Renkforce Ultra Slim Connection Box Compatible Owner's manual

Ultra Slim Connection Box Compatible
Renkforce
Brand
Renkforce
Model
Ultra Slim Connection Box Compatible
Type
Owner's manual

Renkforce Ultra Slim Connection Box Compatible allows for easy and secure connection of network cables, featuring TIA/EIA T568A and T568B wiring schemes, supporting various cable diameters, and ensuring reliable data transmission in different network setups.

Renkforce Ultra Slim Connection Box Compatible allows for easy and secure connection of network cables, featuring TIA/EIA T568A and T568B wiring schemes, supporting various cable diameters, and ensuring reliable data transmission in different network setups.

Instruction Manual
Remove the before installation.wiring cap
Insert cable into strain relief boot, strip off 1.2 inch
of cable jacket ,fold back braid and drain wire.
Unload the cable
Cut off cable tie, remove the boot. Using flat screw driver and pry gently
on cover one end first and the other end subsequently to open it.connection module
1
2
1,2 mm"(30 )1,2 mm"(30 )
Place wiring cap on connection module.
Place the wiring cap onto ,use plier
to clamp wiring cap until it completely snap-in to effect
the connection.
connection module
4
5
Fan out all four twisted pairs, following the color coding label and allocate each
conductor into proper slots on wiring cap. Trim the ends of conductors.
3
Wiring label
Close cover, make sureconnection module the drain wire is in proper contact with grounding clip on
connection module.Pull back strain relief boot to cover the connection module, fasten supplied cable tie
to secure grounding contact.
6
Cable tie
Cut off cable tie
Open cap
Boot adjustment
Cut the end of boot to fit your
cable OD.
White/Brown
Brown
JACK PIN
DESIGNATIONS
TIA/EIA
T568A
TIA/EIA
T568B
White/Green
Green
white/Orange
Orange
white/Orange
Blue
White/Green
Blue
white/Blue
Orange
white/Blue
Green
White/Brown
Brown
Drain Wire
Drain Wire
Instruction Manual
Remove the before installation.wiring cap
Insert cable into strain relief boot, strip off 1.2 inch
of cable jacket ,fold back braid and drain wire.
Unload the cable
Cut off cable tie, remove the boot. Using flat screw driver and pry gently
on cover one end first and the other end subsequently to open it.connection module
1
2
1,2 mm"(30 )1,2 mm"(30 )
Place wiring cap on connection module.
Place the wiring cap onto ,use plier
to clamp wiring cap until it completely snap-in to effect
the connection.
connection module
4
5
Fan out all four twisted pairs, following the color coding label and allocate each
conductor into proper slots on wiring cap. Trim the ends of conductors.
3
Wiring label
Close cover, make sureconnection module the drain wire is in proper contact with grounding clip on
connection module.Pull back strain relief boot to cover the connection module, fasten supplied cable tie
to secure grounding contact.
6
Cable tie
Cut off cable tie
Open cap
Boot adjustment
Cut the end of boot to fit your
cable OD.
White/Brown
Brown
JACK PIN
DESIGNATIONS
TIA/EIA
T568A
TIA/EIA
T568B
White/Green
Green
white/Orange
Orange
white/Orange
Blue
White/Green
Blue
white/Blue
Orange
white/Blue
Green
White/Brown
Brown
Drain Wire
Drain Wire
  • Page 1 1

Renkforce Ultra Slim Connection Box Compatible Owner's manual

Ultra Slim Connection Box Compatible
Renkforce
Brand
Renkforce
Model
Ultra Slim Connection Box Compatible
Type
Owner's manual

Renkforce Ultra Slim Connection Box Compatible allows for easy and secure connection of network cables, featuring TIA/EIA T568A and T568B wiring schemes, supporting various cable diameters, and ensuring reliable data transmission in different network setups.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents