Generation Lighting 61625 Installation guide

Brand
Generation Lighting
Model
61625
Type
Installation guide

This manual is also suitable for

Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
FIGURE 1
*NOT INCLUDED
BEFORE YOU BEGIN
Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
HC-1580
0
91009
• Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
• Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
• If you are unclear as to how to proceed, contact a qualified
electrician.
• You don’t need special tools to install this fixture.
• Be sure to follow the steps in the order given.
• Read instructions carefully.
• Save these instructions.
IMPORTANT SAFETY INSTRUCTIONS
Feed the fixture wire through the fixture loop (F) and thread fixture
loop (F) to top of the socket assembly (U).
STEP 1:
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
CLEANING
ORDERING PARTS
Feed the fixtur
e wir
e fr
om the socket assembly (U), thr
ough: the r
od
assembly (E) and thr
ead r
od assembly (E) into socket assembly (U). If
using optional chain, thread coupling at one end of chain into rod
assembly (E) or socket assembly (U).
Assemble r
od assembly (E) by thr
eading desired amount of r
ods
together
.
Secur
e mounting bar (A) to outlet box using outlet box scr
ews (not
supplied). Thr
ead nut (C) onto nipple (I) so five threads ar
e exposed.
Thread nipple (I) to mounting bar (A) and secure by tightening nut (C)
to mounting bar (A). Thread screw collar (B) to nipple (I).
INSTALLATION
STEP 1:
STEP 2:
STEP 3:
*OUTLET BOX
*WIRE
CONNECTORS
CANOPY (G)
NIPPLE (I)
SHADE (R)
COUPLING (J)
ROD ASSEMBLY (E)
RET
AINING RING (T)
MOUNTING
BAR (A)
SCREW COLLAR
RING (K)
SCREW COLLAR (B)
NOTE: THIS FIXTURE
CAN BE HUNG USING
1, 2, OR 3 RODS.
SELECT THE NUMBER
OF RODS DESIRED.
GREEN GROUNDING
SCREW (D)
SOCKET
ASSEMBLY (U)
NUT (C)
IMPOR
TANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
FIXTURE
LOOP
(F)
Hg
MARK MEANS LAMP CONTAINS MERCURY.
FOLLOW DISPOSAL LA
WS.
SEE WWW.LAMPRECYCLE.ORG
After wires are connected, tuck them carefully inside outlet box and
then raise the canopy (G) against the ceiling. Secure by threading
screw collar ring (K) onto screw collar (B).
Make sure no bare wires can be seen outside wire connectors.
Install self ballasted lamp (O) by twisting into socket (P).
Place shade (R) securely in socket assembly (U). Secure by
threading retaining ring (T) onto socket (P).
FINAL ASSEMBLY
STEP 7:
STEP 8:
STEP 9:
STEP 6:
GROUNDING INSTRUCTIONS
:
Connect the supply ground wire, fixture ground wire, and mounting bar
ground wire (pre attached) using the supplied wiring connector. Gently try
to remove the wires from the connector. If you can remove the wires,
carefully re-do the wiring connection.
FIGURE 2
*NOT INCLUDED
*OUTLET BOX
*WIRE
CONNECTORS
CANOPY (G)
NIPPLE (I)
SHADE (R)
COUPLING (J)
ROD ASSEMBLY (E)
RET
AINING RING (T)
MOUNTING
BAR (A)
SCREW COLLAR
RING (K)
SCREW COLLAR (B)
NOTE: THIS FIXTURE
CAN BE HUNG USING
1, 2, OR 3 RODS.
SELECT THE NUMBER
OF RODS DESIRED.
GREEN GROUNDING
SCREW (D)
SOCKET
ASSEMBLY (U)
NUT (C)
I
NSTALLATION (continued) HC-1580
A
.
U
se a listed wire connector to connect the fixture hot wire (black
wire, or round and smooth tracer) to the supply hot wire.
B
.
U
se a listed wire connector to connect the fixture common wire
(white wire, or square and rigid) to the supply common wire.
C. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do the wiring connection.
STEP 5:
WIRING
CHAIN (M)
Slide screw collar ring (K) and canopy (G) (in that order) to top of
socket assembly (U). Be sure not to damage the fixture wire. Thread
r
od assembly (E) or chain coupling to nipple of the coupling (J) at the
screw collar.
STEP 4:
FIGURE 3
FIXTURES WITH A ONE PIECE
LAMP / BALLAST COMBINATION
SELF BALLASTED
LAMP (O)
SOCKET (P)
  • Page 1 1
  • Page 2 2

Generation Lighting 61625 Installation guide

Brand
Generation Lighting
Model
61625
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents