Bosch PS82-02 User manual

1

IMPORTANT: IMPORTANT : IMPORTANTE:

Read Before Using Lire avant usage Leer antes de usar

For English Version Version française Versión en español

See page 2 Voir page 13 Ver la página 24

Operating/Safety Instructions

Consignes de sécurité/d’utilisation

Instrucciones de funcionamiento y seguridad

1-877-BOSCH99 (1-877-267-2499) www.boschtools.com

Call Toll Free for

Consumer Information

& Service Locations

Pour obtenir des informa-

tions et les adresses de nos

centres de

service après-vente,

appelez ce numéro gratuit

Llame gratis para

obtener información

para el consumidor y

ubicaciones de servicio

PS42

PS82

2610034966.indd 1 10/1/15 10:14 AM

2

Read all safety warnings and all instructions. Failure to follow the warn-

ings and instructions may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated (corded) power

tool or battery-operated (cordless) power tool.

Work area safety

Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the dust

or fumes.

Keep children and bystanders away while

operating a power tool. Distractions can

cause you to lose control.

Electrical safety

Power tool plugs must match the out-

let. Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) power tools. Unmodified plugs

and matching outlets will reduce risk of elec-

tric shock.

Avoid body contact with earthed or

grounded surfaces such as pipes, radia-

tors, ranges and refrigerators. There is an

increased risk of electric shock if your body is

earthed or grounded.

Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil,

sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric

shock.

When operating a power tool outdoors,

use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

If operating a power tool in a damp location

is unavoidable, use a Ground Fault Circuit

Interrupter (GFCI) protected supply. Use of

an GFCI reduces the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and

use common sense when operating a pow-

er tool. Do not use a power tool while you

are tired or under the influence of drugs,

alcohol or medication. A moment of inatten-

tion while operating power tools may result in

serious personal injury.

Use personal protective equipment. Al-

ways wear eye protection. Protective equip-

ment such as dust mask, non-skid safety

shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personal

injuries.

Prevent unintentional starting. Ensure the

switch is in the off-position before con-

necting to power source and / or battery

pack, picking up or carrying the tool. Carry-

ing power tools with your finger on the switch

or energizing power tools that have the switch

on invites accidents.

Remove any adjusting key or wrench be-

fore turning the power tool on. A wrench

or a key left attached to a rotating part of the

power tool may result in personal injury.

Do not overreach. Keep proper footing and

balance at all times. This enables better con-

trol of the power tool in unexpected situations.

Dress properly. Do not wear loose cloth-

ing or jewelry. Keep your hair, clothing

and gloves away from moving parts. Loose

clothes, jewelry or long hair can be caught in

moving parts.

If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used. Use of dust collection can reduce dust-

related hazards.

Power tool use and care

Do not force the power tool. Use the cor-

rect power tool for your application. The

correct power tool will do the job better and

safer at the rate for which it was designed.

Do not use the power tool if the switch

does not turn it on and off. Any power tool

that cannot be controlled with the switch is

dangerous and must be repaired.

General Power Tool Safety Warnings

2610034966.indd 2 10/1/15 10:14 AM

3

Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

Store idle power tools out of the reach of

children and do not allow persons unfa-

miliar with the power tool or these instruc-

tions to operate the power tool. Power tools

are dangerous in the hands of untrained us-

ers.

Maintain power tools. Check for misalign-

ment or binding of moving parts, breakage

of parts and any other condition that may

affect the power tool’s operation. If dam-

aged, have the power tool repaired before

use. Many accidents are caused by poorly

maintained power tools.

Keep cutting tools sharp and clean. Prop-

erly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

Use the power tool, accessories and tool

bits etc. in accordance with these instruc-

tions, taking into account the working con-

ditions and the work to be performed. Use

of the power tool for operations different from

those intended could result in a hazardous

situation.

Battery tool use and care

Recharge only with the charger specified

by the manufacturer. A charger that is suit-

able for one type of battery pack may create

a risk of fire when used with another battery

pack.

Use power tools only with specifically des-

ignated battery packs. Use of any other bat-

tery packs may create a risk of injury and fire.

When battery pack is not in use, keep it

away from other metal objects like paper

clips, coins, keys, nails, screws, or other

small metal objects, that can make a con-

nection from one terminal to another.

Shorting the battery terminals together may

cause burns or a fire.

Under abusive conditions, liquid may be

ejected from the battery; avoid contact.

If contact accidentally occurs, flush with

water. If liquid contacts eyes, additionally

seek medical help. Liquid ejected from the

battery may cause irritation or burns.

Service

Have your power tool serviced by a quali-

fied repair person using only identical re-

placement parts. This will ensure that the

safety of the power tool is maintained.

Safety Rules for Cordless Impact Drivers

Hold power tool by insulated gripping

surfaces, when performing an operation

where the fastener may contact hidden

wiring or its own cord. Fasteners contacting

a “live” wire may make exposed metal parts of

the power tool “live” and could give the opera-

tor an electric shock.

Use clamps or another practical way to

secure and support the workpiece to a

stable platform. Holding the work by hand or

against your body leaves it unstable and may

lead to loss of control.

Do not drill, fasten or break into existing

walls or other blind areas where electrical

wiring may exist. If this situation is unavoid-

able, disconnect all fuses or circuit breakers

feeding this worksite.

Always wear safety goggles or eye protec-

tion when using this tool.

Wear ear protectors when using the tool

for extended periods. Prolonged exposure to

high intensity noise can cause hearing loss.

Use thick cushioned gloves and limit the

exposure time by taking frequent rest peri-

ods. Vibration caused by hammer-drill action

may be harmful to your hands and arms.

Secure the material being fastened. Never

hold it in your hand or across your legs.

Unstable support can cause loss of control

and injury.

Avoid accidental starting. Be sure the for-

ward/reverse switch is in the off position

before inserting battery pack. Carrying ap-

pliances with your finger on the switch or in-

serting the battery pack into an appliance with

the switch on invites accidents.

Remove battery pack before changing ac-

cessories. Accidental starting may occur

because battery appliances with a battery in-

serted are in the operative condition.

Be prepared for a reaction torque when

2610034966.indd 3 10/1/15 10:14 AM

4

“seating” or removing a fastener. The

screwdriver housing may tend to twist in the

opposite direction of bit rotation when “seat-

ing” or removing a fastener depending on the

torque setting of the tool.

Do not use dull or damaged bits and ac-

cessories. When installing an accessory, in-

sert the shank of the bit well within the chuck.

Be sure the chuck has locked onto the bit cor-

rectly.

Do not run the tool while carrying it at your

side. A spinning bit could become entangled

with clothing and injury may result.

Place the tool onto the fastener only when

the screwdriver is switched off. Rotating

driver tools can slide off the fastener.

Do not use this tool as a drill. Tools equipped

with shut-off clutches are not designed for

drilling applications. The clutch can shut off

automatically and without warning.

Be careful when driving long screws –

there is a risk of sliding off the fastener

head depending on type of socket or bit

used. First test the run-down of a fastener and

pay attention during the screw driving process

to ensure you do not injure yourself if the tool

bit or socket slides off of the fastener.

Additional Safety Warnings

GFCI and personal protection devices like

electrician’s rubber gloves and footwear will

further enhance your personal safety.

Do not use AC only rated tools with a DC

power supply. While the tool may appear to

work, the electrical components of the AC

rated tool are likely to fail and create a hazard

to the operator.

Keep handles dry, clean and free from oil

and grease. Slippery hands cannot safely

control the power tool.

Develop a periodic maintenance schedule

for your tool. When cleaning a tool be care-

ful not to disassemble any portion of the

tool since internal wires may be misplaced

or pinched or safety guard return springs

may be improperly mounted. Certain clean-

ing agents such as gasoline, carbon tetrachlo-

ride, ammonia, etc. may damage plastic parts.

Ensure the switch is in the off position

before inserting battery pack. Inserting the

battery pack into power tools that have the

switch on invites accidents.

Some dust created by

power sanding, sawing,

grinding, drilling, and other construction

activities contains chemicals known to

cause cancer, birth defects or other repro-

ductive harm. Some examples of these

chemicals are:

• Lead from lead-based paints,

• Crystalline silica from bricks and cement and

other masonry products, and

• Arsenic and chromium from chemically-

treated lumber.

Your risk from these exposures varies, de-

pending on how often you do this type of work.

To reduce your exposure to these chemicals:

work in a well ventilated area, and work with

approved safety equipment, such as those

dust masks that are specially designed to filter

out microscopic particles.

2610034966.indd 4 10/1/15 10:14 AM

5

Symbols

IMPORTANT: Some of the following symbols may be used on your tool. Please study them and

learn their meaning. Proper interpretation of these symbols will allow you to operate the tool

better and safer.

Symbol Name Designation/Explanation

V Volts Voltage (potential)

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

kg Kilograms Weight

min Minutes Time

s Seconds Time

⌀

Diameter Size of drill bits, grinding wheels, etc.

n

0

No load speed Rotational speed, at no load

n Rated speed Maximum attainable speed

.../min Revolutions or reciprocation per min-

ute

Revolutions, strokes, surface speed, or-

bits etc. per minute

0 Off position Zero speed, zero torque...

1, 2, 3, ...

I, II, III,

Selector settings Speed, torque or position settings. Higher

number means greater speed

Infinitely variable selector with off Speed is increasing from 0 setting

Arrow Action in the direction of arrow

Alternating current Type or a characteristic of current

Direct current Type or a characteristic of current

Alternating or direct current Type or a characteristic of current

Class II construction Designates Double Insulated Construc-

tion tools.

Earthing terminal Grounding terminal

Warning symbol Alerts user to warning messages

Li-ion RBRC seal Designates Li-ion battery recycling pro-

gram

Ni-Cad RBRC seal Designates Ni-Cad battery recycling pro-

gram

Read manual symbol Alerts user to read manual

Wear eye protection symbol Alerts user to wear eye protection

2610034966.indd 5 10/1/15 10:14 AM

6

Symbols (continued)

IMPORTANT: Some of the following symbols may be used on your tool. Please study them and

learn their meaning. Proper interpretation of these symbols will allow you to operate the tool

better and safer.

This symbol designates that this tool is listed by Under-

writers Laboratories.

This symbol designates that this component is recog-

nized by Underwriters Laboratories.

This symbol designates that this tool is listed by Un-

derwriters Laboratories, to United States and Canadian

Standards.

This symbol designates that this tool is listed by the Cana-

dian Standards Association.

This symbol designates that this tool is listed by the Ca-

nadian Standards Association, to United States and Ca-

nadian Standards.

This symbol designates that this tool is listed by the In-

tertek Testing Services, to United States and Canadian

Standards.

This symbol designates that this tool complies to NOM

Mexican Standards.

2610034966.indd 6 10/1/15 10:14 AM

7

Functional Description and Specifications

Disconnect battery pack from tool before making any assembly, ad-

justments or changing accessories. Such preventive safety measures

reduce the risk of starting the tool accidentally.

Cordless Impact Driver

Fig. 1

VENTILATION

OPENINGS

VARIABLE SPEED

CONTROL INDICATOR

BUILT IN

WORK LIGHT

BATTERY CHARGE

STATUS INDICATOR

LIGHTS

VARIABLE SPEED

TRIGGER SWITCH

BATTERY PACK

BATTERY

RELEASE

TABS

RUBBERIZED

GRIP

FORWARD/REVERSING

LEVER & TRIGGER LOCK

WORK LIGHT ON/

OFF BUTTON

LOCKING

SLEEVE

BIT

VARIABLE SPEED

SELECTOR

Model number PS42

Voltage rating 10.8V/12V

MAX

No load speed n

0

0-1,200 / 0-2,600/min

Impact rate 0-3,100/min

Maximum Capacities:

Chuck size 1/4" Hex-shank with power groove

Battery Packs/Chargers

Please refer to the Charger Manual included with your tool.

NOTE: For tool specifications refer to the nameplate on your tool.

2610034966.indd 7 10/1/15 10:14 AM

8

Functional Description and Specifications

Disconnect battery pack from tool before making any assembly, ad-

justments or changing accessories. Such preventive safety measures

reduce the risk of starting the tool accidentally.

Cordless Impact Wrench

Fig. 1a

VENTILATION

OPENINGS

VARIABLE SPEED

CONTROL INDICATOR

BUILT IN

WORK LIGHT

BATTERY CHARGE

STATUS INDICATOR

LIGHTS

VARIABLE SPEED

TRIGGER SWITCH

BATTERY PACK

BATTERY

RELEASE

TABS

RUBBERIZED

GRIP

FORWARD/REVERSING

LEVER & TRIGGER LOCK

WORK LIGHT ON/

OFF BUTTON

OUTPUT

DRIVE

VARIABLE SPEED

SELECTOR

Model number PS82

Voltage rating 10.8V/12V

MAX

No load speed n

0

0-1,200 / 0-2,600/min

Impact rate 0-3,100/min

Maximum Capacities:

Output drive 3/8" Square drive

Battery Packs/Chargers

Please refer to the Charger Manual included with your tool.

NOTE: For tool specifications refer to the nameplate on your tool.

2610034966.indd 8 10/1/15 10:14 AM

9

Disconnect battery pack

from tool before making

any assembly, adjustments or changing

accessories. Such preventive safety mea-

sures reduce the risk of starting the tool acci-

dentally.

INSERTING AND REMOVING

ACCESSORIES

(Model PS42 only)

To avoid loss of control,

ensure bit is locked in

chuck by pulling on bit after it has been insert-

ed. The chuck accepts only standard 1/4”

hexagonal shank accessories with power

groove.

Your tool is equipped with a quick release

chuck. To insert an accessory, simply pull

locking sleeve forward, insert desired acces-

sory into chuck and release locking sleeve

(Fig. 2).

To remove an accessory, pull locking sleeve

forward and simply remove it from the chuck.

Do not use this tool as a drill. Tools equipped

with shut-off clutches are not designed for

drilling applications. The clutch can shut off

automatically and without warning. Attempt-

ing to restart drilling after shut-off has been

reached can cause the tool to twist out of your

hand until the clutch again reaches shut-off.

Do not attempt to insert quick-change type

drill bits into this chuck.

(Model PS82 only)

When using the 3/8” square drive, attach only

high quality impact ready accessories with the

proper size square drive designed for use with

impact wrenches. To install a socket, simply

push completely onto output drive (Fig. 3).

LOCKING

SLEEVE

OUTPUT

DRIVE

SOCKET

CHUCK

SCREWDRIVER

BIT

BIT HOLDER

Assembly

Fig. 2

Fig. 3

2610034966.indd 9 10/1/15 10:14 AM

10

INTENDED USE

This tool is intended for the fastening and

loosening of bolts, nuts and various threaded

fasteners. This tool is not intended for use as

a drill.

VARIABLE SPEED CONTROLLED

TRIGGER SWITCH

Your tool is equipped with a variable speed

trigger switch. The tool can be turned “ON” or

“OFF” by squeezing or releasing the trigger.

The speed can be adjusted from the minimum

to maximum nameplate RPM by the pressure

you apply to the trigger. Apply more pressure

to increase the speed and release pressure to

decrease speed (Fig. 1).

BRAKE

When the trigger switch is released it activates

the brake to stop the chuck quickly. This is es-

pecially useful in the repetitive driving and re-

moval of screws.

VARIABLE SPEED CONTROL

SELECTOR

The speed of the power tool can be adjusted

by toggling the variable speed control on the

top of the impact driver/wrench. The speed of

the impact driver/wrench is indicated by the

indicator lights on the top of the impact driver/

wrench located next to the variable speed

control selector button. The lowest speed set-

ting is indicated by one green LED light turned

and the hightest setting is indicated by both

green LED lights turning on (Fig. 1).

No-Load

Speed

Impact Rate

Setting 1 0-1200/min 0-2700/min

Setting 2 0-2600/min 0-3100/min

FORWARD/REVERSING

LEVER & TRIGGER LOCK

After tool use, lock trigger

in “OFF” position to help

prevent accidental starts and accidental dis-

charge.

Your tool is equipped with a forward/reversing

lever and trigger lock located above the trigger

(Fig. 4). This lever was designed for changing

rotation of the bit, and for locking the trigger in

an “OFF” position.

For forward rotation, (with chuck pointed away

from you) move the lever to the far left.

For reverse rotation move the lever to the far

right. To activate trigger lock move lever to the

center off position.

Do not change direction

of rotation until the tool

comes to a complete stop. Shifting during

rotation of the chuck can cause damage to the

tool.

BUILT IN WORK LIGHT

Your tool is also equipped with three work

lights for better visibility when driving. The

lights turn on when the trigger is pulled or

when the light button on the top of the drill is

activated. The light will automatically turn off

within 10 seconds after releasing the trigger

or may be turned off manually by pressing the

light button on the top of the drill (Fig. 5).

Operating Instructions

Fig. 4

WORK LIGHT ON/

OFF BUTTON

Fig. 5

2610034966.indd 10 10/1/15 10:14 AM

11

BATTERY CHARGE STATUS INDI-

CATOR LIGHTS

Your tool is equipped with charge status indi-

cator lights (Fig. 1). The indicator lights shows

the charge status of the battery for a few sec-

onds when the On/Off trigger is pressed half-

way or fully.

LED Capacity

Continuous lighting 3 x green > 2/3

Continuous lighting 2 x green > 1/3

Continuous lighting 1 x green < 1/3

Flashing light 1 x green reserve

INSERTING AND RELEASING

BATTERY PACK

Release battery pack from tool by pressing on

both sides of the battery release tabs and pull

downward (Fig. 6).

To insert battery, align battery and slide bat-

tery pack into tool until it locks into position.

Do not force.

If battery release tabs

are cracked or otherwise

damaged, do not insert into tool. Battery

can fall out during operation.

OPERATING TIPS

You will extend the life of your bits and do

neater work if you always put the bit in contact

with the work before pulling the trigger. Dur-

ing the oper a tion, hold the tool firmly and exert

light, steady pressure. Too much pressure at

low speed will stall the tool. Too little pressure

will keep the bit from cutting and cause excess

friction by sliding over the surface. This can be

damaging to both tool and bit.

DRIVING WITH VARIABLE SPEED

The technique is to start slowly, increasing the

speed as the screw runs down. Set the screw

snug ly by slowing to a stop. Prior to driving

screws, pilot and clearance holes should be

drilled.

Always hold the machine straight on the bolt

to be tightened.

The best method to determine the right im-

pacting/tightening duration is by means of a

trial. For small screws, the right impacting/

tightening duration can be reached in less

then 0.5 Sec. Therefore, work with low RPM

and switch the machine off immediately when

the screw is tight and the impacting sound can

be heard.

For screwing larger, longer wood screws into

hard material, pre-drilling is the best method.

TIGHTENING TORQUE

The tightening torque depends on the dura-

tion of the impacting/tightening action. The

largest tightening torque is achieved after ap-

proximately 6 to 10 Sec. impacting/tightening

action.

The torque build-up depends on the fol-

lowing factors:

• Hardness of the bolts/nuts.

• Type of washer (disk washer, spring wash-

er, seal).

• Hardness of the material to be joined.

• Lubricating effect at the surfaces of the

junction.

This leads to the following application cases:

Hard case: The joining of metal to metal

with a disk washer. The maximum torque is

reached after a relative short impacting/

tightening action.

Medium case: The joining of metal to metal

where spring ring washer, disk spring washer,

stud bolts or bolts/nuts with conical seats are

used.

Soft case: The joining of e.g. metal to wood or

insulation material.

For middle or soft joining cases, the maximum

tightening torque is less than for hard cases.

Therefore, a longer impacting/tightening ac-

tion is necessary to arrive at the maximum

tightening torque.

FASTENING WITH SCREWS

This procedure shown in (Fig. 7) will enable

you to fasten ma terials together with your tool

BATTERY

RELEASE

TABS

Fig. 6

2610034966.indd 11 10/1/15 10:14 AM

12

without stripping, splitting or separating the

material.

First, clamp the pieces together and drill the

first hole 2/3 the diam eter of the screw. If the

material is soft, drill only 2/3 the proper length.

If it is hard, drill the entire length.

Second, unclamp the pieces and drill the

second hole the same diameter as the screw

shank in the first or top piece of wood.

Third, if flat head screw is used, countersink

the hole to make the screw flush with the sur-

face. Then, simply apply even pressure when

driving the screw. The screw shank clearance

hole in the first piece allows the screw head to

pull the pieces tightly together.

RUNNING NUTS AND BOLTS

Variable speed control must be used with cau-

tion for driving nuts and bolts with socket set

attach ments. The technique is to start slowly,

increasing speed as the nut or bolt runs down.

Set the nut or bolt snugly by slowing the tool

to a stop. If this procedure is not followed, the

tool will have a tendency to torque or twist in

your hands when the nut or bolt seats.

1. Drill 2/3 diameter

and 2/3 of screw

length for soft ma-

terials, full length

for hard materials.

Apply a slight even

pressure when driv-

ing screws.

2. Drill same

diameter as

screw shank.

3. Countersink

same diam-

eter as screw

head.

Screw

FASTENING WITH

SCREWS

Fig. 7

Maintenance

SERVICE

NO USER SERVICE-

ABLE PARTS INSIDE.

Preventive maintenance performed by un-

au thorized personnel may result in mis-

placing of internal wires and components

which could cause serious hazard. We

recom mend that all tool service be performed

by a Bosch Factory Service Center or Autho-

rized Bosch Service Station. SERVICE MEN:

Disconnect tool and/or charger from power

source before servicing.

BATTERIES

Be alert for battery packs that are near-

ing their end of life. If you notice decreased

tool performance or significantly shorter run-

ning time between charges then it is time to

replace the battery pack. Failure to do so can

cause the tool to operate improperly or dam-

age the charger.

TOOL LUBRICATION

Your Bosch tool has been properly lubricated

and is ready for use.

MOTORS

The motor in your tool has been engineered for

many hours of dependable service. To main-

tain peak efficiency of the motor, we recom-

mend it be examined every six months. Only

a genuine Bosch replacement motor specially

designed for your tool should be used.

CLEANING

To avoid accidents, al-

ways disconnect the

tool and/or charger from the power supply

before cleaning. The tool may be cleaned

most effectively with com pressed dry air. Al-

ways wear safety goggles when cleaning

tools with compressed air.

Ventilation openings and switch levers must

be kept clean and free of foreign matter. Do

not attempt to clean by inserting pointed ob-

jects through opening.

Certain cleaning agents

and solvents damage

plastic parts. Some of these are: gasoline,

car bon tetrachloride, chlorinated cleaning sol-

vents, ammonia and household detergents

that contain ammonia.

2610034966.indd 12 10/1/15 10:14 AM

Page is loading ...

36

LIMITED WARRANTY OF BOSCH PORTABLE AND BENCHTOP POWER TOOLS

Robert Bosch Tool Corporation (“Seller”) warrants to the original purchaser only, that all BOSCH portable and benchtop power tools will be free from defects

in material or workmanship for a period of one year from date of purchase. SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited

Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall be the repair or replacement of parts, without charge, which are

defective in material or workmanship and which have not been misused, carelessly handled, or misrepaired by persons other than Seller or Authorized Service

Station. To make a claim under this Limited Warranty, you must return the complete portable or benchtop power tool product, transportation prepaid, to any

BOSCH Factory Service Center or Authorized Service Station. For Authorized BOSCH Power Tool Service Stations, please refer to your phone directory.

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH AS CIRCULAR SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW BLADES, SAND-

ING BELTS, GRINDING WHEELS AND OTHER RELATED ITEMS.

ANY IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE YEAR FROM DATE OF PURCHASE. SOME STATES IN THE U.S., SOME CANADIAN PRO V-

INCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF

PROFITS) ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S. AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLU-

SION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S.,

PROVINCE TO PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY.

THIS LIMITED WARRANTY APPLIES ONLY TO PORTABLE AND BENCHTOP ELECTRIC TOOLS SOLD WITHIN THE UNITED STATES OF AMERICA, CANADA AND

THE COMMONWEALTH OF PUERTO RICO. FOR WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT YOUR LOCAL BOSCH DEALER OR IMPORTER.

GARANTIE LIMITÉE DES OUTILS ÉLECTRIQUES PORTATIFS ET D’ÉTABLI BOSCH

Robert Bosch Tool Corporation (le « vendeur ») garantit à l’acheteur initial seulement que tous les outils électriques portatifs et d’établi BOSCH seront exempts

de vices de matériaux ou d’exécution pendant une période d’un an depuis la date d’achat. LA SEULE OBLIGATION DU VENDEUR ET LE SEUL RECOURS DE

L’ACHETEUR sous la présente garantie limitée, et en autant que la loi le permette sous toute garantie ou condition implicite qui en découlerait, sera l’obligation

de remplacer ou réparer gratuitement les pièces défectueuses matériellement ou comme fabrication, pourvu que lesdites défectuosités ne soient pas at-

tribuables à un usage abusif ou à quelque réparation bricolée par quelqu’un d’autre que le vendeur ou le personnel d’une station-service agréée. Pour présenter

une réclamation en vertu de cette garantie limitée, vous devez renvoyer l’outil électrique portatif ou d’établi complet, port payé, à tout centre de service agréé

ou centre de service usine. Veuillez consulter votre annuaire téléphonique pour les adresses.

LA PRÉSENTE GARANTIE NE S’APPLIQUE PAS AUX ACCESSOIRES TELS QUE LAMES DE SCIES CIRCULAIRES, MÈCHES DE PERCEUSES, FERS DE TOUPIES,

LAMES DE SCIES SAUTEUSES, COURROIES DE PONÇAGE, MEULES ET AUTRES ARTICLES DU GENRE.

TOUTE GARANTIE IMPLICITE SERA LIMITÉE COMME DURÉE À UN AN À COMPTER DE LA DATE D’ACHAT. CERTAINS ÉTATS AMÉRICAINS, CERTAINES PROV-

INCES CANADIENNES N’ADMETTANT PAS LE PRINCIPE DE LA LIMITATION DE LA DURÉE DES GARANTIES IMPLICITES, IL EST POSSIBLE QUE LES LIMITATIONS

CI-DESSUS NE S’APPLIQUENT PAS À VOTRE CAS.

EN AUCUN CAS LE VENDEUR NE SAURAIT ÊTRE TENU POUR RESPONSABLE DES INCIDENTS OU DOMMAGES INDIRECTS (INCLUANT, MAIS NE SE LIMITANT

PAS AUX PERTES DE PROFITS) CONSÉCUTIFS À LA VENTE OU L’USAGE DE CE PRODUIT. CERTAINS ÉTATS AMÉRICAINS ET CERTAINES PROVINCES CANA-

DIENNES N’ADMETTANT PAS LE PRINCIPE DE LA LIMITATION NI L’EXCLUSION DES DOMMAGES INDIRECTS ET CONSÉQUENTIELS, IL EST POSSIBLE QUE LES

LIMITATIONS OU EXCLUSIONS CI-DESSUS NE S’APPLIQUENT PAS À VOTRE CAS.

LA PRÉSENTE GARANTIE VOUS ACCORDE DES DROITS BIEN DÉTERMINÉS, Y COMPRIS POSSIBLEMENT CERTAINS DROITS VARIABLES DANS LES DIF-

FÉRENTS ÉTATS AMÉRICAINS, PROVINCES CANADIENNE ET DE PAYS À PAYS.

CETTE GARANTIE LIMITÉE NE S’APPLIQUE QU’AUX OUTILS ÉLECTRIQUES PORTATIFS ET D’ÉTABLI VENDUS AUX ÉTATS-UNIS D’AMÉRIQUE, AU CANADA ET

AU COMMONWEALTH DE PORTO RICO. POUR COUVERTURE DE GARANTIE DANS LES AUTRES PAYS, CONTACTEZ VOTRE IMPORTATEUR OU REVENDEUR

BOSCH LOCAL.

GARANTIA LIMITADA PARA HERRAMIENTAS MECANICAS PORTATILES Y PARA TABLERO DE BANCO BOSCH

Robert Bosch Tool Corporation (“el Vendedor”) garantiza, únicamente al comprador original, que todas las herramientas mecánicas portátiles y para tablero

de banco BOSCH estarán libres de defectos de material o de fabricación durante un período de un año a partir de la fecha de compra. LA UNICA OBLIGACION

DEL VENDEDOR Y EL RECURSO EXCLUSIVO QUE USTED TIENE bajo esta Garantía Limitada y, hasta donde la ley lo permita, bajo cualquier garantía o condición

implícita por ley, consistirá en la reparación o sustitución sin costo de las piezas que presenten defectos de material o de fabricación y que no hayan sido utiliza-

das inco rrectamente, manejadas descuidadamente o reparadas incorrectamente por personas que no sean el Vendedor o una Estación de servicio autorizada.

Para efectuar una reclamación bajo esta Garantía Limitada, usted debe devolver el producto, que consiste en la herramienta mecánica portátil o para tablero de

banco completa, con el transporte pagado, a cualquier Centro de servicio de fábrica o Estación de servicio autorizada. Para Estaciones de servicio autorizadas

de herramientas mecánicas BOSCH, por favor, consulte el directorio telefónico.

ESTA GARANTIA LIMITADA NO SE APLICA A ARTICULOS ACCESORIOS TALES COMO HOJAS PARA SIERRAS CIRCULARES, BROCAS PARA TALADROS, BRO-

CAS PARA FRESADORAS, HOJAS PARA SIERRAS DE VAIVEN, CORREAS PARA LIJAR, RUEDAS DE AMOLAR Y OTROS ARTICULOS RELACIONADOS.

TODAS LAS GARANTIAS IMPLICITAS TENDRAN UNA DURACION LIMITADA A UN AÑO A PARTIR DE LA FECHA DE COMPRA. ALGUNOS ESTADOS DE LOS EE.UU.

Y ALGUNAS PROVINCIAS CANADIENSES NO PERMITEN LIMITACIONES EN CUANTO A LA DURACION DE UNA GARANTIA IMPLICITA, POR LO QUE ES POSIBLE

QUE LA LIMITACION ANTERIOR NO SEA APLICABLE EN EL CASO DE USTED.

EL VENDEDOR NO SERA RESPONSABLE EN NINGUN CASO DE NINGUN DAÑO INCIDENTAL O EMERGENTE (INCLUYENDO PERO NO LIMITADO A RESPONSABI-

LIDAD POR PERDIDA DE BENEFICIOS) QUE SE PRODUZCA COMO CONSECUENCIA DE LA VENTA O UTILIZACION DE ESTE PRODUCTO. ALGUNOS ESTADOS

DE LOS EE.UU. Y ALGUNAS PROVINCIAS CANADIENSES NO PERMITEN LA EXCLUSION O LIMITACION DE LOS DAÑOS INCIDENTALES O EMERGENTES, POR

LO QUE ES POSIBLE QUE LA LIMITACION O EXCLUSION ANTERIOR NO SEA APLICABLE EN EL CASO DE USTED.

ESTA GARANTIA LIMITADA LE CONFIERE A USTED DERECHOS LEGALES ESPECIFICOS Y ES POSIBLE QUE USTED TAMBIEN TENGA OTROS DERECHOS QUE

VARIAN DE ESTADO A ESTADO EN LOS EE.UU., DE PROVINCIA A PROVINCIA EN CANADA Y DE UN PAIS A OTRO.

ESTA GARANTIA LIMITADA SE APLICA SOLAMENTE A HERRAMIENTAS ELECTRICAS PORTATILES Y PARA TABLERO DE BANCO VENDIDAS EN LOS ESTADOS

UNIDOS DE AMERICA, CANADA Y EL ESTADO LIBRE ASOCIADO DE PUERTO RICO. PARA COBERTURA DE GARANTIA EN OTROS PAISES, PONGASE EN CON-

TACTO CON SU DISTRIBUIDOR O IMPORTADOR LOCAL DE BOSCH.

Exportado por: Robert Bosch Tool Corporation Mt. Prospect, IL 60056-2230, E.U.A.

Importado en México por: Robert Bosch, S.A. de C.V., Calle Robert Bosch No. 405, Zona

Industrial, Toluca, Edo. de México, C.P. 50070, Tel. (722) 2792300

!2610034966!

2610034966 10/15

2610034966.indd 36 10/1/15 10:14 AM

Bosch PS82-02 User manual

This manual is also suitable for

Bosch PS82-02 User manual

in other languages

Related papers

Other documents