LG PRDSBM Owner's manual

Type
Owner's manual

This manual is also suitable for

LG PRDSBM is an outdoor fault contact device that can be used to connect the main outdoor PCB to the outdoor unit. It has three terminals (DRY1, DRY2, GND) that can be connected to the corresponding terminals on the main outdoor PCB using communication cables with a thickness of 1.25 mm2. The maximum communication line length is 300 meters. The device should be installed by authorized personnel in accordance with national wiring standards.

LG PRDSBM is an outdoor fault contact device that can be used to connect the main outdoor PCB to the outdoor unit. It has three terminals (DRY1, DRY2, GND) that can be connected to the corresponding terminals on the main outdoor PCB using communication cables with a thickness of 1.25 mm2. The maximum communication line length is 300 meters. The device should be installed by authorized personnel in accordance with national wiring standards.

Representative: LG Electronics Inc. EU Representative, Krijgsman 1, 1186 DM Am-
stelveen, The Netherlands
Manufacturer: LG Electronics Inc. Changwon 2nd factory, 84, Wanam-ro, Seongsan-gu,
Changwon-si, Gyeongsangnam-do, KOREA
P/NO : MFL67525609
Please read this installation manual completely before installing the product.
Installation work must be performed in accordance with the national wiring standards by
authorized personnel only.
Please retain this installation manual for future reference after reading it thoroughly.
PRDSBM
INSTALLATION MANUAL
AIR
CONDITIONER
ENGLISH
PORTUGUESE
MALTI
ITALIANO
MAGYAR
SLOVENČINA
ESPAÑOL
БЪЛГАРСKN
SLOVENŠČINA
FRANÇAIS
SRPSKI
LATVIEŠU VALODA
DEUTSCH
HRVATSKI
LIETUVIŲ KALBA
ΕΛΛΗΝΙΚΆ
SVENDKA
GAEILGE
ČEŠTINA
NORSK
МАКЕДОНСКИ
NEDERLANDS
SUOMI
SHQIP
POLSKI
DANSK
ÍSLENSKA
LIMBA ROMÂNĂ
EESTI KEEL
BOSANSKI
Manual de instalare Contact fals exterior (PRDSBM)
1. Verificaţi conţinutul Contactului fals exterior (PRDSBM).
2. Conectaţi PCB exterior principal și Contactul fals exterior
-
Conectaţi bornele (DRY1, DRY2, GND) din partea din spate a contactului fals exterior
la bornele (DRY1, DRY2, GND) de la exterior conform imaginii de mai jos.
<Corp principal Contact fals exterior>
<Carcasă faţă>
3.
Contactul fals exterior combinat cu cutia de distribuţie conform imaginii de mai jos
h Lungimea liniei de comunicare poate fi de maxim 300 m, folosiţi cabluri de comunicare cu
grosimea de 1,25 mm
2
.
4. Atașaţi carcasa frontală
Aveţi grijă la cablare când Butonul apăsare din partea din spate a Contactului fals
exterior este apăsat iar cablurile sunt scoase.
ATENŢIE
!
1
2
3
4
1
2
3
4
indică cablajul pe teren
cablaj conectat
< PCB principal exterior >
<Parte din spate Contact fals exterior>
Buton apăsare
- Metodă de introducere cablu -
Apăsaţi în direcţia săgeţii.
Introduceţi cablul la conector.
Cutie de distribuţie
DRY1
DRY2
GND
DRY1 DRY2 GND
LIMBA ROMÂNĂ
  • Page 1 1
  • Page 2 2
  • Page 3 3

LG PRDSBM Owner's manual

Type
Owner's manual
This manual is also suitable for

LG PRDSBM is an outdoor fault contact device that can be used to connect the main outdoor PCB to the outdoor unit. It has three terminals (DRY1, DRY2, GND) that can be connected to the corresponding terminals on the main outdoor PCB using communication cables with a thickness of 1.25 mm2. The maximum communication line length is 300 meters. The device should be installed by authorized personnel in accordance with national wiring standards.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages