Sea gull lighting 69272BLE-46 Installation guide

Type
Installation guide
STEP 1:
FIGURE 1
*NOT SUPPLIED
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
a
nd create a potential safety hazard.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
If you are unclear as to how to proceed, contact a qualified
electrician.
Save these instructions.
IMPORTANT SAFETY INSTRUCTIONS
*OUTLET BOX
*OUTLET BOX
SCREWS
*WIRE
CONNECTORS
SCREW
COLLAR (E)
CANOPY (G)
MOUNTING
BAR (A)
*GROUND WIRE
CHAIN (H)
NUT (B)
SCREW COLLAR
RING (F)
FIXTURE LOOP (I)
GREEN
GROUNDING
SCREW (D)
NIPPLE (C)
N
OTE: This glass is handcrafted, the slight imperfections in the
glass add to the authenticity of the fixture.
Attach break assembly to shade by threading nipple (J) onto coupling (L)
(if applicable).
Secur
e in place by threading loop (I) onto nipple (J).
Carefully remove the fixture from the carton and check that all parts are
included, as shown in figure 1 and 2. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
Pass fixture wires thru break assembly (K) (if applicable).
1. Remove the 3 retaining screws, and remove the cage.
2. Remove the cardboard packaging.
3. Replace cage and screws.
IF APPLICABLE: TO REMOVE THE PACKAGING
ASSEMBLY
STEP 2:
STEP 3:
COUPLING (L)
NIPPLE (J)
BREAK
ASSEMBLY (K)
Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
HC-1613
0
82109
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
BEFORE YOU BEGIN
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
CLEANING
ORDERING PARTS
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Thread nut (B) on nipple (C) so that 3 threads are exposed
above nut (B). Thread nipple (C) into mounting bar (A) and secure
with nut (B). Thread screw collar (E) to nipple (C).
STEP 1:
U
sing 2 pairs of pliers, open one link of chain (S) and connect it to
the fixture loop (J) at the top of the fixture.
STEP 2:
STEP 3:
INSTALLATION HC-1613
S
lide the screw collar ring (F) and canopy (G), in that order, over
chain (H). Open one link on the other end of the chain (H) and attach
it to the screw collar (E) which has been mounted to the ceiling
nipple (C).
BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
A
fter wires are connected, tuck them carefully inside outlet box.
Raise canopy (H) against ceiling and thread the screw collar ring (G)
to the screw collar (E).
Make sure no bare wires can be seen outside wire connectors.
I
nstall self ballasted lamp (M) into socket (N) by gently twisting into
place.
FINAL ASSEMBLY
STEP 6:
S
TEP 7:
GROUNDING INSTRUCTIONS:
Connect the supply ground wire, fixture ground wire, and mounting
bar ground wire (pre attached) using the supplied wiring connector.
Gently try to remove the wires from the connector. If you can remove
the wires, carefully re-do the wiring connection.
STEP 4:
STEP 5:
A. Use a listed wire connector to connect the fixture hot wire (black
wire, or round and smooth tracer) to the supply hot wire.
B. Use a listed wire connector to connect the fixture common wire
(white wire, or square and rigid) to the supply common wire.
C. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do the wiring connection.
Hg
MARK MEANS LAMP CONT
AINS MERCUR
Y
.
FOLLOW DISPOSAL LAWS.
SEE WWW.LAMPRECYCLE.ORG
FIGURE 2
FIXTURES WITH A ONE PIECE
LAMP / BALLAST COMBINATION
SELF
BALLASTED
LAMP (M)
SOCKET (N)
  • Page 1 1
  • Page 2 2

Sea gull lighting 69272BLE-46 Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI