SkyLink SK-4 User manual

Brand: SkyLink

Model: SK-4

Category: Dimmers

Type: User manual

This manual is also suitable for

2.SETUP

3. PROGRAMMINGTRANSMITTERSSENSORS

There are 3 operating modes with the :

In order to operate the remotely with a transmitter or sensor,

it must be programmed to the . Each module can be operated

by up to 8 different transmitters (or 8 different command signals).

1) Regular Mode - When a valid signal is received, it will turn on or off the

light, or change the brightness of the light.

2) Flashing Alert Mode - When a valid signal is received, the light will flash

for a specific period of time, which is the time defined in the timer duration.

This works as an alert indication.

3) Countdown Timer Mode - When a valid signal is received, the light will

be on for a specific period of time, 1 minute, 5 minutes, 15 minutes,

30 minutes, or 60 minutes. This is mainly for energy saving.

Wall Dimmer

Youcanprogrammultiplebuttons/transmitters/sensorstothemodule

anddifferentbutton/transmitter/sensorcanactivateadifferentmode.

Touchthetouch

pad.

ToprogramatransmitterintotheWallSwitchDimmer,followthe

instructionsbelow:

BeforeyouprogramatransmittertotheWallDimmer,decidethe

operatingmodeforthistransmitter(RegularMode,Flashing AlertMode

orCountdown TimerMode).

1.WallDimmermustbeinstalledandpoweredproperly.

Theconnectedlightshouldbeon,andthe2blueLEDsareoff.

2.Pressandholdthe"SET"buttonforabout3seconds,theupperblue

LEDflashesquickly,meaningitisinRegularModeprogramming

sequence.Releasethe"SET"buttonifyouareprogramminga

transmittertooperateinOn/OffMode.

Note:Useasharpnon-conductiveobjecttopresstheSET button.

Changingthestateoftheloadbythe TouchPadwhilepressingtheSET

buttonwillinterferethelearningprocess.

3.IfyouareprogrammingatransmittertooperateinFlashing AlertMode,

continuetoholdthe"SET"buttonforabout10seconds,untiltheupper

blueLEDflashesslowly,thenreleasethe"SET"button.

4.IfyouareprogrammingatransmittertooperateinCountdown Timer

Mode,continuetoholdthe"SET"buttonforabout10seconds,until

theupperblueLEDisonsteadilyon,thenreleasethe"SET"button.

5. Transmita"Learn"codefromthetransmitter.Refertothemanualof

thetransmittertotransmitthis"Learn"code.

6.Oncethetransmitterisprogrammed,thebothblueLEDsflashquickly

thenstopsflashing. Youhavesuccessfullyprogrammedthetransmitter.

OperatingMode

Regular

Flashing Alert

TimerCountdown

UpperLEDIndication

Flashesquickly

Flashesslowly

SteadilyOn

1.INTRODUCTION

ModelWR-001

WallDimmer

Thankyouforyourpurchaseofa ,Wall

Dimmer,ModelWR-001.Simplyreplaceyourexistingwallswitchwiththis

WallDimmer,youcanthenwirelesslyturnonandoff,dimandbrighten

lightswitha transmitter.

TheWallDimmerWR-001cancommunicatewithupto8transmitters,so

userhastheoptiontoaddmoretransmitterstothesystem,suchasmore

remotecontrols,ormotionsensorsetc.

Allwirelesssignalcommunicationswithinthe Systemare

basedonrollingcodetechnologytoensurehighestsecurityisused.

Thefollowingitemsareincludedinthispackage:

-WallDimmer

-Wirenuts

SkylinkHome lightingreceiver

SkylinkHome

User’sInstructions

Wall Dimmer

WR-001

Wirenuts

Note:

Antenna --Donotcutit,keepitasstraightaspossible.

Puttheantennadirectlyintothedrywallorthroughaholeofthe

metalboxintothedrywalltogetmorecontroldistancewitharemote.

(greywire)

Note: You must complete the programming sequence within the 15-second

interval, otherwise, the Wall Dimmer will quit from programming mode and

you need to start again from step 1.

4.SETTIMERDURATION

This section is for transmitters that are programmed for Flashing Alert

Mode and Countdown Timer Mode.

The timer for both Flashing Alert Mode and Countdown Timer Mode can

be set to the following duration, meaning the light will stay on for the

following time: 1 minute, 5 minutes, 15 minutes, 30 minutes, or 60 minutes.

Only one timer interval can be set. To set the timer duration, follow the

instructions below.

1. Wall Dimmer must be installed and powered properly. The connected

light should be off, and the 2 blue LEDs are on. The light must

be off in order to set the timer duration.

2. Press and hold the SET button for 3 seconds, the lower blue LED

flashes once. The number of flashes indicates the timer duration:

Red

Load

Black

Live

AirGap

Switch

Touch

Pad

SET

Button

Blue

LEDs

Grey Antenna

Donotcuttheantenna!

Green

Ground

(Usuallycopper

orgreen)

OFF

incandescentlightordimmable

compactfluorescentlightwithamaximumload Light

bulbsmustbedimmableinordertoachievedimmingfunction.

respectivelytotheexistingwiresfromthewall:

SecuretheWallDimmerwiththeprovidedscrews.

ThetwoblueLEDswillbeon.

tapthemetaltouchpad toturnON/OFFtheconnectedlightor

SetupoftheWallDimmerissimple.Simplyreplaceyourexistingwall

switchbytheWallDimmer.

1. TurnoffpowertothecircuitthatyouplanoninstallingtheWallDimmer

to .

Note:LightingLoad

TheWallDimmerisdesignedtooperate

of300Wat120VAC.

2.FollowthediagramsbelowtoinstalltheWallDimmerwiththe2wires:

Live,Load.Usetheprovidedwirenutstoconnectthesewires

3. Afterallthewiresareconnected,ensurethatallofthewireconnectors

areattachedsecurelyandthereshouldbenoexposedcopperwiring.

4.Placetheairgapswitchtooffposition.

5. Turnthecircuitbreakerbackon.

6.Placetheairgapswitchtoonposition.

Note:Ifthe2blueLEDsremainoff,pleasecheckandensurethelight

bulbisinstalledandingoodcondition.

7. Thelightconnectedwillbeoff. TheWallDimmerisnowinstalledand

youcan

beginprogrammingtolearntransmittersintotheWallDimmer.

CAUTION

Installationisrequiredandenclosedinstructionsmustbefollowed

carefullytoallstepsandnotes.Ifyouareuncertainoruncomfortable

performingthisinstallation,pleaseconsultaqualifiedelectrician.

Thismanualshouldalsoberetainedforfuturereference.

WARNING

Failuretoturnoffpoweratthecircuitbreakercanresultinelectrical

shockcausingsevereorfatalinjury.

atthecircuitbreaker

Load(red)toloadand

Live(Black)tolive.Ground(Green)toGround.

OFF

Ground(Green)toGround

5.REGULAR OPERATINGMODE

5.REGULAR OPERATINGMODE(CONT)

The cancontrolthelightin2differentoperatingmodes:

1)On/OffMode- Allowsoperatingthelighteitheronoroff,without

dimmingfunction.

2)DimmingMode- Allowsoperatingthelightinon,offordimming

(dim/brighten).Lightsourcemustbeeitherincandescentlight

ordimmablecompactfluorescentlight.

WallDimmer

1. Turnonthelightbytheprogrammedtransmitterortouchpad.

2.Pressandholdthebuttononthetransmitterthatisprogrammedto

the in“Regular”modefor10seconds

3. Thelightwillflash.Ifitflashesonce,thatmeansitisinOn/OffMode.

Ifitflashestwice,thatmeansitisinDimmingMode.

4.Repeatingstep2abovewilltogglethesettingbetweenOn/OffMode

andDimmingMode.

ThefactorydefaultoperatingmodeisOn/Offmode.However,ifyour

lightisdimmable,youmaychangetheoperatingmodetoDimming

Mode. Tochangetheoperatingmodes,pleasefollowtheinstructions

below:

WallDimmer ortouchthetouch

padfor10secondswithyourfinger.

5.1ON/OFFoperation:

UseaTransmitter

WallDimmer allowson/offoperation,whentheprogrammedbuttonis

pressed,itwilltransmitasignaltotogglethestatusoftheload.

Forexample,ifatogglesignalisreceivedwhenthelightisoff,thatsignal

willturnonthelight.

5.2Brightnesscontroloperation:

6.FLASHING ALERTOPERATINGMODE

Besides turning on and off the light, you may also control the brightness

of the light if the light bulb is either incandescent light or dimmable compact

fluorescent light.

Turn on the light first. Then keep touching the touch pad to change the

brightness. Remove your finger from the until the desired

brightness is reached. To change the the opposite way,

remove your finger from the and then keep touching

First turn on the light. Then p

Use the Wall Switch

Use a Transmitter

touch pad

ress and hold the programmed button on the

transmitter to change the brightness. Hold the button until the desired

brightness is reached, then release the button.

Press and hold the same button again on the transmitter to change the

brightness again in the opposite way. When the desired brightness is

reached, release the button.

Refer to the user's instructions of the transmitter for more detailed

instructions for dimming operation, as well as other operations such as

Zone On / Zone Off, Zone Dimming, All On / All Off etc.

brightness in

again,

remove the finger from the touch pad until the desired brightness is reached.

Note: Press and hold for more than 10 seconds will toggle the mode

between ON/OFF and Dimming.

Note: If the 2 blue LEDs are off when the loading is off, please check and

ensure the light bulb is installed and in good condition.

IfaFlashing AlertModetransmitterorsensorisactivated,thelight

connectedtotheWallDimmerwillflashforapredeterminedtimeinterval.

Duringtheflashinginterval,theupperblueLEDontheWallDimmerwill

flash,thelowerblueLEDwillstarttoflashduringthelastminute

ofthecountdowntimer. Activatingaprogrammedtransmitterorsensor

underRegularModeorCountdown TimerModeduringflashinginterval

canoverrideflashingalertoperation.

UsetheWallDimmer

Toturnon/offthelight,simplytapthetouchpadofthewalldimmer

oncewithyourfinger,itwilltogglethestatusofthe light,i.e.fromonto

offorfromofftoon.

Note:Oncethenumberofflashesreaches5,itwillstayatthissetting.If

youwouldliketogobacktoothersettings,suchas1minute,releasethe

buttonand repeatfromstep1tostartover.

Onceatransmitter(button)isprogrammedfortimermodeorflashing

mode,activatingthisprogrammedtransmitter(button)willturnonthe

lightforthespecifiedtimerduration.

Duringatimercountdown,iftheWallDimmerreceivesanothersignalfor

timer operation,thetimerwillstartagainandoverridestheprevioustimer,

therefore,extendingtheOnperiodbyanothertimerinterval.

Tostoptimercountdown,pressaprogrammedbutton forregularmode.

4.SETTIMERDURATION(CONT)

WARNING

Non-dimmableloadhastobealwaysworkingunderON/OFFmode.

Usingnon-dimmableloadunderdimmingmodemaydamagethe

non-dimmableCFL.

NumberofFlashes

TimerDuration

1min.

5 min.

15min.

30min.

60min.

3. Continue to hold the SET button until it reaches the desired setting. The

status will change every 6 seconds, i.e. hold the SET button for another

6 seconds, you will see the number of flashes changes from 1 to 2, 2 to

3, etc.

7.COUNTDOWNTIMEROPERATINGMODE

If a Countdown Timer Mode transmitter or sensor is activated, the light

connected to the Wall Dimmer will be on for the predetermined time interval.

During the timer count down, the upper blue LED on the Wall Dimmer will

be on steadily, the lower blue LED will start to flash during the last minute

of the countdown timer. Activating a programmed transmitter or sensor

under Regular Mode or Flashing Alert Mode during timer interval can over-

ride the countdown timer operation.

8. ERASINGTRANSMITTERSFROMTHEMODULE

Youmayeraseatransmitterorsensorfromthewalldimmer,butyou

cannoteraseaspecificdevicedirectly,youmusteraseallthewireless

devices,thenprogramtheonesyouwanttokeep.Followtheinstructions

belowtoeraseprogrammedtransmitters/sensors.

1.PowerofftheWallDimmerbyplacingtheairgapswitchtooffposition.

2.PressandholdtheSET button,whileholdingtheSET button,slidethe

airgapswitchtoonposition.

3. TheblueLEDswillbeonfirst,thenturnoff.

4. YoumayreleasetheSET button,nowyouhavesuccessfullyerasedall

thedevices.

Note:Useasharpnon-conductiveobjecttopresstheSET button.

Changingthestateoftheloadbythe TouchPadwhilepressingtheSET

buttonwillinterferethelearningprocess.

InputVoltage:120V AC,60Hz

MaximumLoad:300Wat120VAC

OperatingFrequency:318MHz

Range:Upto500feetinopenarea

StandbyCurrent:0.2mA

MinimumLoad:10W

Operational Temperature:-4°F-140°F

(-20°C-60°C)

Humidity:5%-95%

9. TECHNICAL SPECIFICATIONS

Note:Useasharpnon-conductiveobjecttopresstheSET button.

Changingthestateoftheloadbythe TouchPadwhilepressingtheSET

buttonwillinterferethelearningprocess.

11.FCC

TheDeviceisapprovedbytheFCCanditcomplieswithPart15oftheFCCRules.

Itsoperationissubjecttothefollowingtwoconditions:

1. Thisdevicemaynotcauseharmfulinterference.

2. Thisdevicemustacceptanyinterferencethatmaycauseundesiredoperation.

Changesormodificationsto thisunitnotexpresslyapprovedbythepartyresponsible

ofcompliancecouldvoidtheuser’sauthoritytooperatetheequipment.

WARNING:

CUSTOMERSERVICE

17Sheard Avenue,Brampton,Ontario,CanadaL6Y 1J3

Email:[email protected]

http://www.skylinkhome.com

P/N.101Z713-004

PatentPending

12.WARRANTY

If,withinoneyearfromdateofpurchase,thisproductshouldbecomedefective

(exceptbattery),duetofaultyworkmanshipormaterials,itwillberepairedor

replaced,withoutcharge.ProofofpurchaseandaReturn Authorizationarerequired.

13.CUSTOMERSERVICE

14. ACCESSORIES

TheSkylink Systemconsistsofmanyotherdevicessuchas

SkylinkHome Remotes,MotionSensor,ON/OFFWallSwitch,Wall

Dimmer,Plug-InDimmerwithorwithoutRepeater,Plug-InON/OFF

Control(Outdoor/Indoor),Screw-InDimmer,ON/OFF/DimmingControl,

ON/OFFControl,SmartButton GarageDoorControl,etc.Pleasevisit

Skylinkwebsiteat formoreinformation.www.skylinkhome.com

Home

Ifyouwouldliketo

- findouttheup-to-datespecifications

- knowmoreaboutfeaturesandapplications

- downloaddocuments,i.e.user’sinstructions

- orderSkylinkproducts

orifyouhavedifficultygettingproductstowork,please:

1.visitourFAQsectionat ,or

2.emailusat ,or

3.callourtollfreeat1-800-304-1187fromMondaytoFriday,9amto5pmEST.

Fax(800)286-1320

www.skylinkhome.com

[email protected]

10.WiringDiagram

WiringDiagramw/oNeutralWire

WiringDiagramwithNeutralWire

SkyLink SK-4 User manual

Brand: SkyLink

Model: SK-4

Category: Dimmers

Type: User manual

This manual is also suitable for

Download PDF

report

SkyLink SK-4 User manual

This manual is also suitable for

SkyLink SK-4 User manual

Related papers

Other documents