SATO 400E User manual

PN 9001135A

XL400e / XL410e

Printers

OPERATOR MANUAL

SATO UK Limited

Valley Road, Harwich

Essex CO12 4RR

Tel: 01255 240000

Fax: 01255 240111

Tech Support Hotline: 01255 252828

Email: [email protected]

www.satouk.com

SATO UK Limited

Warning: This equipment complies with the requirements in Part 15 of FCC rules for

a Class A computing device. Operation of this equipment in a residential area may

cause unacceptable interference to radio and TV reception requiring the operator to

take whatever steps are necessary to correct the interference.

parties in any form whatsoever without the express permission of SATO America, Inc.

The materials in this document is provided for general information and is subject to

change without notice. SATO America, Inc. assumes no responibilities for any errors

that may appear.

parties in any form whatsoever without the express permission of Sato UK Ltd. The

information provided in this document is for general purpose only and is subject to

change without prior notice. Sato UK Ltd. assumes no responsibilities for any errors

that may appear.

PN 9001135A

TABLE OF CONTENTS

INTRODUCTION

About This Manual 1-2

General Description 1-3

Control Features 1-4

TECHNICAL DATA

Physical Characteristics 2-2

Enviromental 2-2

Power 2-2

Processing 2-2

Print 2-2

Sensing 2-2

Media 2-3

Character Font Capabilities 2-3

Barcode Capabilities 2-4

Interface Modules 2-4

Regulatory Approvals 2-4

INSTALLATION

Unpacking & Parts Identification 3-2

Printer Installation 3-3

Site Location 3-3

Media Selection 3-3

Media Loading 3-4

Ribbon Loading 3-7

Interface Selection 3-12

RS232 Serial Interface 3-12

IEEE1284 Parallel Interface 3-14

Universal Serial BUS (USB) Adapter 3-15

Local Area Network (LAN) Ethernet 3-15

802.11B Wireless 3-15

Receive Buffer 3-16

ACK/NAK Protocol 3-16

Accessories Installation 3-17

PCMCIA Memory Upgrade 3-17

Stacker Unit 3-18

PN 9001135A

OPERATION

Printer Configuration 4-2

Dip Switch Panels 4-2

Configuration Modes 4-6

Normal Mode 4-6

Test Print Mode 4-7

Advanced Mode 4-8

Default Settings Mode 4-9

Flash Memory Download Mode 4-10

User Download Mode 4-12

Hex Dump Mode 4-13

Card Mode 4-14

Non-Standard Clear Mode 4-15

Service Mode - Test Print 4-16

Service Mode - Sensor Level 4-17

Service Mode - Pitch Offset 4-18

Service Mode - Cut Offset 4-19

Service Mode - Backfeed Offset 4-20

Service Mode - Counter Display 4-21

Screen Identification 4-22

Operational Adjustments 4-26

Darkness, Cut Position, Print Position, Display 4-26

Cutter Sensor Positioning 4-28

Operator Panel 4-29

Printing 4-30

Test Printing 4-30

Reloading Media 4-30

Powering Off 4-30

TROUBLESHOOTING

Error Signals 5-2

Printer Troubleshooting 5-3

Interface Troubleshooting 5-5

Parallel Interface 5-5

RS232 Serial Interface 5-5

LAN Ethernet Interface 5-6

Universal Serial Bus (USB) Interface 5-6

Performance Testing 5-7

Test Print Troubleshooting 5-9

Sensor Locations 5-12

PN 9001135A

MAINTENANCE

Cleaning Procedures 6-2

Replacement Procedures 6-3

Fuse 6-3

Print Head 6-4

Ribbon Roller 6-5

Adjustment Procedures 6-6

Print Head Balance 6-7

Print Head Alignment 6-8

Pressure Roller Alignment 6-9

Pressure Roller Balance 6-10

Ribbon Guide Adjustment 6-11

Ribbon Spindle Tensioning 6-12

Pitch Sensor Adjustment (Label Gap & Center Hole Media) 6-13

Pitch Sensor Adjustment (Eye-Mark Media) 6-14

Pitch Sensor Adjustment (R-Corner) 6-16

Pitch Sensor Adjustment (Side Hole Media) 6-17

Jump Hole Sensor Adjustment 6-18

Ribbon Sensor Adjustment 6-19

Cutter Sensor Adjustment 6-20

PN 9001135A

SATO XL400-410e Operator Manual PN 9001135A Page 1-1

INTRODUCTION

• About This Manual

• General Description

• Control Features

Unit 1: Introduction

SATO XL400-410e Operator Manual PN 9001135A Page 1-2

ABOUT THIS MANUAL

This manual is laid out consistent with the product discussed and provides all of the information

required for general printer configuration, operation, troubleshooting, and maintenance. For

specialized programming, refer to the Programming Manual provided with the product.

Step-by-step maintenance instructions are provided with typical problems and solutions. Become

familiar with each section before installing and maintaining the printer.

This manual also incorporates the use of special information boxes. Examples of these boxes

and the type of information provided in each, are below.

A comprehensive Table Of Contents provided at the front of this manual facilitates rapid

movement within. The contents identify the different Units, Chapters, and Sections. Each

references the page number of their commencement.

The pages of this manual have embedded headers and footers to assist the user in identifying

his or her exact position within the manual. The header provides the unit number followed by its

name. The footer identifies the product on the left, the manual’s part number in the center, and

the page number to the right side of the page.

Page enumeration is two-part with each separated by a hyphen. The first character set

references the Unit and the second identifies the page number. Page numbers begin with the

numeral (1) one at the commencement of a new unit and ascends sequentially.

WARNING: PROVIDES INFORMATION THAT, IF UNHEEDED, MAY

RESULT IN PRESONAL INJURY.

CAUTION: PROVIDES INFORMATION THAT, IF UNHEEDED, MAY

RESULT IN EQUIPMENT DAMAGE.

NOTE: Provides helpful hints to assist in performing the tasks at hand.

LCD DISPLAY: Provides the specific display that should be visible on

the LCD at that point.

Unit 1: Introduction

SATO XL400-410e Operator Manual PN 9001135A Page 1-3

GENERAL DESCRIPTION

The XL400/410 “e” series printers are complete, high-performance labeling systems designed

specifically for printing labels and tags. All printer parameters are programmable using the front

panel controls and dip switches to provide printing of all popular bar codes and fonts styles and

sizes.

Figure 1-1a, Primary Components

Figure 1-1b, Primary Components

Media Supply Spindle

Ribbon Unwind SpindleRibbon Rewind Spindle

Media Retaining Plate

Head Latch Lever

Operator PanelCutter Assembly

Print Head Assembly

Top Housing Cover

Adjustment Panel

Media Hold-Down

A/C Power Connector

Power Switch

External Fuse

Unit 1: Introduction

SATO XL400-410e Operator Manual PN 9001135A Page 1-4

CONTROL FEATURES

Figure 1-2a, Control Features

BUTTONS & SWITCHES

POWER Two position on/off switch that controls power flow to the system.

START / STOP Toggles the printer on/off line.

FEED Allows feeding of one tag or label each time it is pressed. Is only

functional when the printer is off-line. Feeds one label when the

cutter is disabled. Feeds one label, cuts, and backfeeds when the

cutter is enabled.

CUTTER ON/OFF Enables or disables the cutter. Is only functional when the printer is

off-line.

EJECT Feeds out any printed media. If the cutter is enabled; it feeds, cuts,

and backfeeds. If cutter is disabled; it ejects, cuts, and backfeeds.

MEDIA TYPE Allows the selection of the applicable media to be printed.

DSW1 & DSW2 Used to configure RS232 interface. Located behind access panel

inside the printer.

DSW3 Is largely reserved. Located behind access panel inside the printer.

VR4

VR3

VR2

VR1

DSW 1

DSW 2

DSW 3

DARKNESS

CUT

POSITION

PRINT

POSITION

DISPLAY

Potentiometers Dip Switches

Reference Label

Unit 1: Introduction

SATO XL400-410e Operator Manual PN 9001135A Page 1-5

Figure 1-2b, Control Features

Figure 1-3, Connection Ports

CONNECTION PORTS

AC Power Input Connector permits 115V, 50/60 Hz supply via supplied cord.

Interface Port Connector for interface harness. Must be connected for the printer to

be operational. Acceptable interface types are:

• RS232C Serial I/F Module, DB-25

• Parallel

• Universal Serial Bus Adapter

• Ethernet 10/100 BaseT I/F Module

• RS422/485 I/F Module, DB-9

Ext. Interface Port Connector for external control of print cycle. Also supplies power for

optional accessories - AMP 57-60140

Memory Card Slot Slot for the insertion of optional PCMCIA Memory Card

LCD Display

ON LINE

START

/STOP

FEED EJECT MEDIA TYPE

ERROR

CUTTER

ON/OFF

LED’s

Function Keys

SATO XL Printer

Accessory Port

Serial Interface Port

Memory Card Slot

Interface Port

Unit 1: Introduction

SATO XL400-410e Operator Manual PN 9001135A Page 1-6

SATO XL400-410e Operator Manual PN 9001135A Page 2-1

TECHNICAL DATA

• Physical Charcteristics

• Enviromental

•Power

• Processing

•Print

• Sensing

•Media

• Character Font Capabilities

• Barcode Capabilities

• Interface Modules

• Regulatory Approvals

Unit 2: Technical Data

SATO XL400-410e Operator Manual PN 9001135A Page 2-2

PHYSICAL CHARACTERISTICS

Width 19.6 Inches (302 mm)

Height 11.50 Inches (294 mm)

Depth 11.80 Inches (552 mm)

Weight 30.80 Pounds (14.0 Kg) standard

ENVIRONMENTAL

Operating Temperature 41° to 104°F (5° to 40°C)

Storage Temperature 0° to 104°F (-20° to 40°C)

Storage Humidity Max 90% RH, Non-Condensing

Operating Humidity 15 to 85% RH, Non-Condensing

Electrostatic Discharge 8kV

POWER

Input Voltage 115/220 Volts AC +/- 10%, 50/60 Hertz +/-1%

Power Consumption 150 Watts Operating

PROCESSING

CPU 32 Bit RISC

FLash ROM 2 Mega-Bytes

SDRAM 16 Mega-Bytes

Receive Buffer 2.95 Mega-Bytes

Memory Expansion See Options and Accessories

PRINT

Method Direct Thermal / Thermal Transfer

Speed (user selectable) 2, 3, 4, 5, 6 Inches Per Second

Print Module (dot size) .0049 Inches (.125 mm)

Resolution XL400e: 203 Dots Per Inch (8 dpmm)

XL410e: 305 Dots Per Inch (12 dpmm)

Maximum Print Width 4.4 Inches (112 mm)

Maximum Print Length 14.0 Inches (355 mm)

SENSING

Gap Fixed

Reflective Eye-Mark Fixed

Continuous Form Sensor not used.

Unit 2: Technical Data

SATO XL400-410e Operator Manual PN 9001135A Page 2-3

MEDIA

Eye-Mark Label Dimensions

Width: 1.26 to 3.94 Inches (32-100mm)