in the Blueprint conﬁguration.

– Change shade motor direction (standard or reverse).

– Adjust upper and lower limits to shade travel.

– Create Shade Groups and add motors to each group.

– Adjust the speed that the shades travel.

– Reset all data conﬁgured in the shade motors to factory default values.

9.1. Discover Shade Motors

With the shade controller added to Blueprint, the shade controller and shade motor can be discovered and conﬁgured.

1. Connect MacBook/SDE to the network that the shade controller is connected to.

2. From the Blueprint menu bar, select Tools > Savant Shades...

3. Select the Scan button from the Shade Manager window that opens. The Shade

Manager will scan the local network for all Savant Shade controllers.

IMPORTANT! For shade motors to be discovered, all components, including

motors and any shade power modules, must be installed and powered on.

Select Scan

4. Select the Stop… button once the shade controller(s) have discovered.

IMPORTANT! Once the Shade Manager connects to the shade controller,

the status LED on the shade controller will switch to solid green indicating

Blueprint is now communicating with controller. During this time, the Host

is not able to communicate with the shade controller.

5. Select the Connect button and the shade controller will search for any shade

motors that are connected to that controller. Depending on the number of shade

groups and shade motors conﬁgured in the system, the scan can take up to 10

minutes or more.

Select Stop

Select Connect

to Scan for

Shade Motors

17 of 30

Savant Shades Programming and Provisioning Guide

009-1525-02 | 190618

6. Each shade motor discovered will appear under the controller’s port.

7. When the discovery process completed, verify all the shade motors wired to the

controller are listed. In the image to the right, only one shade motor is wired to

the controller.

TIP! Select the Wink button to pulse the shade motor. Winking gives a user a

way to identify the shade motor’s physical location.

18 of 30

Savant Shades Programming and Provisioning Guide

009-1525-02 | 190618

9.2. Conﬁgure Individual Motors

Each shade motor that was discovered must be conﬁgured following the steps outlined below:

Deﬁning Motor Properties

1. Select one of the shade motors.

2. Enter a Name to identify the motor. The name is

automatically added to the Label ﬁeld in the Shade Data

Table. This label will be used to identify the individual

shade motor within the Savant Pro App interface once

the completed conﬁguration has been uploaded to the

Host.

3. Verify the Node ID labeled on the side of the shade

motor is displayed in the NodeID ﬁeld. This value is

automatically populated.

HELPFUL! The Address (1) ﬁeld in the Shade Data Table is

also automatically populated with the Node ID.

4. From the Savant Zone ﬁeld, select the zone where the

shade is installed. If the motor was conﬁgured to a

speciﬁc User zone, only that zone is available. For all

zones to be available in the drop-down menu, the shade

motor should be in a Shared Equipment zone.

HELPFUL! Each time changes are made to either the

Name or Savant Zone ﬁelds, the updated data must

be synced to the data table. See section 9.4 below

for further details.

5. Select the Upper Limit disclosure triangle to expand this

ﬁeld.

6. Select the Up

or Down button and verify the

shade moves in the correct direction.

–

Nudges the shade up or down approxi-

mately 1/16 inch.

–

Moves the shade up or down approxi-

mately 4 ½ inches.

19 of 30

Savant Shades Programming and Provisioning Guide

009-1525-02 | 190618

Set Shade Upper and Lower Limit

7. Using the Up buttons, set the upper limit of

shade travel.

IMPORTANT! Do not press these buttons in rapid

succession. Wait for the motor to stop before

pressing the buttons again.

8. Select Save Upper Limit button once the upper limit is

found.

9. Using the Down

buttons, set the lower limit of

shade travel.

10. Select Save Lower Limit button once the lower limit is

found. At this point the yellow circle beside the Upper/

Lower Limit ﬁeld will change to a green circle with a

check. This indicates the upper and lower limits are

programmed into the shade motor.

11. Test the shade travel by selecting the Test Upper and Test

Lower Limit buttons.

Additional Motor Properties Information

Once the shade motor is working correctly, set any additional properties as required. Refer to the information below when conﬁguring.

SSC-W485 and SSC-0022485 Controllers

Motor Direction

For SSC-002485 and SSC-W485 controllers,

modify the Motor Direction ﬁeld from

Standard to Reverse if shade is traveling in

the wrong direction.

Up/Down Speed Controls the speed of the shade motor.

Slow Speed Controls how fast the shade motor slows

down.

App Software Info Lists the version of ﬁrmware installed in the shade motor. The Savant Support Team may require this information when

troubleshooting a problem. The last six characters identify the version of ﬁrmware.

Using the App Software Info number from image above (91424D450009):

– The 45 is treated as a hex value so ﬁrst convert the hex value 0x45 into ASCII = E.

– Last four digits are treated as decimal so 00 09 is treated as 09.

– Therefore, the ﬁrmware version is E09 for this example.

20 of 30

Savant Shades Programming and Provisioning Guide

009-1525-02 | 190618

Software Info Lists the shade motor software version installed in the shade motor. The Savant Support Team may require this information

when troubleshooting a problem.

Serial Number Serial number of the shade motor. The ﬁrst six characters of the serial number are stamped on the shade as the Node ID.

Firmware Revision Lists the shade motor ﬁrmware version. The Savant Support Team may require this information when troubleshooting a

problem.

Factory Reset Resets the data stored in the shade motor to its factory default values. The reset can take up to 30 seconds and the motor may

pulse during the process. The following ﬁelds in the shade manager are reset when the Factory Reset button is selected:

– Upper/Lower Limits

– Motor Direction

– Up/Down Speed

– Shade Label.

HELPFUL INFORMATION

– If motor seems to be behaving erratically and is not responding to control commands; the motor may need to be factory

reset.

– Once reset, the colored circle

in the Upper/Lower Limit ﬁeld will switch to yellow indicating the shade motor is

currently set to its factory default values.

SHA-MGEIGCTRL Controller

Shade Label The label or value entered into this

ﬁeld is written to the ﬁrmware on the

shade motor. The label entered can be

used to keep track of shade motors in

the event the motors are changed or

swapped.

Soft Start The amount of time (in seconds) in which the motor moves slowly before accelerating to the Motor Speed.

Soft Stop The amount of time (in seconds) in which the motor moves slowly before stopping.

Obstacle Detection Disabled by default, this will stop the shade motor from rolling if the motor detects resistance. There are four levels.

– Level 1: If the motor detects an obstruction while moving up, the motor movement stops.

– Level 2: Obstructions detected when the motor is moving upwards and downwards will cause the motor to stop.

– Level 3: (Obstructions detected when the motor is moving up will stop the motor, down will cause the motor to move upwards.

– Level 4: Obstructions detected when the motor is moving up will cause the motor to move upwards, obstructions detected

downwards will cause it to stop.

Firmware Revision The ﬁrmware revision of the controller.

Hardware Revision The hardware revision of the controller.

Factory Reset This will restore the motor to factory defaults. Factory defaulting the unit will clear all settings and limits for the motor.

Page is loading ...

Savant SHA-MGEIG200-00 Reference guide

Brand: Savant

Model: SHA-MGEIG200-00

Category: Networking

Type: Reference guide

This manual is also suitable for

Download PDF

report

Savant SHA-MGEIG200-00 Reference guide

This manual is also suitable for

Savant SHA-MGEIG200-00 Reference guide

Related papers

Other documents