American Standard 2513.018 User manual

Brand: American Standard

Model: 2513.018

Type: User manual

This manual is also suitable for

M61

To Be Specied:

❏ Color: ❏ White

❏ Seat: Olsonite #95 open front seat less cover

❏ Seat: Church #9500C open front seat less cover

❏ Seat: Pressalit seats for American Standard,

open front seat with/without cover (thermoset

compound material).

❏ Alternate Seat:

❏ Flush Valve: Sloan Royal #110-3 (Top Spud)

Sloan Royal #144-3 (Back Spud)

❏ Alternate Flush Valve:

❏ Carrier Fitting (by others):

INSTANTO™ 3.5 GPF

ELONGATED FLUSH VALVE TOILET

VITREOUS CHINA

INSTANTO™ ELONGATED 3.5 GPF TOILET

• Elongated ush valve toilet

• Vitreous china

• Wall-mounted elongated bowl

• Blowout ush action

• Fully-glazed 2-5/8" trapway

• 1-1/2" inlet spud

• 100% factory ush tested

❏ 2512.010 Elongated bowl only, top spud

❏ 2511.012 Elongated bowl only, back spud

❏ 2513.018 Elongated bowl only, back spud

with Integral Seat

Component parts:

❏ 047007-0070A Inlet spud (furnished with bowl)

Nominal Dimensions:

660 x 356 x 381mm

(26" x 14" x 15")

Recommended working pressure–between

25 psi at valve when ushing and 80 psi static

Fixture only, less seat, bolt caps and ush valve

Blowout water closets are exempt from the 1.6

gallon per ush requirements of the National Energy

Policy Act. However, some state and local codes

do not allow the use of 3.5 gallons per ush toilets.

Check local codes.

Compliance Certications -

Meets or Exceeds the Following Specications:

• ASME A112.19.2 for Vitreous China Fixtures

BARRIER FREE

SEE REVERSE FOR ROUGHING-IN DIMENSIONS

Revised 4/07

MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES

AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USABLE

BUILDING FACILITIES - CHECK LOCAL CODES.

When installed so top of seat is 432 to 483mm (17" to 19") from the

finished floor.

M62

INSTANTO™ 3.5 GPF

ELONGATED FLUSH VALVE TOILET

VITREOUS CHINA

BARRIER FREE

2512.010

2511.012

470mm

(18-1/2)

660mm

(26)

C/L OF SEAT POST HOLES

140mm

(5-1/2) CENTERS

292mm

(11-1/2)

14mm

(9/16)

76mm

(3)

133mm

(5-1/4)

356mm

(14)

318mm

(12-1/2)

229mm

(9)

98mm

(3-7/8)

70mm

(2- 3/4)

C/L OF FLUSH VALVE

38mm

(1-1/2)

FINISHED FLOOR

381mm

(15)

1-1/2 SPUD

159mm

(6-1/4)

298mm

(11-3/4)

121mm

(4-3/4)

1" N.P.T. OR C.W.T.

SUPPLY TO

FLUSH VALVE

(3) 25mm (1) DIA.

HOLES FOR

CARRIER STUDS

C/L OF OUTLET

673mm

(26-1/2)

6mm

(1/4)

FINISHED WALL

381mm

(15)

159mm

(6-1/4)

695mm

(27-3/8)

FINISHED

FLOOR

298mm

(11-3/4)

17mm

(11/16)

133mm

(5-1/4)

98mm

(3-7/8)

79mm

(3-1/8)

FINISHED

WALL

470mm

(18-1/2)

C/L OF SEAT POST HOLES

140mm (5-1/2) CENTERS

581mm

(22-7/8)

356mm

(14)

C/L

38mm (1-1/2) DIA. HOLE IN WALL

95mm

(3-3/4)

FOR WALLS UP TO 25mm (1") IN THICKNESS;

FOR EACH 25mm (INCH) ADDITIONAL THICKNESS

OF WALL ADD 25mm (1") TO THIS DIMENSION

121mm

(4-3/4)

254mm

(10)

16mm

(1-5/8)

38mm

(1-1/2)

102mm

(4)

(3) 78mm (1) DIA. HOLES

FOR CARRIER STUDS

C/L OF 1" C.W.T. OR N.P.T. SUPPLY

AS REQ'D TO FLUSH VALVE

INLET

38mm

(1-1/2)

298mm

(11-3/4)

127mm

(5)

286mm

(11-1/4)

114mm

(4-1/2)

114mm

(4-1/2)

C/L OF

OUTLET

76mm (3) DIA. HOLE

IN WALL FOR 1-1/2" SPUD

NOTES:

WASTE OUTLET SEAL RING MUST BE NEOPRENE OR GRAPHITE-

FELT (WAX RING NOT RECOMMENDED).

TO COMPLY WITH AREA CODE GOVERNING THE HEIGHT OF VACUUM

BREAKER ON FLUSH VALVE, THE PLUMBER MUST VERIFY

DIMENSIONS SHOWN FOR SUPPLY ROUGHING.

SUGGEST 1/16" CLEARANCE BETWEEN FACE OF WALL AND BACK OF

BOWL.

METHOD AND MEANS OF SUPPORT TO BE FIGURED AND FURNISHED

BY OTHERS.

FLUSH VALVE NOT INCLUDED WITH FIXTURE AND MUST BE

ORDERED SEPARATELY.

PLUMBER NOTE: PROVIDE SUITABLE REINFORCEMENT FOR ALL

SUPPORTS.

IMPORTANT: Dimensions of xtures are nominal and may vary within

the range of tolerances established by ANSI Standard A112.19.2. These

measurements are subject to change or cancellation. No responsibility is

assumed for use of superseded or voided pages.

Revised 5/06

American Standard 2513.018 User manual

Brand: American Standard

Model: 2513.018

Type: User manual

This manual is also suitable for

Download PDF

report

American Standard 2513.018 User manual

This manual is also suitable for

American Standard 2513.018 User manual

Related papers

Other documents