BDI ARENA 9970 Assembly Instructions Manual

Brand: BDI

Model: ARENA 9970

Type: Assembly Instructions Manual

bdiusa.com

customerservice@bdiusa.com

ARENA

9970

CABINET MOUNT

Your Arena Flat Panel Mount is engineered for easy assembly.

Carefully follow this procedure to prevent any damage.

Placement and Maintenance

Arena Flat Panel Mount is designed for indoor use and only on BDI

cabinets. Clean steel parts with a moist cloth.

Step 1

Unpack and identify the components at left. The assembly

workspace should be a non-marring surface such as carpet. For

missing hardware pieces, please contact BDI Customer Service at

[email protected].

For all other concerns, please contact your BDI Retailer.

Step 2

Measure the height of your BDI AV cabinet (not including

the base) to determine if the mount riser N is needed.

If your cabinet height is:

• 16-18.5” (less than 47cm) then proceed to Step 3A

(Avion, Nora, Marina, and Mirage)

• 18.5-21” (more than 47cm) then proceed to Step 3B

(Corridor, Elements)

These distinctive product conﬁgurations are protected by US and international patents,

trade dress, and/or copyright laws. Arena and BDI are trademarks of Becker Designed, Inc.

A - 5mm Allen Wrench x 1

I - Vertical Mounting

Bracket x 2

F - Horizontal Mounting

Bracket x 1

E -

x 1-

in Screws x 4

G -

in Screws x 4

D - Swiveling Bracket

Assembly x 2

K - Leveling Disc x 2

H - Washer x 4

C - Spine x 1

B -

in Screws x 10

J - TV Mounting Kit x 1

M - Cabinet Mount

Brackets x 2

N - Mount Riser x 1

O - 5/16 x 2-3/8” Screws x 3

L - Nut x 2

Measure

Here

bdiusa.com

customerservice@bdiusa.com

AREANA 9970

CABINET MOUNT

Step 3 A (for compatible Avion, Nora, Marina, Mirage, Novia, and Signal cabinets)

Attach two cabinet mount brackets M to rear-center edge of cabinet’s Top and Bottom Panels using

“ screws B and provided allen wrench A. Proceed to step 4.

B x 6

bdiusa.com

customerservice@bdiusa.com

AREANA 9970

CABINET MOUNT

Step 3 B (for compatible Corridor, Elements and other new cabinets)

Position mount riser N on the middle back edge of the cabinet’s bottom panel aligning with the 3 holes.

Position cabinet mount bracket M directly on top of it and secure with 5/16” x 2-3/8” screws O and

provided allen wrench A.

Attach one cabinet mount bracket M to rear-center edge of cabinet’s top panel using

“ screws B

and provided allen wrench A.

B x 3

O x 3

bdiusa.com

customerservice@bdiusa.com

AREANA 9970

CABINET MOUNT

Step 4

Attach spine C onto the 4 posts of the cabinet mount brackets M then fasten securely into place using four

(4)

in screws B and provided allen wrench A.

Note: If you are using the mount riser, tilt the spine C forward and hang the spine on the 2 upper posts. The

posts will enter the slots on the front of the spine C. Lift spine C slightly and start threading the upper screws

B into the upper posts then swing the bottom of spine C onto the 2 lower posts and thread screws B.

Tighten all 4 screws B with provided allen wrench A.

B x 4

1. start upper screws

2. start lower screws

3. tighten all 4 screws

lower posts

tilt column

forward 5

degrees to

start upper

screws

upper

posts

lower

posts

bdiusa.com

customerservice@bdiusa.com

AREANA 9970

CABINET MOUNT

Step 5

Attach each swiveling bracket assemby D to top of spine C with

x 1-

” screws E using allen

wrench A.

NOTE: There are several mounting-height positions to choose from on 3” increments. In general, for

larger TV’s (54” – 60”) select a higher set of mounting holes; on smaller TV’s (40”- 46”) select lower

set of mounting holes.

Side Mount

Front Mount

E x 4

NOTE: Selecting the ‘side-mount’ Spine location for the Swiveling Brackets will position television close to

rear of cabinet, but can limit left-to-right swiveling. Selecting the ‘front-mount’ Spine location will position

television approx 1.5” closer to cabinet front and will enable maximum left-to-right swiveling range.

Front Mount

Side Mount

bdiusa.com

customerservice@bdiusa.com

AREANA 9970

CABINET MOUNT

Step 6

Attach horizontal mounting bracket F to installed swiveling bracket assemblies D using

/8”

screws G and washers H with the provided allen wrench A.

NOTE: Slots along horizontal mounting bracket F must be at BOTTOM. Be sure to position each

swiveling bracket assembly D so that each sits within recessed portion of the Horizontal Mounting

Bracket F (Circled below).

Recommended

2-person step

for easy

installation

Front Mount

Side Mount

H x 4 G x 4

bdiusa.com

customerservice@bdiusa.com

AREANA 9970

CABINET MOUNT

Step 8

With the help of another person, lift television with installed vertical mounting

brackets I and lower carefully onto horizontal mounting bracket F.

Step 7

Position both vertical mounting brackets I on back of TV and

attach using mounting screws and spacers (if required) provided

in TV mounting kit J. Each bracket must align vertically with the

other and should be centered top to bottom.

Install leveling disc K onto threaded

posts of vertical mounting

bracket I. Make sure the felt

side is facing out.

NOTE: Various mounting screws

are provided in TV mounting kit J,

but some TVs may require specific

hardware not provided by BDI. In

such cases, please contact your TV

manufacturer to identify and source

your hardware.

K x 2

Recommended

2-person step

for safe

installation

bdiusa.com

customerservice@bdiusa.com

AREANA 9970

CABINET MOUNT

Step 8 (continue)

Level the TV using the leveling discs K near the slots in the lower horizontal mounting bracket F. Then

secure into place using provided nut L on exposed mounting stud until finger-tight.

Step 9

Use the open channel inside spine C to organize and route cabling to and from the TV.

BDI ARENA 9970 Assembly Instructions Manual

BDI ARENA 9970 Assembly Instructions Manual

BDI ARENA 9970 Assembly Instructions Manual

Related papers

Other documents