PMX402M

Pyle PMX402M User manual

  • Hello! I am an AI chatbot trained to assist you with the Pyle PMX402M User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Pyle'PMX'SeriesMultiChannelMixers
www.PyleAudio.com
Warnings
x Pleasebesuretoread,keepandrefertoinstructionslistedinthismanual.
x Donotusethisdevicenearwaterorexposetomoisture.
x Cleanonlywithadrycloth.
x Donotblockanyventilationopeningsandallowadequatespaceforairflowduringoperation.
x
Donotinstallnearanyheatsourcesorotherdevicesthatproduceheat.
x Donotdefeatthesafetypurposeofthepolarizedorgroundingtypeplug.
x Protectthepowercordfromanykindofdamageorcorrosion.
x Unplugthemixerwhennotinuseorwhenunused
forlongperiodsoftime.
x Referallservicetoqualifiedservicepersonnel.Servicingisrequiredwhenthemixerhasbeendamagedorperformsinanunusually.
x Useonlyspeakercableswhenconnectingspeakerstoamplifieroutputs.Usingothertypesofcablesisafirehazard.
x Exposuretoextremely
highnoiselevelsmaycauseinpermanenthearingloss.Individualsvaryconsiderablytonoiseinducedhearinglossbut
takeprecautionwhenlisteningathighlevels.
x Ifthepowercordisdamaged(i.e.,cutorabarewireisexposed),askyourdealerforareplacement.Usingtheunitwith
adamagedpowercord
isafireandelectricalshockhazard.
x Shouldthisunitbedroppedorthecabinetbedamaged,turnthepowerswitchoff,removethepowerplugfromtheACoutlet,andcontactyour
dealer.Ifyoucontinueusingtheunitwithoutheedingthisinstruction,fireorelectricalshockmayresult.
CAUTION
Iftheunitisdamagedornonoperational,pleasenotifyyourdealerandtheshippingcompanyimmediately.Claimsfor
damageorreplacementmaynotbegrantedifnotreportedproperlyorinatimelymanner.
x Connectthisunit’spowercordonlytoanACoutletofthetypestatedinthisManualorasmarkedontheunit.Failuretodosomayresultin
fireand/orelectricalshock.
x Donotplaceheavyobjectsontopofthepowercord.Adamagedpowercordisalsoafireandelectricalshockhazard.
x Useonlytheincludedpowercordforthisunit,usingothertypesmayagainresultinfireandelectricalshock.
x Donotsetallequalizercontrolsandfaderstomaximumlevels.Doingsomaycauseoscillationdependingonthecondition
oftheconnected
unitandspeakers,andmayalsodamagethespeakers.
x Theperformanceofcomponentsonthismixersuchasswitches,rotarycontrols,faders,andconnectors,deterioratesovertime.Therate
dependsontheoperatingenvironmentandissometimesunavoidable.Consultyourdealeraboutreplacingdefectivecomponents.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DONOTATTEMPTTOOPENORACCESSTHEINSIDEOF
THEUNIT.REFERALLSERVICINGTOAQUALIFIEDPYLE
SERVICEPERSONNEL.
This lightning flash symbol is intended to alert the user to the presence of uninsulated and “dangerous
voltage”withinthemixer'senclosurethatmaybeofsufficientpowertoconstituteariskofelectricshock.
Thisexclamationpointsymbolisintendedtoalerttheusertothepresenceofimportantoperating
andmaintaininginstructions,thatoneshouldpayattentiontoandkeepforfuturereference.
Pyle'PMX'SeriesMultiChannelMixers
www.PyleAudio.com
Installation
Installthemixeronanevensurfacetoallowforsufficientairflowandventilationduringuse.Thedeviceisequippedwith
electronicallycontrolledcoolingfanstoprotectagainstthermaloverloadandinternalcircuitryfromdamagedueto
extremeheat.Pleaseavoidcoveringanysidesoftheunitorplacingobjectsorotheraudiodevicestooclosetoyourmixer.
Priortoconnectingandpoweringontheunit,makesurethatthedevicematchesthevoltageandfrequencyofyour
powersupply.Poweroffthemixerwhennotinuse.
CablesandConnections

RCA 1/4''TRSandMono XLR3Pin
RCA connector jacks have been most
commonly used in home audio systems
and configurations for years. Also known
as RCA 'phono', 'plugs' or 'audio
connectors' , these jacks are always
unbalanced, and generally carry a line
level signal at –10 dB, nominal signal
levels. The RCA connector jacks are most
likely
used when connecting an audio
devicelikeamediaplayerorotherhome
audio type source to your mixer. These
connector jacks are also used when
connectingtotheoutputofyourdevices.
1/4''monoandstereoconnectorjacksare
labeled for use as unbalanced mono,
unbalanced stereo, balanced mono,
or as
an insert patch point. A 1/4'' TRS (Tip,
Ring, Sleeve), 3conductor connection, or
'Stereo' cable allows a single connection
signal to carry 2channels of audio; also
can be used for mono balanced signals.
While,a1/4''TS(Tip,Sleeve),2conductor,
or'Mono'cablearemost
popularlyknown
for their use in guitar or linelevel
instrument connection; they can also be
usedformonounbalancedsignals.
XLRconnectorjacks,almostalwayscarries
a balanced signal. Depending on your
device,theseconnectorjacksmayalsobe
capable of handling unbalanced signals.
Microphones generally have this type
of
connector, as well as most other
professionalaudioequipmentanddevices.
Typical3PinXLRsocketsarefixedwiththe
rightmostpinbeingthe'ground',theleft
most pin being 'hot' and the bottom pin
asthe'neutral'.
TechnicalSpecifications
MonoInputs
MicrophoneInputs(XENYXMicPreamp)
XLR,electronicallybalanced,discreteinputcircuit
MicE.I.N.(20Hz20kHz)
@0OhmSourceResistance
@50OhmSourceResistance
@150OhmSourceResistance
134dB/135.7dBAWeighted
131dB/133.3dBAWeighted
129dB/130.7dBAWeighted
FrequencyResponse
<10Hz150kHz(1dB)
<10Hz200kHz(3dB)
GainRange +10dBto+60dB
MaximumInputLevel +12dB@+10dBGain
Impedance Approximately2.6kOhm,Balanced
SignaltoNoise 110dB/112dBAWeighted
Distortion(THD+N) 0.005%/0.004%,AWeighted
LineInput 1/4''TRSConnectors,ElectronicallyBalanced
ChannelEqualization
(FrequencyHz)
ControlRangeHigh:@10k+/15dB
ControlRangeLow:@60k+/15dB
Master5BandGraphicEQ
Frequency:Hz(60,250,1K,4K,12K)
ControlRanges:+/12dB
Pyle'PMX'SeriesMultiChannelMixers
www.PyleAudio.com
ConnectorSpecifications
EffectsConnectors
EffectsSendEffectsReturn
1/4''TSConnector,Unbalanced
Impedance:Approx.1kOhm
OutputLevel:10dB
ControlRoomOutputs
RCAUnbalanced
Impedance:Approx.1kOhm
OutputLevel:10dB
HeadphoneOutput
1/4''TRSConnector,Stereo
OutputLevel:+19dB/150Ohm(+25dB)
MixerLayoutandControlsFrontPanel
1.
3PINLOWIMPEDANCEMICINPUT
Electronically balanced XLR input is designed to accept signals from any
balancedor unbalanced low impedance (Low Z)microphone. (Pin 1 to the
shield,Pin2tothe'hot'(positivepolarity)sideoftheaudiosignal,andPin3
tothe'cold'sideofthesignal.Dynamicorribbontypemicrophones
donot
require phantom power. Microphone inputs are generally more sensitive
thantheLineinputs.
2.
1/4''LINEINPUT
Line/High impedance input, 1/4” connector jack is designed to accept
balanced or unbalanced linelevel signals such as those from keyboards,
drum machines, or samplers. There is enough gain available on the line
inputtoacceptevenlowerlevelsignals,suchasthosefromanunbalanced
microphoneorguitaroutput.Ifabalancedsignalistobeconnectedtothe
line input, then a1/4” TRS (stereo) phone plug shouldbe wiredfor: Tip =
positive(+),Ring=negative(),Sleeve=ground.
*Pleasenote, the diagram above doesnot reflect all Pyle'PMX' Series models. Somefeatures listed are model specific,and are just madefor descriptive
purposesforamorethoroughunderstandingofthePMXSeriesMixers.Toviewmodelspecificinformation,pleasevisitwww.PyleAudio.comandbrowsefor
thespecificmodelnumber.(PMXMixerSeriesModels:PMX401,PMX402M,PMX602M,PMX630I,PMX640BT,PMX802M,PMX830I,PMX840BT)
Pyle'PMX'SeriesMultiChannelMixers
www.PyleAudio.com
3.
GAINCONTROL
Adjustthevolumefortheselectedchannel'ssignal.It sendthesignaltothe
mastermixbuss,pleaserememberthisfunctionallowstheunittoactasa
preamp (...so if you are using a device that has its own unique volume
control, you will need to perform some volume adjustment and level
matching.Optimalsoundperformanceisachievedwhenaudiodistortionis
ataminimum.
4.
EQCONTROLINDEPEDANTCHANNEL
Independent channel selection allows equalization effect controls for the
input signal. This gives you the ability to adjust the overall tone of the
selectedinput. Itacts as acut orboostcontrol, that addsto or diminishes
thesoundquality60Hz10kHz(+/15dB).
5.
EFFECTCONTROLINDEPEDANTCHANNEL
Also known asEFFX controls, thisis a 'send' control to the reverb buss. It
controls the amount of reverberation added to the selected destination
channelinputsignal.
6.
LCDDISPLAYUSB/SDCONTROL
Use the digital LCD control panel and touch button to control your
connected flash memory drive. Take music from your computer's media
library,transferittoyourremovablememorystoragedeviceandletitplay
throughthemixer.SupportsMP3andWMAmusicformats.
7.
EFFECTSCONTROLLERS
TakecontroloftheEffectsVolume,EffectsEchoandEffectsDelay.Control
theoverallsignalleveloftheeffects'mix'thatisreceived.DelayandEcho
controlsallowyoutovariablyadjusttheeffectintervaltime.Setthiscontrol
lower for shorter Echo times to emulate similar 'doubling' effects while
setting a higher level provides longer effect times for 'stadiumlike' delay
sound.
8.
USB/SDVOLUMECONTROL
AdjustthevolumeforconnectedmediastreamingviaUSBFlashMemoryor
SDMemoryCards
9.
MASTERVOLUMECONTROL
Adjust the volume for the entire mixer and connected devices playing
throughthemixer.
10.
MASTERGRAPHICEQUALIZERCONTROL
(LowLow/MidMidMid/HighHigh),thesemasterEQcontrolsallowyou
to adjust the levels of signal frequencies. 5Band frequency. graphic EQ
faders put you in control and allow you to achieve optimal sound
performance. Adjust the faders accordingly with different acoustic and
environmentalconditions.
11.
POWERLED
ThisLEDwillilluminatewhentheunitisswitchedon.
12.
AUX(3.5mm)INPUT
Auxiliary input connector jack for connecting devices like MP3 Players,
Smartphones,Tablets,etc.
13.
CD/TAPE:INPUT
Use the RCA (L/R)input connector jacksto connect a stereo signaloutput
devicetothemixer.(CD,Tape,Cassette,MP3,Smartphone,Tablet,Mac,PC,
Laptop,etc.)
14.
REC:OUTPUT
ThissignalRCA(L/R)outputconnectorjacksareforconnectinganexternal
device to record from the mixer.Both channelsare conformedinto mono
forcompatibility.Thesignalsarethentaken'premaster'meaningthesignal
is without reverb or the master tone section does not include the tape
signal.The connectedsignal becomesthe 'main'bus signalbefore passing
through the mixer's 'master' level controls and graphic equalizer.
(Impedance:1kOhm@10dB)
15.
INPUTVOLUMECONTROL
This control adjusts the level of the input signal applied to the CD/TAPE
Input.
Pyle'PMX'SeriesMultiChannelMixers
www.PyleAudio.com
MixerLayoutandControlsBackPanel
16.
ACPOWER
ThepowersupplycableisthestandardvoltageforUSACwall
outlets.Itisgroundedandshouldneverhavethegroundpin
removedforanyreason.
17.
SPEAKEROUTPUTS
1/4''speakeroutputs(A/B).Standard2conductorphonejacks
arewiredinparallel,witheachhavingtheabilitytoconnectto
yourspeakersystem.
18.
EFFECTLOOP
Return:
Monounbalanced1/4''connectorjackforincorporatingreturn
effectorotherlinelevelsource.Itbringstheoutputofthe
externaleffectsdevicebackintothemixerforfurtherprocessing.
(Impedance:10KOhms@10dB).
Send:
Monounbalanced1/4''2Conductorlineoutputs.Usedto
connectadditionalrecordingdeviceorexternaleffectsprocessor.
Appliestotheinputofanexternaleffectsunitandallowsyouto
'send'yourdedicatedsignalouttotheconnectedexternal
device.(Impedance:1kOhm@10dB).
19.
POWERSWITCH
ControlthepoweroftheunitON/OFF.Whentheunitispowered
on,theLEDindicatorlightonthefrontwillshineblue.
Balancedvs.Unbalanced
Balancedlines are made specifically for reducingaudiointerference and noise rejection. The rule ofthumb says, the longer thecable,the
morenoiseyouraudiosignalislikelytoencounter.Youraudiocableactsasanantennaandhastheabilitytopickupneighboringfrequencies,
andotherenvironmentalfactors,thatmayinterferewiththewayyoursoundperforms.The'noise'thatcanaffectyouraudiosignalsinclude
electromagnetic sound waves that are generated by devices like neighboring sound processors, computers, fans, motors, etc. Therefore,
balancedlinesarethebestoptionforrunninglongcablethroughyouraudioequipment.However,if
youraudioequipmentisconfinedwithin
a single room or small space, then unbalanced lines will function sufficiently; keep in mind, the less interfering electromagnetic wave
producing devices aroundyour equipment, the better. Balanced connector lines arealso widely used with microphone connection. The
outputsignalfrommostmicrophonesisrathersmall,soeventhesmallestamountofinterfering'noise'willbeevidenttoyourears.
Pyle'PMX'SeriesMultiChannelMixers
www.PyleAudio.com
Models:PMX630iandPMX830iwithBuiltin30PiniPodDocks
Models:PMX640BTandPMX840BTwithBuiltinBluetoothWirelessMusicStreaming
All'PMX'Mixerscomewithincludedpowercable:
AudioConnectionsandAdditionalNotes:
Weshouldliketodrawyourattentiontothefactthatextremevolumesmaydamageyourhearingand/oryour
headphones or loudspeakers. TurntheMAINMIXcontrolandphones control inthemainsectionfully down
beforeyouswitchontheunit.Alwaysbecarefulto
setappropriatevolumelevels.
Please,preferably,usecommercialqualityRCAcablestowiretheinputsandoutputs.Youcan,ofcourse,also
connect unbalanced devices tothebalancedinput/outputs. Use either mono plugs, or ensure thatringand
sleevearebridgedinsidethestereoplug(orpins1&3inthecaseofXLRconnectors).
You will need a larger number of cables for the various connections to and from the mixer console. Please
operatewithcare,followinstructionsanduseonlyhighgradeconnectioncablesduringanyandalloperation.
Pleaseuseonlythepowersupplyunitprovidedwiththeconsole.
Pyle'PMX'SeriesMultiChannelMixers
www.PyleAudio.com
'PMX'MixerSeriesModels&Specifications:
PMX630i
x 6-Channel System Power Mixer
x (6) Balanced 3-Pin Microphone Inputs
x (6) 1/4'' High Impedance Inputs
x Built-in 30-Pin iPod Dock
x Aux (3.5mm) Input Connector Jack
x Connect iPod, MP3 Players, iPhone, Smartphones, Tablets, etc.
x Master System EFFX, EQ & Volume Controls
x 5-Band Graphic Equalizer
x Effects Control & Send
x USB Flash & SD Memory Card Readers
x File Compatibility: MP3 & WMA Formats
x LCD Digital Display Screen with Touch Button Controls
x Independent Channel EQ, Treble, Bass, Reverb Controls
x 1/4'' Send/Return Jacks & (2) Conductor } Speaker Outputs
x RCA (L/R) Record Connector Jacks
x Convenient Carry Handle
x Built-in Cooling Fan
Technical Specs:
x Maximum Power Output: 600 Watts 4-Ohms
x Frequency Response: <10Hz - 150Hz (-1dB)
x Max. Input Level +12dBu @ +10dB Gain
x S/N Ratio: 110dB / 112dB A-Weighted
x Channel Tone Adjust (+/-15dB)
x Gain Range: +10 to +60dB
x Master EQ Control Ranges: +/- 12dB
x Distortion (THD+ N): 0.005% / 0.004%
x Power: 110/220 Voltage Switchable
x Dimension: 17.91'' x 12.79'' x 9.64''
PMX830i
x 8-Channel System Power Mixer
x (8) Balanced 3-Pin Microphone Inputs
x (8) 1/4'' High Impedance Inputs
x Built-in 30-Pin iPod Dock
x Aux (3.5mm) Input Connector Jack
x Connect iPod, MP3 Players, iPhone, Smartphones, Tablets, etc.
x Master System EFFX, EQ & Volume Controls
x 5-Band Graphic Equalizer
x Effects Control & Send
x USB Flash & SD Memory Card Readers
x File Compatibility: MP3 & WMA Formats
x LCD Digital Display Screen with Touch Button Controls
x Independent Channel EQ, Treble, Bass, Reverb Controls
x 1/4'' Send/Return Jacks & (2) Conductor } Speaker Outputs
x RCA (L/R) Record Connector Jacks
x Convenient Carry Handle
x Built-in Cooling Fan
Technical Specs:
x Maximum Power Output: 600 Watts 4-Ohms
x Frequency Response: <10Hz - 150Hz (-1dB)
x Max. Input Level +12dBu @ +10dB Gain
x S/N Ratio: 110dB / 112dB A-Weighted
x Channel Tone Adjust (+/-15dB)
x Gain Range: +10 to +60dB
x Master EQ Control Ranges: +/- 12dB
x Distortion (THD+ N): 0.005% / 0.004%
x Power: 110/220 Voltage Switchable
x Dimension: 20.67'' x 12.80'' x 9.64''
PMX640BT
x Bluetooth Wireless Music Streaming
x Works with Virtually Any Bluetooth Enabled Device
x (iPhone, Android, Smartphone, iPad, Tablet, PC, etc.)
x Digital LCD Display & Front Facing Control Center
x USB Flash Drive & SD Memory Card Readers
x 3-Pin Low Impedance Balanced Microphone Inputs
x 1/4'' Line/ High Impedance Balanced Inputs
x Independent Channel Volume, EQ & EFFX Controls
x Master 5 Band Graphic Equalizer
x EQ & Master EFFX Control of Level, Echo & Reverb Controls
x Aux (3.5mm) Input Jack for Connecting External Devices
x Headphone Output: 1/4'' TRS Stereo Connector
x RCA & 1/4'' Effects Loop Connectors
x Additional RCA Inputs: Tape Play (L/R), Tape Record (L/R)
Technical Specs:
x 600 Watt Output Power
x 8 Ohm Impedance Each Channel
x Line Level Impedance 10K Ohms @ -10dBv
x Mono Microphone Inputs (XENYX Mic Pre-Amp)
x XLR: Electronically Balanced Discrete Input Circuit
x Frequency Response: <10Hz150kHz (-1dB), <10Hz200kHz (-
3dB)
x Gain Range: +10 - +60dB
x Max. Input Level: +12dBu @ +10dB Gain
x Impedance: Approx. 2.6k Balanced
x Signal-to-Noise Ratio: 110dB / 112dBA Weighted
x Distortion: (THD+N): 0.005% / 0.004% A- Weighted
x Channel Equalization: Control Range
x High @ 10K +/-15dB, Low @ 60K +/-15dB
x Master EQ Frequency Hz: 60, 250, 1K, 4K, 12K
x Boost/Cut Control: +
/
-12dB
PMX840BT
x Bluetooth Wireless Music Streaming
x Works with Virtually Any Bluetooth Enabled Device
x (iPhone, Android, Smartphone, iPad, Tablet, PC, etc.)
x Digital LCD Display & Front Facing Control Center
x USB Flash Drive & SD Memory Card Readers
x 3-Pin Low Impedance Balanced Microphone Inputs
x 1/4'' Line/ High Impedance Balanced Inputs
x Independent Channel Volume, EQ & EFFX Controls
x Master 5 Band Graphic Equalizer
x EQ & Master EFFX Control of Level, Echo & Reverb Controls
x Aux (3.5mm) Input Jack for Connecting External Devices
x Headphone Output: 1/4'' TRS Stereo Connector
x RCA & 1/4'' Effects Loop Connectors
x Additional RCA Inputs: Tape Play (L/R), Tape Record (L/R)
Technical Specs:
x 800 Watt Output Power
x 8 Ohm Impedance Each Channel
x Line Level Impedance 10K Ohms @ -10dBv
x Mono Microphone Inputs (XENYX Mic Pre-Amp)
x XLR: Electronically Balanced Discrete Input Circuit
x Frequency Response: <10Hz150kHz (-1dB), <10Hz200kHz (-
3dB)
x Gain Range: +10 - +60dB
x Max. Input Level: +12dBu @ +10dB Gain
x Impedance: Approx. 2.6k Balanced
x Signal-to-Noise Ratio: 110dB / 112dBA Weighted
x Distortion: (THD+N): 0.005% / 0.004% A- Weighted
x Channel Equalization: Control Range
x High @ 10K +/-15dB, Low @ 60K +/-15dB
x Master EQ Frequency Hz: 60, 250, 1K, 4K, 12K
x Boost/Cut Control: +
/
-12dB
Pyle'PMX'SeriesMultiChannelMixers
www.PyleAudio.com
'PMX'MixerSeriesModels&Specifications:
PMX401
x 4-Channel System Power Mixer
x (4) Balanced Microphone Inputs
x (4) 1/4" Line/High Impedance Inputs
x RCA Audio Input & RCA Audio Output
x Aux (3.5mm) Input Connector Jack
x Audio Line-In: Connect Devices like Smartphones & MP3 Players
x 1/4” Send/Return Jacks & (2) Conductor 1/4” Speaker Outputs
x Built-In Reverb with Individual Channel Controls
x Master Effects Controls with Echo, Delay & Effects Volume
x Equalizer Control For Each Input
x Convenient Carry Handle
x Built-in Cooling Fan
Technical Specs:
x Maximum Power Output: 150 Watt / 4 Ohm
x Frequency Response: 20Hz - 20kHz +1dB
x (Lo-Z) Mic Impedance: 1K Ohm
x (Hi-Z) Mic/Line Impedance: 33K Ohm
x Impedance Gain
x Gain Range: +10 to +60dB
x Master EQ Control Ranges: +/- 12dB
x Channel Tone Adjustment: +/-15dB
x S/N Ratio: 110dB / 112dB A-Weighted
x Max. Input Level +12dBu @ +10dB Gain
x Distortion (THD+ N): 0.005% / 0.004%
x Power: 110/220 Voltage Switchable
x Dimensions: 12.9''W x 8.3''H x 10.5''D
PMX402M
x 4-Channel System Power Mixer
x (4) Balanced 3-Pin Microphone Inputs
x (4) 1/4'' High Impedance Inputs
x Aux (3.5mm) Input Connector Jack
x Connect iPod, MP3 Players, iPhone, Smartphones, Tablets, etc.
x Master System EFFX, EQ & Volume Controls
x 5-Band Graphic Equalizer
x USB Flash & SD Memory Card Readers
x LCD Digital Display Screen with Touch Button Controls
x Independent Channel EQ, Treble, Bass, Reverb Controls
x 1/4'' Send/Return Jacks & (2) Conductor ¼” Speaker Outputs
x RCA (L/R) Record Connector Jacks
x 1/4'' Headphone Output
x Convenient Carry Handle
x Built-in Cooling Fan
Technical Specs:
x Maximum Power Output: 400 Watts 4-Ohms
x Frequency Response: <10Hz - 150Hz (-1dB)
x Max. Input Level +12dBu @ +10dB Gain
x S/N Ratio: 110dB / 112dB A-Weighted
x Channel Tone Adjust (+/-15dB)
x Gain Range: +10 to +60dB
x Master EQ Control Ranges: +/- 12dB
x Distortion (THD+ N): 0.005% / 0.004%
x Power: 110/220 Voltage Switchable
x Dimension: 15.75'' x 12.01'' x 7.87''
PMX602M
x 6-Channel System Power Mixer
x (6) Balanced Microphone Inputs
x (6) 1/4" Line/High Impedance Inputs
x Aux (3.5mm) Input Connector Jack
x Connect iPod, MP3 Players, iPhone, Smartphones, Tablets, etc.
x Master System EFFX, EQ & Volume Controls
x 5-Band Graphic Equalizer
x USB Flash & SD Memory Card Readers
x LCD Digital Display Screen with Touch Button Controls
x Independent Channel EQ, Treble, Bass, Reverb Controls
x 1/4'' Send/Return Jacks & (2) Conductor ¼” Speaker Outputs
x RCA (L/R) Record Connector Jacks
x 1/4'' Headphone Output
x Built-in Cooling Fan
Technical Specs:
x Maximum Power: 600 Watt / 4 Ohms
x Frequency Response: <10Hz - 150Hz (-1dB)
x Max. Input Level +12dBu @ +10dB Gain
x S/N Ratio: 110dB / 112dB A-Weighted
x Channel Tone Adjust (+/-15dB)
x Gain Range: +10 to +60dB
x Master EQ Control Ranges: +/- 12dB
x Distortion (THD+ N): 0.005% / 0.004%
x Power: 110/220 Voltage Switchable
x Dimensions (L x W x H): 15.9" x 10.6" x 8.3"
PMX802M
x 8-Channel System Power Mixer
x (8) Balanced Microphone Inputs
x (8) 1/4" Line/High Impedance Inputs
x Aux (3.5mm) Input Connector Jack
x Connect iPod, MP3 Players, iPhone, Smartphones, Tablets, etc.
x Master System EFFX, EQ & Volume Controls
x 5-Band Graphic Equalizer
x USB Flash & SD Memory Card Readers
x LCD Digital Display Screen with Touch Button Controls
x Independent Channel EQ, Treble, Bass, Reverb Controls
x 1/4'' Send/Return Jacks & (2) Conductor ¼” Speaker Outputs
x RCA (L/R) Record Connector Jacks
x 1/4'' Headphone Output
x Built-in Cooling Fan
Technical Specs:
x Maximum Power: 800 Watt / 4 Ohms
x 125 Watt RMS x2 @8 Ohms
x Frequency Response: <10Hz - 150Hz (-1dB)
x Max. Input Level +12dBu @ +10dB Gain
x S/N Ratio: 110dB / 112dB A-Weighted
x Channel Tone Adjust (+/-15dB)
x Gain Range: +10 to +60dB
x Master EQ Control Ranges: +/- 12dB
x Distortion (THD+ N): 0.005% / 0.004%
x Power: 110/220 Voltage Switchable
x Dimensions: 20.28'' x 12.01'' x 7.87''
/