Advantech AIMB-227 AMD User manual

User Manual

AIMB-227

AMD Merlin Falcon Quad Core

Mini-ITX with DP/DVI-D/HDMI,

6COM, and Dual LAN

AIMB-227 User Manual ii

Copyright

The documentation and the software included with this product are copyrighted 2018

by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right

to make improvements in the products described in this manual at any time without

notice. No part of this manual may be reproduced, copied, translated or transmitted

in any form or by any means without the prior written permission of Advantech Co.,

Ltd. Information provided in this manual is intended to be accurate and reliable. How-

ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-

ments of the rights of third parties, which may result from its use.

Acknowledgements

AMI is a trademark of American Megatrends Inc.

IBM and PC are trademarks of International Business Machines Corporation.

AMD G-series is trademark of AMD Corporation

Nuvoton is a trademark of Nuvoton Technology.

All other product names or trademarks are properties of their respective owners.

Part No. 2006022710 Edition 1

February 2018

iii AIMB-227 User Manual

A Message to the Customer

Advantech Customer Services

Each and every Advantech product is built to the most exacting specifications to

ensure reliable performance in the harsh and demanding conditions typical of indus-

trial environments. Whether your new Advantech equipment is destined for the labo-

ratory or the factory floor, you can be assured that your product will provide the

reliability and ease of operation for which the name Advantech has come to be

known.

Your satisfaction is our primary concern. Here is a guide to Advantech’s customer

services. To ensure you get the full benefit of our services, please follow the instruc-

tions below carefully.

Technical Support

We want you to get the maximum performance from your products. So if you run into

technical difficulties, we are here to help. For the most frequently asked questions,

you can easily find answers in your product documentation. These answers are nor-

mally a lot more detailed than the ones we can give over the phone.

So please consult this manual first. If you still cannot find the answer, gather all the

information or questions that apply to your problem, and with the product close at

hand, call your dealer. Our dealers are well trained and ready to give you the support

you need to get the most from your Advantech products. In fact, most problems

reported are minor and are able to be easily solved over the phone.

In addition, free technical support is available from Advantech engineers every busi-

ness day. We are always ready to give advice on application requirements or specific

information on the installation and operation of any of our products.

AIMB-227 User Manual iv

Declaration of Conformity

FCC Class B

This device complies with the requirements in part 15 of the FCC rules:

Operation is subject to the following two conditions:

 This device may not cause harmful interference

 This device must accept any interference received, including interference that

may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B dig-

ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to pro-

vide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Opera-

tion of this device in a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at his/her own expense. The

user is advised that any equipment changes or modifications not expressly approved

by the party responsible for compliance would void the compliance to FCC regula-

tions and therefore, the user's authority to operate the equipment.

Caution! There is a danger of a new battery exploding if it is incorrectly installed.

Do not attempt to recharge, force open, or heat the battery. Replace the

battery only with the same or equivalent type recommended by the man-

ufacturer. Discard used batteries according to the manufacturer's

instructions.

v AIMB-227 User Manual

Memory Compatibility Test

Normal RAM test Data

ECC RAM test Data

Category Speed Capacity Vendor Module_PN Chip_PN

ADVAN-

TECH P/N

ECC Result Remark

DDR4 2133 4GB ATP

A4G04QA8

BLPBME

40A77 D9RGQ N/A N PASS

DDR4 2133 8GB

Advan-

tech

AQD-

SD4U8GN2

1-SG

SEC 552 BCPB

K4A4G085WD

AQD-

SD4U8GN

21-SG

NPASS

DDR4 2400 8GB ADATA

ADS240038

G17-BHYA

H5AN8G8NAF

R

AQD-

SD4U8GN

24-HE

NPASS

DDR4 2400 8GB

Advan-

tech

SQR-SD4N-

8G2K4HBC

H5AN8G8NAF

R UHC 643V

SQR-

SD4N-

8G2K4HB

C

NPASS

Category Speed Capacity Vendor Module_PN Chip_PN

ADVAN-

TECH P/N

ECC Result Remark

DDR4 2133 4GB ATP

A4F04QD8

BLPBME

40A77 D9RGQ N/A ECC PASS

DDR4 2133 8GB ATP

A4F08QG8

BLPBME

40A77 D9RGQ N/A ECC PASS

DDR4 2400 8GB ADATA

AD4B24003

8G17-BHYA

H5AN8G8NAF

R UHC 634A

AQD-

SD4U8GE

24-HE

ECC PASS

DDR4 2400 8GB Apacer

78.C2GF3.4

000B

SEC 649

K4A8G08 SWB

BCRC

N/A ECC PASS

AIMB-227 User Manual vi

Ordering Information

Product Warranty (2 years)

Advantech warrants to you, the original purchaser, that each of its products will be

free from defects in materials and workmanship for two years from the date of pur-

chase.

This warranty does not apply to any products which have been repaired or altered by

persons other than repair personnel authorized by Advantech, or which have been

subject to misuse, abuse, accident or improper installation. Advantech assumes no

liability under the terms of this warranty as a consequence of such events.

Because of Advantech’s high quality-control standards and rigorous testing, most of

our customers never need to use our repair service. If an Advantech product is defec-

tive, it will be repaired or replaced at no charge during the warranty period. For out-

of-warranty repairs, you will be billed according to the cost of replacement materials,

service time and freight. Please consult your dealer for more details.

If you think you have a defective product, follow these steps:

1. Collect all the information about the problem encountered. (For example, CPU

speed, Advantech products used, other hardware and software used, etc.) Note

anything abnormal and list any onscreen messages you get when the problem

occurs.

2. Call your dealer and describe the problem. Please have your manual, product,

and any helpful information readily available.

3. If your product is diagnosed as defective, obtain an RMA (return merchandise

authorization) number from your dealer. This allows us to process your return

more quickly.

4. Carefully pack the defective product, a fully-completed Repair and Replacement

Order Card and a photocopy proof of purchase date (such as your sales receipt)

Part Number CPU Display TPM PCIe GbE SATA COM

Thermal

Solution

AIMB-227MG2-00A1E RX-421BD DP/HDMI/DVI-D (1) x8 2 2 6 Active

AIMB-227MG2-01A1E RX-216GD DP/HDMI/DVI-D (1) x8 2 2 6 Passive

AIMB-227PG2-02A1E GX-224IJ DP/DVI-D (1) x4 2 2 6 Passive

vii AIMB-227 User Manual

in a shippable container. A product returned without proof of the purchase date

is not eligible for warranty service.

5. Write the RMA number visibly on the outside of the package and ship it prepaid

to your dealer.

Initial Inspection

Before you begin installing your motherboard, please make sure that the following

materials have been shipped:

 AIMB-227 AMD R-series mini-ITX motherboard

 1 x SATA HDD cable

 1 x SATA Power cable

 1 x Serial port cable(1 to 4)

 2 x Serial port cable(1 to 1)

 1 x I/O port bracket

 1 x Startup manual

 1 x Warranty card

 1 x CPU cooler

If any of these items are missing or damaged, contact your distributor or sales repre-

sentative immediately. We have carefully inspected the AIMB-227 mechanically and

electrically before shipment. It should be free of marks and scratches and in perfect

working order upon receipt. As you unpack the AIMB-227, check it for signs of ship-

ping damage. (For example, damaged box, scratches, dents, etc.) If it is damaged or

it fails to meet the specifications, notify our service department or your local sales

representative immediately. Also notify the carrier. Retain the shipping carton and

packing material for inspection by the carrier. After inspection, we will make arrange-

ments to repair or replace the unit.

