Chariot Carriers 51100605 User manual

Brand: Chariot Carriers

Model: 51100605

Category: Strollers

Type: User manual

Chariot Carriers 51100605 is a strolling kit that can quickly transform your existing Chariot trailer into a stroller without the need for additional tools. It features:

A parking brake to keep the stroller stationary when parked.
A wrist safety strap to prevent the stroller from rolling away.
Adjustable handlebars for a comfortable grip.
Easy-to-install wheels with a locking mechanism for added safety.
A compact design for easy storage and transportation.

Chariot Carriers 51100605 is a strolling kit that can quickly transform your existing Chariot trailer into a stroller without the need for additional tools. It features:

A parking brake to keep the stroller stationary when parked.
A wrist safety strap to prevent the stroller from rolling away.
Adjustable handlebars for a comfortable grip.
Easy-to-install wheels with a locking mechanism for added safety.
A compact design for easy storage and transportation.

CLASSIC STROLLING CTS KIT

Rev. 06/13/06 www.ChariotCarriers.com 51100605

WARNING!

• Use wrist safety strap at all times.

• Always use seat belts.

• Always use parking brake when stroller is stationary.

• Never in-line skate with the Strolling Kit. A serious accident could occur

resulting in serious injury or death.

Initial Assembly Time: About 5 minutes.

Tools Required: A 7/16" and a 1/2" open end or adjustable wrench.

Note: Bolts must be securely fastened, but not over tightened.

A. Parking Brake Assembly Figure 1.

1. Place the carrier on a clean surface, turn it upside down so that the

wheels point upwards, and stand behind the trailer.

2. Using a 7/16" wrench, remove the uppermost ¼" locknut from each of the

two brake bolts. The brake bolts are the longer bolts, which are the bolts

closest to the rear of the trailer.

3. On the brake assembly, remove the 5/16" locknut from the bolt with the

exposed threads using a ½" wrench.

4. Orient the brake assembly so that the long arms are pointing straight out

to each side. The small arm should point towards the rear of the carrier

and the plastic handle should point downwards, while the Carrier is upside

down. Pivot the curved arm so that the plastic handle is on your left hand

side.

5. Place the grommeted end of the wrist safety strap onto the bolt with the

exposed threads. Insert the bolt down through the hollow plug at the

centre of the rear of the Carrier. Securely fasten the 5/16" locknut onto

the bolt inside the rear storage compartment using a ½" wrench.

IMPORTANT: The plastic handle must be located behind the carrier,

not underneath.

IMPORTANT: When using in trailer mode, you must tuck the trailing

end of the wrist safety strap into the cargo area of the carrier.

6. Place the holes in the long arms down onto the brake bolts from which the

¼" locknuts were removed and securely fasten the ¼" locknuts onto each

bolt using a 7/16" wrench. The secured bolt should extend into the nylon

portion of the locknut.

7. Turn the carrier back over so it is resting on both wheels.

B. Handlebar Assembly See Parts List Diagram.

1. Insert both ends of the handlebar into the aluminum extensions located at

the upper rear section of the carrier.

2. Depress both spring buttons and insert both handlebar ends fully into the

extensions. Both spring buttons must 'pop' out the holes located on

the inner side of the extensions to secure the handlebar into place.

Note: The handlebar height is adjustable. Simply remove the handlebar,

rotate it 180°, and re-insert the handlebar into the extensions.

WARNING!

• Failure to properly install the handlebar or use the wrist safety

strap could cause the trailer to become separated from you,

resulting in an accident and serious injury.

C. Wheel Assembly See Parts List Diagram.

1. Remove the wheel arms or any other kit component from the wheel arm

attachment bracket.

2. Push the button located on the side of the wheel arm attachment bracket

as far in as possible. This will create an opening for the caster shaft.

3. While maintaining the button depressed, slide the stroller caster from the

bottom up into the wheel arm attachment bracket.

4. When fully inserted, release the button and it will return to its closed and

locked position. To make sure the caster is secured, test by trying to pull

the caster downwards.

5. Repeat with the other wheel.

WARNING!

• Failure to properly attach wheels could cause the wheels to fall off,

resulting in an accident and serious injury.

• Direct impacts against the pivoting stroller wheels could cause

damage to the hitch arm attachment brackets.

WARNING!

Failure to comply with the manufacture's instructions can lead to serious

injury or death of the passenger/rider.

OPERATING INSTRUCTIONS

A. Seat Belt Instructions

1. Follow instructions located in your Cabriolet CTS and Corsaire XL owner's

manual.

WARNING!

• Failure to use seatbelts, at all times, could result in serious injury.

B. Parking Brake Instructions

Note: Any reference to left or right is from the trailer passengers' point of

view, while inside the carrier.

1. Engage parking brake by pivoting the plastic handle of the brake

assembly, located down low behind the carrier, from the right to the left

hand side of the carrier until it 'snaps' into place against the frame.

2. Disengage parking brake by pivoting the plastic handle from the left all the

way back to the right hand side of the carrier. The plastic handle must

rest against the carrier frame to prevent the parking brake from contacting

the tires.

WHEEL STORAGE AND STROLLER DISASSEMBLY

1. To store the wheel on the trailer, turn the wheel assembly upside down

angled towards the back of the carrier.

2. While maintaining the button depressed, slide the wheel down from the

top of the wheel arm attachment bracket into the opening.

3. When fully inserted, release the button and it will return to its closed and

locked position. To make sure the caster is secured, test by trying to pull

the caster downwards.

IMPORTANT: When using in stroller mode all cargo should be stored

in the foot well of the carrier. At no time should any cargo be stored

in the rear of the carrier.

Figure 1

PARTS LIST

# PART QUANTITY

A 40101306 Handlebar ........................................................... 1

B 50101817 Foam Grip ........................................................... 2

C 40202023 Wrist Safety Strap............................................... 1

D 50101702 Plastic Wheel - 8"................................................ 2

E 40101809 Caster Assembly................................................. 2

F 40101903 Brake Assembly.................................................. 1

G 50100713 Nylon Lock Nut - 5/16" ........................................ 1

Page is loading ...

Chariot Carriers 51100605 User manual

Brand: Chariot Carriers

Model: 51100605

Category: Strollers

Type: User manual

Chariot Carriers 51100605 is a strolling kit that can quickly transform your existing Chariot trailer into a stroller without the need for additional tools. It features: