2. Computers & electronics
  3. Telecom & navigation
  4. Telephones
  5. Aiphone
  6. GT-TLI

Aiphone GT-TLI Specification

  • Hello! I am an AI chatbot trained to assist you with the Aiphone GT-TLI Specification. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
GT-TLI
Installation / Operation Instructions
This is the installation and operation manual for the GT-TLI only. Refer to the GT Series Installation
and Operation Manual for complete information on all other GT components.
1012
Telephone Line Interface for the GT Series
ATTENTION:
Precautions
! WARNING
(Negligence could result in death or serious injury to people.)
2 | GT-TLI Installation / Operation Instructions
• High voltage is present internally. Do not open the case. Electric shock may occur.
• Do not dismantle or alter the unit. Fire or electric shock may occur.
• Donotconnectanynon-speciedpowersourcetothe+,-terminalsanddonotinstalltwopowersuppliesin
paralleltoasingleinput.Fire,damagetotheunit,orsystemmalfunctionmayoccur.
• Keeptheunitawayfromwateroranyotherliquid.Fireorelectricshockmayoccur.
• Do not put any metal or paper into the unit through the openings. Fire of electric shock may occur.
• Donotplugorunplugwithwethands.Electricshockmayoccur.
• KeepACplugawayfrommoistureordustasremayoccur.
• KeepACcordfrombeingmarredorcrushed.IftheACcordisdamaged,reorelectricshockcouldoccur.
• Donotuseapowersupplywithavoltageotherthanspecied.Fireorelectricshockmayoccur.
• InsertACplugcompletelyandsecurelyintoACoutlet.Otherwise,reorelectricshockmayoccur.
• Donotinstalloruseneargasesorammablematerials.Fireorexplosionmayoccur.
! CAUTION
(Negligence could result in injury to people or damage to property.)
• Beforeturningonpower,makesurewiresarenotcrossedorshorted.Fireorelectricshockmayoccur.
• Whenmountingtheunitonwall,installtheunitinaconvenientlocation,butnotwhereitcouldbejarred
orbumped.Injurymayoccur.
• Donotinstallormakeanywireterminationswhilepowersupplyispluggedin.Itcouldresultinelectricshock
or damage to the unit.
• Donotinstalltheunitinanyofthefollowinglocations.Fire,electricshock,orunittroublemayoccur.
-Placesunderdirectsunlight,ornearheatingequipmentthatvariesintemperature.
-Placessubjecttodust,oil,chemicals,hydrogensulde(hotspring).
-Placessubjecttomoistureandhumidityextremes,suchasbathrooms,cellars,greenhouses,etc.
-Placeswheretemperatureisquitelow,suchasinsidearefrigeratedareaorinfrontofanairconditioner.
-Placessubjecttosteamorsmoke(nearheatingorcookingsurfaces).
-Placeswherenoisegeneratingdevicessuchasdimmerswitchesorinvertorelectricalappliances,areclose.
• Onproductswithgroundterminals,connecttoanearthground.Fireormalfunctionmayoccurifunitisnot
properly grounded.
• ForDCpowersystems,useAiphonepowersupplymodelspeciedwiththesystem.Ifnon-speciedproductis
used,reormalfunctionmayoccur.
• Do not place anything on top of unit. Fire or unit malfunction may occur.
• Donotmounttheunitinaplacesubjectedtoconstantvibrationorimpact.Ifjarredorknockedoffthewall,
injurymayoccur.
GENERAL PRECAUTIONS
• Allunits,exceptforthedoorstation,aredesignedforindooruseonly.Donotuseoutdoors.
• Inareaswherebroadcastingstationantennasarecloseby,theintercomsystemmaybeaffected
byradiofrequencyinterference.
• Ifacellularphoneisusedcloseby,theunitmaymalfunction.
• Thisproduct,beingacontrolunitfordoorrelease,shouldnotbeusedasacrimepreventiondevice.
• Keeptheunitmorethan3feetawayfromradioorTVset.
• Duetotheenvironmentalsoundaroundtheunit,itmayhindersmoothcommunication.Thisisnotamalfunction.
• Installation / Operation Instructions
• GT-TLI
• RJ11 cable
Wiring
Installation
AworkingGTsystemwithatleastoneentrypanelisrequiredwhenusingtheGT-TLItelephonelineinterfaceadaptor.
TheGT-TLIcanbedeskmountedorwallmountedusingthemountingslotsonthebackoftheunit.Ensurethatthe
mounting location is accessible.
3
Package Contents
R2
R1
NO C NC R1 R2CO TEL 12-24V
+
-
12-24VAC/DC
GT Bus Line
To Local Telephone
From Phone Line
GT-TLI
EL-12S
13 /16"
3-9/16"
1-1/8"
Secondary Dry Contact
PT
Specications
COLINE: Totelephoneline(RJ11)
TEL: ToInternalhousetelephone(RJ11)
12-24VAC/DC:Topowersupply12VAC/DC-0.5A,24VAC/DC-0.3A
R1/R2: To R1/R2 audio bus of GT system
NO/C/NC: 12VDC-2A,24VDC-1A
4 | GT-TLI Installation / Operation Instructions
Below are a few examples of connecting the GT-TLI to an existing telephone installation.
Wiring (continued)
Basic Connection
CO TEL
From Phone Line
CO TEL
CO TEL
PBX
Analog Port
CO Line
SETTING
1
4
GHI
7
PQRS
#0
ABC
JKL
TUV
5
8
2
6
9
WXYZ
MNO
3
DEF
TRANSFERPRIVACY HOLDSETTING
1
4
GHI
7
PQRS
#0
ABC
JKL
TUV
5
8
2
6
9
WXYZ
MNO
3
DEF
TRANSFERPRIVACY HOLDSETTING
1
4
GHI
7
PQRS
#0
ABC
JKL
TUV
5
8
2
6
9
WXYZ
MNO
3
DEF
TRANSFERPRIVACY HOLD
Note:
GT-TLI supports a maximum
of 3 telephone sets.
PBX Connection
3 Telephone Connection
From Phone Line
Linking GT-TLI to GT system
Direct Select / Push Button Entrance Station Addressing
Step 1:
Remove front cover from entrance station.
Step 2:
Toenterprogrammingmode,useasmallscrewdrivertopushandreleasebuttonundertherubbercaponfront
ofspeakermodule(GT-DA-L).TheamberLEDwillbeginashing,thenremainlit.Oncelit,theentrypanelisin
programming mode.
Step 3:
AtGT-TLI,pressthePROGbutton.TheGT-TLIisnowconnectedtotheentrancepanel.
Step 4:
Push and release the desired Call Button on the entrance station to assign the button to the GT-TLI station that is
active.Abliptonewillbeplayed.
Step 5:
AtGT-TLI,pressthePROG button to complete programming.
Step 6:
Toexitprogramming,pushthebuttonundertherubbercapontheGT-DA-LmoduleagainandtheamberLEDwill
turnoff.Thesystemisnowreadyforuse.
GT Digital Display Entrance Station Addressing
Step 1:
Remove front cover from entrance station.
Step 2:
Toenterprogramming,useasmallscrewdrivertopushandreleasebuttonundertherubbercaponfrontof
speakermodule(GT-DA-L).TheamberLEDwillbeginashing,thenremainlit.Oncelit,theentrancestationisin
programmingmode.TheLCDwillshow“CONNECTING”whileinprogrammingmode.
Step 3:
AtGT-TLI,pressthePROGbutton.TheGT-TLIisnowconnectedtotheentrancepanel.
Step 4:
Scroll to the station number to be programmed or manually dial the number. When the tenant station number is
displayed,pushandreleasetheBell button
to assign the address to the GT-TLI station that is active. A blip tone
willbeplayed.
Step 5:
AtGT-TLI,pressthePROG button to complete programming.
Step 6:
Toexitprogramming,pushthebuttonundertherubbercapontheGT-DA-LmoduleagainandtheamberLEDwill
turnoff.Thesystemisnowreadyforuse.
DO NOT press and hold the Call Button as doing so will clear the memory for this button.
5
NAMES
DO NOT press and hold the Call Button as doing so will clear the memory for this button.
PowerLEDIndicator
Unitisonwhenlit.
POWER: Master power switch
(ON/OFF)
PROG:
Press to link GT-TLI to
system (in program mode)
3 Position Switch
OFF: Disables GT-TLI’s dial out function
ON: Enables GT-TLI’s dial out function
LOCAL PROG: Programming by using direct
connected telephone
6 | GT-TLI Installation / Operation Instructions
SET UP
Linking GT-TLI to GT system (continued)
TheGT-TLIcanbeprogrammedeitherwiththelocal(internal)telephoneorremotelybycallingin,viaDTMF.
(seeowchartbelow)
EnterPassword
⃰
2000# or
⃰
2001#
Enter programming
• telephone #
• time outs
• audio levels
• etc...
Enter00toexit
programming
GT-DM Entrance Station Addressing
Step 1: Whileinstandbymode,enter#plusIDcode(defaultis
⃰
1111).Re-enterIDcode.
Step 2: Usetheup/downarrowsandscrollto
PROGRAMMING
. Push the Bell button to enter programming mode.
TheamberLEDwillbeginashing,thenremainlit.Oncelit,theentrypanelisinprogrammingmode.TheLCDwill
show“CONNECTING”whileinprogrammingmode.
Step 3: AtGT-TLI,pressthePROGbutton.TheGT-TLIisnowconnectedtotheentrancepanel.
Step 4: Scroll to the station number to be programmed or manually dial the number. When the tenant station number is
displayed,pushandreleasetheBell button to assign the address to the GT-TLI station that is active. A blip tone
willbeplayed.
Step 5: AtGT-TLI,pressthePROG button to complete programming.
Step 6: Toexitprogramming,pressthe“X”buttononthepaneltoreturntothemainmenu(theamberLEDwillturnoff).
Scroll to
QUIT
andpressthe“X”buttonagain.Thesystemisnowreadyforuse.
DO NOT press and hold the Call Button as doing so will clear the memory for this entry.
Select“LOCALPROG”
on GT-TLI
Pick up local telephone
and dial code
Local Telephone
Dial phone #
of GT-TLI
Remote Telephone
SET UP - Accessing Program Mode
7
Note:
• A maximum of 10 seconds are allowed for each programming input. If the time exceeds 10 seconds,
the GT-TLI returns to standby mode.
• No programming entries are possible when the GT-TLI is playing indicator sounds.
• Entering a correct function code is indicated by 1 long beep.
• Correct entry of parameters are indicated by the message “The code entered is correct”
(see Programming Summary Chart).
• Incorrect entry of parameters are indicated by 2 long beeps, or by the automated message
“The code entered is incorrect”. The GT-TLI will wait for a new function number.
Remote programming via DTMF telephone
• DialthetelephonenumberoftheGT-TLI(tenant’sphonenumber).
• Anautomatedmessagewillplay“Callfromdoorpanel.”
• Dialoneofthetwofollowingprogramaccesscodes;
⃰
2000# or
⃰
2001#.
⃰
2000#=generalparameters(volumelevels,timing,etc.)
⃰
2001#=controlledparameters(callingtelephone#,etc.)
• Anautomatedmessagewillplay“Thecodeenterediscorrect.”
• Makeprogrammingchanges(seenextpage).
• Whenprogrammingiscomplete,dial00toexit.
• “Thecodeenterediscorrect”willbeplayedandtheGT-TLIwillgointoidlemode.
Local programming via telephone connected directly to GT-TLI
• Flipthe3positionswitchontheGT-TLItoLOCAL PROG.
• Activate handset on connected telephone.
• Dialoneofthetwofollowingprogramaccesscodes;
⃰
2000# or
⃰
2001#.
⃰
2000#=generalparameters(volumelevels,timing,etc.)
⃰
2001#=controlledparameters(callingtelephone#,etc.)
• Anautomatedmessagewillplay“Thecodeenterediscorrect.”
• Makeprogrammingchanges(seenextpage).
• Whenprogrammingiscomplete,dial00toexit.
• “Thecodeenterediscorrect”willbeplayedandtheGT-TLIwillgointoidlemode.
• Hanguphandsetandreturnthe3positionswitchtoONposition.
SET UP - Basic Programming
Thefollowing6programmingstepsmustbedonepriortooperatingtheGT-TLI.
Disabling / Enabling Door Calling Telephone
TheGT-TLIcanbedisabledfromcallingtheprogrammedtelephone,incaseswherethetenantwishesnottobe
disturbedbytheGTentrancepanel.ThedefaultsettingiswithDoorCallActivationenabled.
• Enter program access code
⃰
2001# -“Thecodeenterediscorrect”willbeplayed
• Enter
⃰
toenable,or# to disable
• “Thecodeenterediscorrect”willbeplayed,andtheGT-TLIwillgointoidlemode
Ring Duration of Locally Connected Telephone
Settheringdurationfortheconnectedtelephone(s).Timesetmustbebetween10-45seconds.
• Enter program access code
⃰
2001# -“Thecodeenterediscorrect”willbeplayed
• Enter 20-1longbeepwillbeplayed
• Enter nn-“Thecodeenterediscorrect”willbeplayed(nn=timeinseconds,i.e.30)
Program Remote Call Number
SettheremotetelephonenumberthatwillbedialedbytheGT-TLI.Thetelephonenumbercanbeupto16digitslong.
Ifthetelephonenumberislessthan16digits,press#afterthelastdigit.A"
⃰
“canbeusedwhenapauseisrequired.
Forexample,ifneedingtodialadigitpriortoaccessinganoutsidephoneline,orifdialingaphonenumberwithan
extension,usethe“
⃰
“forapause.
• Enter program access code
⃰
2001# -“Thecodeenterediscorrect”willbeplayed
• Enter 21-1longbeepwillbeplayed
• Enter nn #-“Thecodeenterediscorrect”willbeplayed(nn=telephonenumber)
To delete a telephone number.
• Enter program access code
⃰
2001# -“Thecodeenterediscorrect”willbeplayed
• Enter 21-1longbeepwillbeplayed
• Enter #-“Thecodeenterediscorrect”willbeplayed
Program DTMF Code for GT Entrance Panel
InorderforthetelephonetoactivatethedoorreleasecontactontheGTentrancepanel,a2-digitaccesscodemust
beenteredonthetelephonewhileincommunicationwiththedoorstation.Thedefaultcodeis10.
• Enter program access code
⃰
2000# -“Thecodeenterediscorrect”willbeplayed
• Enter 25-1longbeepwillbeplayed
• Enter nn-“Thecodeenterediscorrect”willbeplayed(nn=2digitaccesscode)
Program DTMF Code for GT-TLI Secondary Dry Contact
InorderforthetelephonetoactivatethesecondarydrycontactontheGT-TLI,a2-digitaccesscodemustbeentered
onthetelephonewhileincommunicationwiththedoorstation.Thedefaultcodeis20.
• Enter program access code
⃰
2000# -“Thecodeenterediscorrect”willbeplayed
• Enter 30-1longbeepwillbeplayed
• Enter nn-“Thecodeenterediscorrect”willbeplayed(nn=2digitaccesscode)
Program Duration of GT-TLI Secondary Dry Contact
ThesecondarydrycontactontheGT-TLIcanbeactivatedforadurationof1-10seconds.Thedefaultis5seconds.
• Enter program access code
⃰
2000# -“Thecodeenterediscorrect”willbeplayed
• Enter 32-1longbeepwillbeplayed
• Enter nn-“Thecodeenterediscorrect”willbeplayed(nn=timeinseconds,2digits)
When programming is complete dial 00 toexitprogrammingmode.
8 | GT-TLI Installation / Operation Instructions
SET UP - Advanced Programming
Ending Communication After Releasing Door on GT Entrance Panel
Choosetoendcommunicationimmediatelyafterdoorrelease(default),after5seconds,ornotatall.
• Enter program access code
⃰
2000#-“Thecodeenterediscorrect”willbeplayed
• Enter 35-1longbeepwillbeplayed
• Enter 1(immediatedisconnect),1longbeepwillbeplayed,enter0-“Thecodeenterediscorrect”willbeplayed
• Enter 1(5sec.delay),1longbeepwillbeplayed,enter1-“Thecodeenterediscorrect”willbeplayed
• Enter 0(nodisconnect)-“Thecodeenterediscorrect”willbeplayed
Ending Communication After Activating Secondary Contact on GT-TLI
Choosetoendcommunicationimmediatelyafterdoorrelease(default),after5seconds,ornotatall.
• Enter program access code
⃰
2000#-“Thecodeenterediscorrect”willbeplayed
• Enter 37-1longbeepwillbeplayed
• Enter 1(immediatedisconnect),1longbeepwillbeplayed,enter0-“Thecodeenterediscorrect”willbeplayed
• Enter 1(5sec.delay),1longbeepwillbeplayed,enter1-“Thecodeenterediscorrect”willbeplayed
• Enter 0(nodisconnect)-“Thecodeenterediscorrect”willbeplayed
DoorCallNoticationWhenLocallyConnectedTelephoneisinUse
Choosetoreceiveaverbalmessage(default)oratoneindicatingacallfromthedoorwhenthetelephoneisinuse.
• Enter program access code
⃰
2000#-“Thecodeenterediscorrect”willbeplayed
• Enter 43-1longbeepwillbeplayed
• Enter 1(verbalmessage),or0(beep)-“Thecodeenterediscorrect”willbeplayed
Ring Style Selection For GT Entrance Panel Calls
Choosebetween1.5secondsofringingfollowedby3.5secondsofsilencerepeated(default)or1secondofringfollowedby1
second of silence repeated.
• Enter program access code
⃰
2000# -“Thecodeenterediscorrect”willbe
played
• Enter 58-1longbeepwillbe
played
• Enter 0(1.5sec.on-3.5sec.off)or1(1sec.on-1sec.off)-“Thecodeenterediscorrect”willbe
played
Ring Duration Prior to GT-TLI Answering Outside Call
Enterthedurationinseconds(defaultis45sec.)thattheGT-TLIwillringbeforeansweringatelephonecall.Thisis
primarilyafactorwhenprogrammingfromanoutsideline.Timemustbesetinseconds,from10-255seconds.
• Enter program access code
⃰
2000#-“Thecodeenterediscorrect”willbeplayed
• Enter 59-1longbeepwillbeplayed
• Enter nnn(timeinseconds,3digit)-“Thecodeenterediscorrect”willbeplayed
Change Program Passwords
Changepasswordsforbothgeneralparameters(defaultis2000)andcontrolledparameters(defaultis2001).
Thepasswordsmustbe4digitsandmustbedifferentfromeachother.
• Enter program access code
⃰
2000# or
⃰
2001# -“Thecodeenterediscorrect”willbeplayed
• Enter 90(2000),orEnter91(2001)-1longbeepwillbeplayed
• Enter nnnn(nnnn=new4digitpassword)-“Thecodeenterediscorrect”willbeplayed
Language Selection for Voice Messages
Choosethelanguageforthevoicemessages(defaultisEnglish).
• Enter program access code
⃰
2000#-“Thecodeenterediscorrect”willbeplayed
• Enter 78-1longbeepwillbeplayed
• Enter n(n=language,0=French,1=English,2=Spanish)-“Thecodeenterediscorrect”willbeplayed
9
10 | GT-TLI Installation / Operation Instructions
SET UP - Advanced Programming (continued)
Communication Level For Local Telephone
AdjustthereceiveandtransmitcommunicationvolumefortheGTentrancepaneltothelocallyconnectedtelephone.
Receive from GT Entrance Panel. The default setting = 04.
• Enter program access code
⃰
2000# -“Thecodeenterediscorrect”willbeplayed
• Enter 06-1longbeepwillbeplayed
• Enter nn(nn=level,00maxlevel-31minlevel)-“Thecodeenterediscorrect”willbeplayed
Transmit to GT Entrance Panel. The default setting = 10.
• Enter program access code
⃰
2000#-“Thecodeenterediscorrect”willbeplayed
• Enter 07-1longbeepwillbeplayed
• Enter nn(nn=level,00maxlevel-31minlevel)-“Thecodeenterediscorrect”willbeplayed
Communication Level for Remote Dialed Telephone
AdjustthereceiveandtransmitcommunicationvolumefortheGTentrancepaneltotheremotedialedtelephone.
Receive from GT Entrance Panel. The default setting = 04.
• Enter program access code
⃰
2000#-“Thecodeenterediscorrect”willbeplayed
• Enter 08-1longbeepwillbeplayed
• Enter nn(nn=level,00maxlevel-31minlevel)-“Thecodeenterediscorrect”willbeplayed
Transmit to GT Entrance Panel. The default setting = 10.
• Enter program access code
⃰
2000# -“Thecodeenterediscorrect”willbeplayed
• Enter 09-1longbeepwillbeplayed
• Enter nn(nn=level,00maxlevel-31minlevel)-“Thecodeenterediscorrect”willbeplayed
Time Setting for Delay Call Transfer
Setthedelaytimewhendelaycalltransferisenabled.Calltransfercanbedelayedfrom1-40seconds.
The default setting = 10.
• Enter program access code
⃰
2000# -“Thecodeenterediscorrect”willbeplayed
• Enter 64-1longbeepwillbeplayed
• Enter nn(nn=timeinsec.,01-40)-“Thecodeenterediscorrect”willbeplayed
Switching to Communication Mode with Remote Telephone
Choosebetween3waysofswitchingtocommunicationwiththeremotetelephone.
0=switchifendofringingtoneisdetected
1=switchifDTMFdetected
2=switchimmediately(default)
• Enter program access code
⃰
2000#-“Thecodeenterediscorrect”willbeplayed
• Enter 95-1longbeepwillbeplayed
• Enter n(n=mode,0-1-2)-“Thecodeenterediscorrect”willbeplayed
11
SET UP - Advanced Programming (continued)
Default Values
Tones
ON signal ringing
OFF signal ringing
ON signal busy
OFF signal busy
ON signal EOC
OFF signal EOC
Value +/- Limits
1s +/- 200ms
3s +/- 200ms
200ms +/- 50ms
400ms +/- 50ms
500ms-200ms+50ms
500ms-200ms+50ms
Min & Max
800/1200
2800/3200
150/250
350/450
300/550
300/550
Values to Prog
080/120
280/320
015/025
035/045
030/055
030/055
Default Values
135/165
315/385
045/055
045/055
045/055
045/055
Disconnect After Silence or Continuous Signal
SetthetimethattheGT-TLIwillwaitbeforedisconnectingwheneithersilenceoracontinuoussignalisplayed.
Thetimecanbesetinincrementsof5seconds,upto45seconds.Enteravalue0through9.
0=functionoff,1=5sec,2=10sec,3=15sec,4=20sec,5=25sec,6=30sec,7=35sec,8=40sec,9=45sec
The defualt setting = 2.
• Enter program access code
⃰
2000# -“Thecodeenterediscorrect”willbeplayed
• Enter 97-1longbeepwillbeplayed
• Enter n(n=1-9)-“Thecodeenterediscorrect”willbeplayed
Automatic Pause Prior to Dialing
The GT-TLI can be set to pause from 1-6 seconds prior to dialing.
The defualt setting = 3 seconds.
• Enter program access code
⃰
2000# -“Thecodeenterediscorrect”willbeplayed
• Enter 98-1longbeepwillbeplayed
• Enter n(n=timeinseconds)-“Thecodeenterediscorrect”willbeplayed
Manually Programming Tones
Ring,Busy,andEndOfCommunication(EOC)tonesmayneedtobeadjustedmanuallywhenconnectingtheGT-TLItoa
PBX.RefertoPBXmanualforspecicsettingrequirements.Valueslistedaretypically3or4digits,inmilliseconds
(i.e.0.8secondswillbe800).
• Enter program access code
⃰
2000# -“Thecodeenterediscorrect”willbeplayed
• Enter 99-1longbeepwillbeplayed
• Enterthetonetypevalueoftheringingtone(1=simple,2=double)-1longbeepwillbeplayed
• EntertheminimumvalueoftheONsignaloftheringingtone(3-4digits)-1longbeepwillbeplayed
• EnterthemaximumvalueoftheONsignaloftheringingtone(3-4digits)-1longbeepwillbeplayed
• EntertheminimumvalueoftheOFFsignaloftheringingtone(3-4digits)-1longbeepwillbeplayed
• EnterthemaximumvalueoftheOFFsignaloftheringingtone(3-4digits)-1longbeepwillbeplayed
• Enterthetonetypevalueofthebusytone(1=simple,2=double)-1longbeepwillbeplayed
• EntertheminimumvalueoftheONsignalofthebusytone(3-4digits)-1longbeepwillbeplayed
• EnterthemaximumvalueoftheONsignalofthebusytone(3-4digits)-1longbeepwillbeplayed
• EntertheminimumvalueoftheOFFsignalofthebusytone(3-4digits)-1longbeepwillbeplayed
• EnterthemaximumvalueoftheOFFsignalofthebusytone(3-4digits)-1longbeepwillbeplayed
• EnterthetonetypevalueoftheEOCtone(1=simple,2=double)-1longbeepwillbeplayed
• EntertheminimumvalueoftheONsignaloftheEOCtone(3-4digits)-1longbeepwillbeplayed
• EnterthemaximumvalueoftheONsignaloftheEOCtone(3-4digits)-1longbeepwillbeplayed
• EntertheminimumvalueoftheOFFsignaloftheEOCtone(3-4digits)-1longbeepwillbeplayed
• EnterthemaximumvalueoftheOFFsignaloftheEOCtone(3-4digits)-1longbeepwillbeplayed
IMPORTANT:
IfthereisnoEOCtone,oriftheEOCiscontinuous(noOFFsignal),enter000forthe4valuesofthistone.
12 | GT-TLI Installation / Operation Instructions
SET UP - Advanced Programming (continued)
Audible Level of Voice Messages
AdjustthevolumelevelofaudiblemessagesplayedattheGTentrancepanel.
• Enter program access code
⃰
2000#-“Thecodeenterediscorrect”willbeplayed
• Enter 18 -1longbeepwillbeplayed
• Enter n(n=level,0maxlevel-7minlevel)-“Thecodeenterediscorrect”willbeplayed
VoiceMessages
Message#1: “Pleasewait,yourcallisinprogress.”
Message#2: “Pleaseenter.”
Message#3: “Sorry,thelinebusy.Pleasetryagainlater.”
Message#4: “Sorry,noanswer.Pleasetryagainlater.”
Message#5: “Thecodeenteredisincorrect.”
Message#6: “Thecodeenterediscorrect.”
Message#7: “Callfromdoorpanel.”
Message#8: “Telephonecall.”
Message#9: “Routingon.”
Message#10: “Routingoff.”
Message#11: “Yourcallisinprogress.”
Enable / Disable Message #2
IftheguidancelanguagefeatureisturnedonattheGTentrancepanel,itisrecommendedthatMessage#2be
turned off to avoid confusion.
• Enter program access code
⃰
2000#-“Thecodeenterediscorrect”willbeplayed
• Enter 41-1longbeepwillbeplayed
• Enter nn(nn=02,message2)-1longbeepwillbeplayed
• Enter 1(enablemessage),or0(disablemessage)-“Thecodeenterediscorrect”willbeplayed
Restore Default Parameters
To restore the GT-TLI to default parameters.
• Enter program access code
⃰
2000#-“Thecodeenterediscorrect”willbeplayed
• Enter 29-“Thecodeenterediscorrect”willbeplayed
13
SET UP - Quick Reference Programming Chart
Password Code Function Parameters DefaultValue
⃰
2000# 18 Audiolevelforvoicemessage Max0,Min7 4
25 DTMFcodeforGTpanelrelay 2digits 10
29 Restoredefaultparameters Factorydefault -
30 DTMFcodeforGT-TLIdrycontact 2digits 20
32 DurationofGT-TLIdrycontact 01-10(1-10seconds) 05
35 Endcommunicationwhenactivating 0=communicationcontinues 1-0
dry contact on GT panel 1-0 = communication ends after
contact is activated
1-1=communicationends5sec.
after contact is activated
37 Endcommunicationwhenactivating 0=communicationcontinues 1-0
dry contact on GT-TLI 1-0 = communication ends after
contact is activated
1-1=communicationends5sec.
after contact is activated
41 Enable / Disable message 2 0 = message off 1
1 = message on
43 Callnoticationwhentelephone  0=tone 1
is in use 1 = verbal message
58 RingstylewhenGTpanelcalls 0=1.5secon,3.5secoff 0
1=1secon,1secoff
59 RingdurationpriortoGT-TLIanswering 001-255(1-255seconds) 045
outside call
64 Timesettingfordelaycalltransfer 01-40(1-40seconds) 10
78 Languageselectionforvoicemessages 0=French,1=English,2=Spanish 1
90 Createnewpassword 4digits 2000
95 SwitchtoCommunicationmodewith 0=tonedetection 0
remotetelephone 1=DTMFdetection
97 Disconnectaftersilenceorcont.tone 1digit,0-9(5secintervals) 2(10sec)
98 Automaticpausepriortodialing 1-6seconds 3
99 Programmingtonesmanually -
⃰
2001#
⃰
Enabling door calling telephone Enable
⃰
# Disable door calling telephone Disable #
20 Ringdurationoflocallyconnected 10-45seconds -
telephone
21 Programremotecall# Max.16numbers -
91 Createnewpassword 4digits 2001
00 Codetoexitprogrammingmode - 00
14 | GT-TLI Installation / Operation Instructions
Locally Connected Telephone (i.e. cordless or corded telephone in apartment)
Receiving a call from the door:
• Telephone rings
• “Callfromdoorpanel”messageisplayed
• Communication can begin after message is played
• Toreleasedoor(buzz-in),enter2digitcode(defaultis10)
• Systemwilldisconnectafter1minute
Receivingacallfromdoorwhilecurrentlyonphone:
• “Callfromdoorpanel”messageisplayed
Option1:Donothing,doorstationwilltimeout
Option2:Hangupcurrentcall,phonewillring,andcommunicationwithvisitoratdoorcanbegin
Option 3: Press #keytoendcurrentcallandbegincommunicationwithvisitoratdoor
• Toreleasedoor(buzz-in),enter2digitcode(defaultis10)
• Systemwilldisconnectafter1minute
Receivingatelephonecallwhilecommunicatingwithvisitoratdoor:
• “TelephoneCall”messageisplayed
• Press #keytoswitchtotelephonecall,whichwillterminatecommunicationtotheGTpanel
Remote Telephone Instructions: (i.e. answering door with a cell phone)
Receiving a call from the door:
• Telephone rings
• Answercall
• Communicationwithdoorisimmediate
• Toreleasedoorenter2digitcode(defaultis10)
• Systemwilldisconnectafter1minute
Forwarding Door Calls to a Remote Telephone (i.e. cell phone)
Locally connected telephone:
• Press #
⃰
1tobeginforwardingdoorcallstoaremotetelephone-“Thecodeenterediscorrect”willbeplayed
• Press #
⃰
0tostopforwardingdoorcallstoaremotetelephone-“Thecodeenterediscorrect”willbeplayed
Forwarding Door Calls to a Locally Connected Telephone (tenant)
Remote telephone:
• DialGT-TLItelephonenumber(tenant’sphonenumber)
• GT-TLIanswerswith“Thecodeenterediscorrect”afterringdurationisreached
• Press #
⃰
1tobeginforwardingdoorcallstoaremotetelephone-“Thecodeenterediscorrect”willbeplayed
• Press #
⃰
0tostopforwardingdoorcallstoaremotetelephone-“Thecodeenterediscorrect”willbeplayed
Disable / Silence Door Call-ins
From a locally connected telephone:
• Press #
⃰
#todeactivateGTpanelcallin-“Thecodeenterediscorrect”willbeplayed
From a remote telephone:
• DialGT-TLItelephonenumber(tenant’sphonenumber)
• GT-TLIanswerswith“Thecodeenterediscorrect”afterringdurationisreached
• Press #
⃰
#todeactivateGTpanelcallin-“Thecodeenterediscorrect”willbeplayed
Enable / Activate Door Call-ins
From a locally connected telephone:
• Press #
⃰
⃰
toactivateGTpanelcallin-“Thecodeenterediscorrect”willbeplayed
From a remote telephone
• DialGT-TLItelephonenumber(tenant’sphonenumber)
• GT-TLIanswerswith“Thecodeenterediscorrect”afterringdurationisreached
• Press #
⃰
⃰
toactivateGTpanelcallin-“Thecodeenterediscorrect”willbeplayed
OPERATION
15
15
OPERATION - Mode Selection
Mode OFF
Whenthe3positionswitch(LOCALPROG/ON/OFF)isinOFFposition,GTpanelcallwillnotringthelocallyconnected
telephone or the remote telephone.
Mode ON Without Transfer
Whenthe3positionswitch(LOCALPROG/ON/OFF)isinONpositionandthetransferfeatureisnotturnedon,
theGTpanelcallwillringthelocallyconnectedtelephone.
Mode ON With Transfer
Whenthe3positionswitch(LOCALPROG/ON/OFF)isinONpositionandthetransferfeatureturnedon,
theGTpanelcallwillringtheremotetelephone.
Local
Remote
Local
Remote
Local
Remote
PARAMETERS OF INSTALLATION
Programming DefaultValue Installation
Ringdurationoftheinternaltelephoneset 45seconds ___________________________
Remotecalltelephonenumber 460 ___________________________
DTMFcodeforoperating  10 ___________________________
GTPanel’sdrycontact
DTMFcodeforoperatingGT-TLI’s 20 ___________________________
secondary dry contact
OperatingtimeofGT-TLI’s 5seconds ___________________________
secondary dry contact
Endingcommunicationafterreleasing Yes ___________________________
door on GT entrance panel
Endingcommunicationafteractivating Yes ___________________________
secondary contact on GT-TLI
Generalparameterspassword 2000 ___________________________
Controlledparameterspassword 2001 ___________________________
PhonenumberofGT-TLI - ___________________________
S/NofGT-TLI - ___________________________
16 | GT-TLI Installation / Operation Instructions
17
BASIC PROGRAMMING STEP FROM REMOTE TELEPHONE
DialthephoneoftheGT-TLI:_____________,callfromdoorpanelwillbeplayed
Entering Remote Call Number
Enter
⃰
2001#-“Thecodeenterediscorrect”willbeplayed
Enter 21,1longbeepwillbeplayed
Entertelephonenumber____________,“Thecodeenterediscorrect”willbeplayed
Enter 00toexit-3shortbeepswillbeplayed
Adjust Ring Duration of Local Telephone
Enter
⃰
2001#-“Thecodeenterediscorrect”willbeplayed
Enter 20,1longbeepwillbeplayed
Enterdurationinseconds(10-45s)____________,“Thecodeenterediscorrect”willbeplayed
Enter 00toexit-3shortbeepswillbeplayed
Enter Door Release Code for GT Entrance Panel
Enter
⃰
2000#-“Thecodeenterediscorrect”willbeplayed
Enter 25,1longbeepwillbeplayed
Enter2digitcode____________,“Thecodeenterediscorrect”willbeplayed
Enter 00toexit-3shortbeepswillbeplayed
Enter Door Release Code for Secondary Contact on GT-TLI
Enter
⃰
2000#-“Thecodeenterediscorrect”willbeplayed
Enter 30,1longbeepwillbeplayed
Enter2digitcode____________,“Thecodeenterediscorrect”willbeplayed
Enter 00toexit-3shortbeepswillbeplayed
Adjust Contact Duration of Secondary Contact on GT-TLI
Enter
⃰
2000#-“Thecodeenterediscorrect”willbeplayed
Enter 32,1longbeepwillbeplayed
Entertimeinseconds(1-10s,2digits)____________,“Thecodeenterediscorrect”willbeplayed
Enter 00toexit-3shortbeepswillbeplayed
18 | GT-TLI Installation / Operation Instructions
SPECIFICATIONS
Dimensions 9-7/16”x7-1/16”x2-1/16”,240mmx180mmx53mm
Weight 6.35oz,0.18kg
Temperature 32°F-140°F,0°C-40°C
Connections StandardsinglelinePBXjackmastersocketwithin50metersor
PABXextensionoftheinternaltelecommunicationnetworkofacompany.
Powerrequired 12V-24VAC/DC-0.5A
Consumption 12VAC/DC 24VAC/DC
Standby:95mA Standby:45mA
Standards EN60950
EN55022Edition98ClassB
EN55024Edition98ClassB
FCCparts68&15
IC CS-03
Programming Localorremotelyviatouch-tone(DTMF)telephone
SystemCapacity 1callnumber(16digits)
Memory Non-volatilememory
Chassis ABS plastic
Symptom Recommendations
TheredLEDontheGT-TLIdoesn’tlight. Checkpolarityonpowersupply.
Verifyvoltageisadequate.(12V-24VAC/DC-0.5A).
GT-TLI does not ring the programmed Check connection of telephone line on the CO terminal.
telephone number. Re-program the call number.
Inopportuneswitchingwhileincommunication GT-TLIisinstalledonaninternallineofaPABX.Tonesaredifferent,
whenexternalnumberiscalled. refertoAdvancedProgrammingsectiononprogrammingtonesmanually.
GT-TLIisconnectedtoaPBXtelephoneline.Tonesaredifferent,
refer to Advanced Programming section on programming tones manually.
TROUBLESHOOTING TIPS
WARRANTY
Aiphonewarrantsitsproductstobefreefromdefectsofmaterialandworkmanshipundernormal
useandserviceforaperiodoftwoyearsafterdeliverytotheultimateuser.Aiphonewillrepairfree
ofchargeorreplaceatnochargeshouldtheproductbecomedefectiveuponwhichexamination
shalldisclosetobedefectiveandunderwarranty.Aiphonereservesuntoitselfthesolerighttomake
thenaldecisionwhetherthereisadefectinmaterialsand/orworkmanship;andwhetherornotthe
productiswithinthewarranty.ThiswarrantyshallnotapplytoanyAiphoneproductwhichhasbeen
subjecttomisuse,neglect,accident,ortouseinviolationofinstructionsfurnished,norextended
tounitswhichhavebeenrepairedoralteredoutsideofthefactory.Thiswarrantydoesnotcover
batteriesordamagecausedbybatteriesusedinconnectionwiththeunit.Thiswarrantycoversbench
repairsonlyandanyrepairsmustbemadeattheshoporplacedesignatedinwritingbyAiphone.
Aiphonewillnotberesponsibleforanycostsincurredinvolvingon-siteservicecalls.
ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,
pursuanttoPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotection
againstharmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,uses,andcan
radiateradiofrequencyenergy,andifnotinstalledandusedinaccordancewiththeinstructions,may
causeharmfulinterferencetoradiocommunications.However,thereisnoguaranteethatinterference
willnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradio
ortelevisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,theuseris
encouragedtotrytocorrecttheinterferencebyoneofmoreofthefollowingmeasures:
• Reorient or relocate the receiving antenna
• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.
• Increasetheseparationbetweentheequipmentandreceiver.
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
ThisequipmentcomplieswithPart68oftheFCCrulesandtherequirementsadoptedbytheACTA.
OnthebackofthisequipmentisalabelthatcontainstheproductidentierUS:23BOT05B578 along
withtheREN(RingerEquivalencyNumber)of0.5B. Ifrequested,thesenumbersmustbeprovidedto
the telephone company.
Aplugandjackusedtoconnectthisequipmenttothepremiseswiringandtelephonenetworkmust
complywiththeapplicableFCCPart68rulesandrequirementsadoptedbytheACTA.Acompliant
telephonecordandmodularplugisprovidedwiththisproduct.Seeinstallationinstructionsfordetails.
Ifthisequipment(GT-TLI)causesharmtothetelephonenetwork,youwillbenotiedbythe
telephonecompanyinadvance.Adiscontinuationofservicemayberequired.Ifnecessary,youwill
beadvisedofyourrightstoleacomplaintwiththeFCC.
Thetelephonecompanymaymakechangesinitsfacilities,equipment,operations,orprocedures
thatcouldaffecttheoperationofthisequipment.Ifthishappensthetelephonecompanywillprovide
advancenoticeinorderforyoutomakenecessarymodicationstomaintainuninterruptedservice.
IftroubleisexperiencedwiththeGT-TLI,pleasecontactAiphoneCorporationat800-692-0200for
repairinformation.Iftheequipmentiscausingharmtothetelephonenetwork,thetelephonecompany
mayrequestthatyoudisconnecttheequipmentuntiltheproblemisresolved.
19
FCC REQUIREMENTS
Aiphone Corporation
1700130thAve.NEBellevue,WA98005
Ph:(800)692-0200Fax:(425)455-0071
www.aiphone.com[email protected]
/