AIMB-227 User Manual viii

ix AIMB-227 User Manual

Contents

Chapter 1 General Information ............................1

1.1 Introduction ............................................................................................... 2

1.2 Features .................................................................................................... 2

1.3 Specifications ............................................................................................ 2

1.3.1 Processor System......................................................................... 2

1.3.2 Expansion Slot .............................................................................. 2

1.3.3 Memory ......................................................................................... 2

1.3.4 Graphic Interface .......................................................................... 2

1.3.5 Ethernet Interface ......................................................................... 3

1.3.6 SATA Interface.............................................................................. 3

1.3.7 Rear I/O ........................................................................................ 3

1.3.8 Internal Connector ........................................................................ 3

1.3.9 Watchdog Timer............................................................................ 3

1.3.10 Power Requirement ...................................................................... 3

1.3.11 Environment.................................................................................. 3

1.3.12 Physical Characteristics................................................................ 3

1.4 Jumpers and Connectors .......................................................................... 4

Table 1.1: Connector / Header List.............................................. 4

Table 1.2: Jumper Setting List:.................................................... 5

1.5 Board layout: Jumper and Connector Locations ..................................... 10

Figure 1.1 Jumper and Connector Location .............................. 11

1.6 AIMB-227 Board Diagram ....................................................................... 12

Figure 1.2 AIMB-227 Board Diagram ........................................ 12

1.7 Safety Precautions .................................................................................. 12

1.8 Jumper Settings ...................................................................................... 13

1.8.1 How to Set Jumpers.................................................................... 13

1.8.2 CMOS Clear (JCMOS1).............................................................. 13

1.8.3 PSON1: ATX, AT Mode Selector ................................................ 13

1.9 System Memory ...................................................................................... 14

1.10 Memory Installation Procedures.............................................................. 14

Chapter 2 Connecting Peripherals ....................15

2.1 Introduction ............................................................................................. 16

2.2 ATX 12V/DCIN 12V Power Connector (ATX12V1/DCIN1) ..................... 16

2.3 Digital Visual Interface connector (DVI1) ................................................ 17

2.4 CMOS battery wafer box (BAT1) ............................................................ 18

2.5 COMS Mode selection (JCMOS1) .......................................................... 18

2.6 Embed DisplayPort (EDP1)..................................................................... 19

2.7 Low Voltage Differential Signaling (LVDS1)............................................ 19

2.8 DisplayPort (Up) + High Definition Multimedia Interface (Down) stack

connector (DP1+HDMI1)......................................................................... 20

2.9 VDD select for LVDS1 & EDP1 Panel (JLVDS1) .................................... 21

2.10 Inverter power connector (INV1) ............................................................. 21

2.11 USB3.0 stack connector (USB12)........................................................... 22

2.12 USB2.0 stack connector (USB34)........................................................... 23

2.13 USB Power selection header #1 (JUSBPWR1) ...................................... 24

2.14 USB Power selection header #2 (JUSBPWR2) ...................................... 24

2.15 LVDS VESA, JEIDA format selection pin header (JLVDS_VCON1)....... 25

2.16 Dual port USB2.0 header (USB78) ......................................................... 26

2.17 LAN LED (LANLED1).............................................................................. 27

2.18 Dual port RJ45 Connector (LAN12) ........................................................ 28

2.19 MINIPCIE with mSATA connector (MINIPCIE1) ..................................... 28

2.20 HD Audio Interfaces (LINE-OUT) (AUDIO1) ........................................... 29

AIMB-227 User Manual x

2.21 Front panel audio header (FPAUD1) ...................................................... 30

2.22 Audio amplifier output pin header (AMP1) .............................................. 31

2.23 HD Audio interface (SPDIF1).................................................................. 31

2.24 PCI-Express x8 slot (PCIEX8_1) ............................................................ 32

2.25 SATA DOM power selection pin header (JSATAPWR1) ........................ 33

2.26 Next Generation Form Factor KEY-E (NGFF_E_1); M.2 conn ............... 34

2.27 Serial ATA interface connector #2 and #1 (SATA2 and SATA1) ............ 35

2.28 Serial ATA Power connector #1 and #2 (SATA_PWR1 and SATA_PWR2)

36

2.29 SPI BIOS flash socket (SPI1) ................................................................. 37

2.30 COM1 and COM2 Box Header (COM1 and COM2) ............................... 38

2.31 COM3456 Box Header (COM3456)........................................................ 38

2.32 COM6 RI# selection pin header (JSETCOM6_V1)................................. 39

2.33 Keyboard & Mouse connector (KBMS1) ................................................. 40

2.34 8-bits General Purpose I/O Pin Header (GPIO1).................................... 41

2.35 CCTALK Voltage selection pin header (JCCT_VCON1) ........................ 42

2.36 Case Open selection pin header (JCASEOP_SW1)............................... 43

2.37 Case Open connector (JCASE1) ............................................................ 43

2.38 Low pin count interface connector (LPC1).............................................. 44

2.39 AMD DB-FP4 Merlin Falcon SoC (CPU1)............................................... 45

2.40 DDR4 SO-DIMM Socket CH-A (DIMMA1) .............................................. 45

2.41 DDR4 SO-DIMM Socket CH-B (DIMMB1) .............................................. 45

2.42 5VSB input connector (ATX_5VSB1)...................................................... 46

2.43 AT/ATX Mode selection (PSON1)........................................................... 47

2.44 Watch Dog timer output and OBS beep (JWDT1+JOBS1)..................... 48

2.45 Power LED and keyboard lock pin header (JFP2).................................. 49

2.46 PWRBTN#/ RESET#/HDD LED/ Serial bus from HW monitor IC/Internal

Buzzer /External Speaker header (JFP1) ............................................... 50

2.46.1 ATX soft power switch (JFP1/PWR_BTN).................................. 51

2.46.2 Reset (JFP1/RST_BTN) ............................................................. 51

2.46.3 HDD LED (JFP1/HDD_LED) ...................................................... 51

2.46.4 External speaker (JFP1/SPEAKER) ........................................... 51

2.47 System Fan #1 connector (SYSFAN1) ................................................... 51

2.48 CPU FAN #1 connector (CPUFAN1) ...................................................... 52

2.49 SIM Card holder (SIM1) .......................................................................... 53

Chapter 3 BIOS Operation.................................55

3.1 Introduction ............................................................................................. 56

3.2 BIOS Setup ............................................................................................. 56

3.2.1 Main Menu .................................................................................. 57

3.2.2 Advanced BIOS Features ........................................................... 58

3.2.3 Chipset........................................................................................ 70

3.2.4 Boot ............................................................................................ 74

3.2.5 Security....................................................................................... 75

3.2.6 Save & Exit ................................................................................. 76

Chapter 4 Software Introduction & Service .....77

4.1 Introduction ............................................................................................. 78

4.2 Value-Added Software Services ............................................................. 78

4.2.1 Software API............................................................................... 78

4.2.2 Software Utility............................................................................ 80

Chapter 5 Chipset Software Installation Utility 81

5.1 Before You Begin.................................................................................... 82

5.2 Introduction ............................................................................................. 82

xi AIMB-227 User Manual

5.3 Windows 10/7 Driver Setup..................................................................... 82

Chapter 6 Graphics Setup..................................83

6.1 Introduction ............................................................................................. 84

6.2 Windows 10/7.......................................................................................... 84

Chapter 7 LAN Configuration.............................85

7.1 Introduction ............................................................................................. 86

7.2 Features .................................................................................................. 86

7.3 Installation ............................................................................................... 86

7.4 Windows 10/7 Driver Setup..................................................................... 87

Appendix A Programming the Watchdog Timer..89

A.1 Programming the Watchdog Timer ......................................................... 90

A.1.1 Watchdog Timer Overview.......................................................... 90

A.1.2 Programming the Watchdog Timer ............................................. 90

Table A.1: Watchdog Timer Registers ....................................... 92

A.1.3 Example Program ....................................................................... 93

Appendix B I/O Pin Assignments..........................97

B.1 Digital Visual Interface connector (DVI1) ................................................ 98

B.2 Embed DisplayPort (EDP1)..................................................................... 98

B.3 Low Voltage Differential Signaling (LVDS1)............................................ 99

B.4 DisplayPort (Up) + High Definition Multimedia Interface (Down) stack

connector (DP1+HDMI1)....................................................................... 100

B.5 USB3.0 stack connector (USB12)......................................................... 101

B.6 USB2.0 stack connector (USB34)......................................................... 101

B.7 Dual port RJ45 Connector (LAN12) ...................................................... 102

B.8 MINIPCIE with mSATA connector (MINIPCIE1) ................................... 102

B.9 PCI-Express x8 slot (PCIEX8_1) .......................................................... 104

B.10 Next Generation Form Factor KEY-E (NGFF_E_1) ; M.2 conn ............ 105

B.11 COM2 Box Header (Colay CCTalk)

COM2.................................................................................................... 106

B.12 COM3456 Box Header (COM3456)

COM3 (BIOS selectable RS232/422/485, Default RS-232) .................. 107

AIMB-227 User Manual xii

Chapter 1

1 General Information

AIMB-227 User Manual 2

1.1 Introduction

AIMB-227 is a Mini-ITX motherboard based on Merlin Falcon” RX-421BD processor

can deliver up to up to 22% more graphics performance than the previous enervation

RX-427BB based on the 3DMark 11 (Performance) benchmark (good graphics per-

formance), designed with rich I/O functions and dual display support, AIMB-227 is

ideal for any rugged applications such as Digital Surveillance, Digital Signage, Thin

Client, Electronic Gaming Machines, etc. With the pre-loaded remote management

software - SUSIAccess, AIMB-227 not only saves development cost but also

enhances system management efficiency.

1.2 Features

 Rich I/O connectivity: 6 serial ports, 4 USB 2.0, 4 USB3.0, 2 SATA III, Dual

GbE LAN

 Standard Mini-ITX form factor: The AIMB-227 is a Mini-ITX motherboard

 Wide selection of storage devices: SATA HDD, SATA DOM, mSATA custom-

ers benefit from the flexibility of using the most suitable storage device for larger

capacity

 Optimized integrated graphic solution: With AMD Radeon 3rd Generation

GCN (Up to 8 CUs) Graphics, Support DirectX® 12 and UVD v6 Unified Video

Decode Engine

1.3 Specifications

1.3.1 Processor System

 CPU: AMD R-series, supports Quad/Dual core CPU

 Max. Speed: Quad Core 2.1 GHz (RX-421BD, TDP 35 W)/ Dual Core 1.6 GHz

(RX-216GD, TDP 15W) Dual Core 2.4GHz (GX-224IJ, TDP 15W)

 L2 Cache: 2 MB

 BIOS: AMI 16 Mbit SPI

1.3.2 Expansion Slot

 Mini-PCIe: One, full size

 M.2 E Key: 1, (2230)

 PCIe x8: 1

1.3.3 Memory

 Technology: Dual channel DDR4 2133 MHz

 Max. Capacity: 16 GB

 Socket: 2 x 260 pin SODIMM

1.3.4 Graphic Interface

 Controller: AMD Radeon 3rd Generation GCN (Up to 8 CUs)

 HDMI: 1, 4096 x 2160 @ 60Hz Max (60Hz requires re-timer)

 LVDS: 1, supports dual channel 48-bit up to 1920 x colay DP 1.2 port (Optional)

 DP 1.2: 1, supports DP++, resolution up to 4096 x 2160 @ 60Hz

 DVI-D: 1, supports up to SXGA 1920 x 1200

 Multiple Display: 3 independent display by DP/HDMI/DVI-D

3 AIMB-227 User Manual

Chapter 1 General Information

1.3.5 Ethernet Interface

 Interface: 10/100/1000 Mbps

 Controller: GbE: Realtek RTL8111G

 Connector: RJ-45 x 2

1.3.6 SATA Interface

 Max Data Transfer Rate: 600 MB/s

 Channel: 2

1.3.7 Rear I/O

 DVI-D: 1

 HDMI: 1

 DP: 1

 Ethernet: 2

 USB: 4 (2USB2.0 & 2USB3.0)

 Audio: 1 (Line out)

 DC jack: 1

1.3.8 Internal Connector

 LVDS & Inverter: 1

 USB: 4 (2USB2.0 & 2USB3.0)

 Serial: 6 (5 x RS232,1 x RS232/422/485; COM 3 support RS232/422/485 auto

flow control; COM6 support 5v/12V by jumper selection; 1 COM support CCtalk;

1 COM support TTL)

 SATA: 2

 SATA Power Connector: 2

 GPIO: 8-bit

 Mini PCIE slot: 1 miniPCIE slot, F/S support mSATA; F/S support SIM holder

 M.2 E Key: 1, (2230)

1.3.9 Watchdog Timer

 Output: System reset

 Interval: Programmable 1 ~ 255 sec/min

1.3.10 Power Requirement

 Typical:

– Single Voltage 12V DC input by 1x 2.5φ connector or 1x internal 2x2-pin

power

– AT/ATX Supported by Jumper

– Max power consumption: 60.83 W (16G DDR4 RAM)

1.3.11 Environment

 Temperature:

– 0 ~ 60° C (32 ~ 140° F), Operating

– -40 ~ 85° C (-40 ~ 185° F), Non-operating

1.3.12 Physical Characteristics

 Dimensions: 170 mm x 170 mm (6.69" x 6.69")

AIMB-227 User Manual 4

1.4 Jumpers and Connectors

Connectors on the AIMB-227 motherboard link it to external devices such as hard

disk drives and a keyboard. In addition, the board has a number of jumpers used to

configure your system for your application.

The tables below list the function of each of the board jumpers and connectors. Later

sections in this chapter give instructions on setting jumpers. Chapter 2 gives instruc-

tions for connecting external devices to your motherboard.

Table 1.1: Connector / Header List

Description Part Reference

1 DC input Jack DCIN1

2 Digital Visual Interface connector DVI1

3 Coin Battery wafer box BAT1

4 COMS Mode selection JCMOS1

5 Embed DisplayPort EDP1

6

DisplayPort (Up) + High Definition Multimedia Interface

(Down) stack connector

DP1+HDMI1

7 VDD select for LVDS1 & EDP1 Panel JLVDS1

8 Low Voltage Differential Signaling LVDS1

9 USB3.0 stack connector USB12

10 Inverter power connector INV1

11 USB2.0 stack connector USB34

12 USB Power selection for USB12 & USB34 JUSBPWR1

13 USB Power selection for USB56 & USB78 JUSBPWR2

14 LVDS VESA, JEIDA format selection pin header JLVDS_VCON1

15 Dual port USB2.0 header USB78

16 LAN LED LANLED1

17 Dual port RJ45 Connector LAN12

18 MINIPCIE with mSATA connector MINIPCIE1

19 HD Audio Interface (LINE-OUT) AUDIO1

20 Front panel audio header FPAUD1

21 Audio amplifier output pin header AMP1

22 HD Audio interface (Digital) SPDIF1

23 PCI Express x8 slot PCIEX8_1

24 SATA DOM power selection pin header JSATAPWR1

25 Next Generation Form Factor KEY-E NGFF_E_1

26 Serial ATA interface connector #2 SATA2

27 Serial ATA interface connector #1 SATA1

28 Serial ATA Power connector #1 SATA_PWR1

29 Serial ATA Power connector #2 SATA_PWR2

30 SPI BIOS Flash Socket SPI1

31 COM1 Box Header COM1

32 COM2 Box Header COM2

33 COM6 RI# selection pin header JSETCOM6_V1

34 PS2 Keyboard & Mouse connector KBMS1

35 8-bits General Purpose I/O Pin Header GPIO1

36 CCTALK Voltage selection pin header JCCT_VCON1

37 Case Open selection pin header JCASEOP_SW1

5 AIMB-227 User Manual

Chapter 1 General Information

1. USB VBUS selection for USB12 & USB34 (JUSBPWR1)

38 Case Open connector JCASE1

39 COM3 ~ COM6 Box Header COM3456

40 Low pin count interface connector LPC1

41 AMD DB-FP4 Merlin Falcon SoC CPU1

42 DDR4 SO-DIMM Socket CH-A DIMMA1

43 DDR4 SO-DIMM Socket CH-B DIMMB1

44 5VSB input connector ATX_5VSB1

45 AT/ATX Mode selection PSON1

46 Watch Dog timer output and OBS beep JWDT1+JOBS1

47 Power LED and keyboard lock pin header JFP2

48

PWRBTN#/ RESET#/HDD LED/ Serial bus from HW

monitor IC/Internal Buzzer / External Speaker header

JFP1

49 System Fan #1 connector SYSFAN1

50 CPU FAN #1 connector CPUFAN1

51 Dual port USB3.0 header USB56

52 ATX 12V power supply connector ATX12V1

53 SIM Card holder SIM1

Table 1.2: Jumper Setting List:

Description Part Reference

1 USB VBUS Selection for USB12 & USB34 JUSBPWR1

2 USB VBUS Selection for USB56 & USB78 JUSBPWR2

3 VDD select for LVDS1 & EDP1 Panel JLVDS1

4 SATA DOM power selection pin header JSATAPWR1

5 CMOS clear JCOMS1

6 COM6_RI# Pin Selection JSETCOM6_V1

7 CCTALK selection pin header JCCT_VCON1

8 Case open selection JCASEOP_SW1

9 AT / ATX Mode selection PSON1

10

PWRBTN# / RESET# / HDD LED / Serial bus / Internal

Buzzer / External Speaker header

JFP1

11 Watch Dog Timer output and OBS Beep JWDT1+JOBS1

Function Setting

Set USB VBUS as +5VSB (Default)

Set USB VBUS as +5V

Table 1.1: Connector / Header List

1 2 3

AIMB-227 User Manual 6

2. USB VBUS Selection for USB56 & USB78 (JUSBPWR2)

3. VDD select for LVDS1 & EDP1 Panel (JLVDS1)

4. SATA DOM power selection pin header (JSATAPWR1)

Function Setting

Set USB VBUS as +5VSB (Default)

Set USB VBUS as +5V

Function Setting

Jumper position for +3.3V (Default)

Jumper position for +5V

Jumper position for +12V

Function Setting

SATA1 Such as SATA CONN. (Default)

SATA1 Support SATA DOM Power

1 2 3

7 AIMB-227 User Manual

Chapter 1 General Information

5. CMOS clear (JCOMS1)

6. PWRBTN# / RESET# / HDD LED / Serial bus / Internal Buzzer / External

Speaker header (JFP1)

7. COM6_RI# Pin Selection (JSETCOM6_V1)

Function Setting

Normal (Default)

Clear CMOS

Function Setting

Internal Buzzer (Default)

Function Setting

Jumper position for RI# (Default)

Jumper position for +5V

Jumper position for +12V

1 2 3

AIMB-227 User Manual 8

8. CCTALK selection pin header (JCCT_VCON1)

9. Case open selection (JCASEOP_SW1)

10. AT / ATX Mode selection (PSON1)

11. Watchdog timer output and OBS beep (JWDT1+JOBS1)

Function Setting

CCTALK 12V (Default)

CCTALK 5V

Function Setting

Normal Close

Normal Open (Default)

Function Setting

Normal Close

Normal Open (Default)

1 2 3

Page is loading ...

Advantech AIMB-227 AMD User manual

Advantech AIMB-227 AMD User manual

Related papers

Other documents