2. Promax
  3. SATHUNTER+
SATHUNTER+

Promax SATHUNTER+ Reference guide

  • Hello! I am an AI chatbot trained to assist you with the Promax SATHUNTER+ Reference guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What does the 'LOW BATTERY' message indicate?
    What does the 'LNB SHORT CIRCUIT' message mean?
    What does the 'LNB OVER CURRENT' message indicate?
    What does 'BATTERY MODE' signify?
    What does the 'NETWORK NOT FOUND' message indicate?
    What does the 'SERVICES NOT FOUND' message mean?
    What does the 'LNB NOT DETECTED' message indicate?
    How do I turn on the SATHUNTER+?
    How do I perform fine-tuning?
    How do I access the configuration menu?
QUICK REFERENCE GUIDE
SATHUNTER+
SCREEN ICONS REFERENCE
1
RF signal input
Detect
Identify
3
2
1
Trademark of the
DVB - Digital Video
Broadcasting Project
FRONT VIEW
4
5
6
4
USB connector
External power input 12 V
Adjust
18/13/OFF
S S2 DS
S S2 DS
USB
Manual Power Off.
USB connected to the PC.
Battery level
LNB power supply (13 V, 18 V or OFF).
22 kHz signal activated.
The DVB-S, DVB-S2 or DSS has not been synchronized.
The DVB-S, DVB-S2 or DSS has been synchronized.
Charging battery.
2
3
5
6
USER MANUAL
DOWNLOAD
Find the user’s manual on the download area at:
www.promaxelectronics.com
SATHUNTER+
PDF
SATHUNTER+
OPERATION
Turn on the SATHUNTER+ pressing , or for two seconds. If you press or
for more than five seconds, it starts in manual power off mode.
DETECTION
Plug the SATHUNTER+ to the antenna socket and turn the antenna until the SATHUNTER+ shows
the maximum power on the display.
Maximum measured
power
Current power
1)DETECT
18
MAX POWER RATE: 41%
POWER RATE: 40%
+
LNB Voltage
RF
When using the SATHUNTER+, it may appear on the display some messages and icons, depending
on the status or event is taking place. These messages and icons are detailed below:
“LOW BATTERY”
“VERY LOW BATTERY”
“LNB SHORT CIRCUIT”
“LNB OVER CURRENT”
“MANUAL POWER OFF”
“AUTO POWER OFF”
“BATTERY MODE”
“UPDATE MODE”
“NETWORK NOT FOUND”
“SERVICES NOT FOUND”
“LNB NOT DETECTED”
“FULL BATTERY”
“MPEG-2 NOT DETECTED”
“LOADING NETWORK”
“LOADING SERVICES”
“HIGH TEMPERATURE”
-
The equipment will be switched off automatically.
The LNB can be short circuit.
The LNB has a high consumption.
The instrument has to be switched off by hand.
The instrument will switched off after five minutes of inactivity.
-
-
-
-
Power level is below the minimum necessary to detect a LNB (this value can
be adjusted by software, usualy .
-
It is not detecting the Transport Stream signal MPEG-2.
-
-
The running temperature is too high. The equipment must be switched off for
a while. If the problem persist, contact with the technical support.
10%)
QUICK REFERENCE GUIDE
SATHUNTER+
IDENTIFICATION
PRESS IDENTIFY TO MOVE
TO THE NEXT STORED
TEST POINT.
PRESS IDENTIFY TO MOVE
TO THE NEXT STORED
TEST POINT.
PRESS
IDENTIFY.
PRESS
IDENTIFY.
Locked signal Standard
Test Point Name
and frequency
Sequential number of the test point
2)IDENTIFY 13 S2
TP64 FR: 1396.
0
MHz
13E Sky
Next HD
SKY Cinema HD
NationalGeo HD
NE T:
SE RVI C E LIS T : 3/ 8
TP04
++
Test point
frequency
2)IDENTIFY 13 S2
TP65 FR:
1799.0
MHz
4E8_EU
TVE Internacional
TV5 Monde Europe
NE T:
SE RVI C E LIS T : 3/ 4
TP05
RTL Television
++
RF
RF
Turned channel name
Services
QUICK REFERENCE GUIDE
Press and wait until locking the signal. The display will show the parameters of the
test point (name and frequency), the channel tuned and its services. To change to
another stored channel press again.
27-06-2016 (0 DG0078)
v1.0
SATHUNTER+
ADJUST
Press to perform fine-tuning. Check that every user's access point in the installation
is meeting the criteria established by current regulations. To measure another stored
Find the user’s manual on the download area at: www.promaxelectronics.com
CONFIGURATION
At the DETECTION screen, press and hold until appears the configuration menu.
ADJUST
TP0 HI30 FR:1779.4MHz
POWER: 54.7dBuV
LM: 9.0dB MER: 13.9dB
1.2E-5
<1.0E-8
CBER:
VBER:
0
10
13~ S
TP04
++
)SETUP
START SPECTRUM
SELECT MEASURE MER
SOUND CONTROL BEEP
BACKLIGHT MODE AUTO
CONTRAST LCD
18V
1)CANCEL 2)OPTION 3)SELECT
CO N FIRM & E X IT
Exits the configuration menu
without saving changes.
Scrolls along the menu options.
Changes the parameter / Accepts.
Start Spectrum: It starts the Spectrum Analyser.
Select Measure: Select measurement you want larger on the screen.
Confirm & Exit: It applies and saves the changes made and exits the configuration menu.
PRESS ADJUST FOR
THE NEXT TEST
POINT
PRESS ADJUST FOR
THE NEXT TEST
POINT
Locked signal
Test Point Name
PRESS
ADJUST
PRESS
ADJUST
Sequential number of the test point.
3)ADJUST
TP65 FR:1799.0 MHz
POWER: 54.7dBuV
MER:13.9dB LM: 9.0dB
1.2E-5
<1.0E-8
CBER:
VBER:
0
15
13 S2
TP05
++
Test point frequency
RF
Turn off the SATHUNTER+ by pressing or for three seconds.
QUICK REFERENCE GUIDE
channel, press again until finding the channel you are looking for. In case not
locking the signal, it shows the Signal to Noise Ratio (SNR).
/