alpro EB1001 User manual

Brand: alpro

Model: EB1001

Type: User manual

alpro EB1001 is an electric bolt designed for use in weather-protected areas. It has a stainless steel bolt with a diameter of 15mm and a throw of 15mm. The voltage required is 12vDC and the activating current is 1.0A. The holding current is 250 mA. The alpro EB1001 is fully protected against transients and reverse polarity. It has an autolock time delay that can be set for 0, 3, 6, or 9 seconds. The alpro EB1001 also has a door position switch (DSS) and a bolt position indicator. The bolt face plate is 203 x 34 x 3mm and the strike plate is 98 x 34 x 3mm.

alpro EB1001 is an electric bolt designed for use in weather-protected areas. It has a stainless steel bolt with a diameter of 15mm and a throw of 15mm. The voltage required is 12vDC and the activating current is 1.0A. The holding current is 250 mA. The alpro EB1001 is fully protected against transients and reverse polarity. It has an autolock time delay that can be set for 0, 3, 6, or 9 seconds. The alpro EB1001 also has a door position switch (DSS) and a bolt position indicator. The bolt face plate is 203 x 34 x 3mm and the strike plate is 98 x 34 x 3mm.

Electric Bolt

EB1001

Read all instructions before starting installation

Ensure you have the following:-

- Strike plate

- Electric bolt

All rebate strips and/or frame stops

should be fitted before starting.

A 2 amp Power Supply should be

provided to ensure there is a Full 1

amp for the bolt. This should allow

for a basic Access System and a

back up battery to be connected

to the same source.

WARNING - THE CONNECTION OF

AN INCORRECT VOLTAGE MAY

RESULT IN DAMAGE NOT COVERED

BY THE PRODUCT WARRANTY.

PACK CONTENTS

Technical Information

General Installation Instructions

Power to Lock/Fail open.

Stainless steel bolt - diameter 15mm

- throw 15mm

Voltage required - 12vDC

Activating current - 1.0A

Holding current - 250 mA

Fully protected against transients and

reverse polarity

The Autolock Time Delay can be set for 0,

3, 6 or 9 seconds.

Monitoring - Door position switch (DSS)

- Bolt position indicator

Bolt Face Plate 203 x 34 x 3mm

Strike Plate 98 x 34 x 3mm

15

126.5

203

57.5

9.5

40

14

172

3

AUTOLOCK TIME DELAY SETTING

0 SEC

3 SEC

6 SEC

9 SEC

1 2

ON

OFF

1 2

ON

OFF

1 2

ON

OFF

1 2

ON

OFF

17

9.5

1

2

3

x8

x4

Read all instructions before starting installation

Electric Bolt

EB1001

[email protected] www.alpro.co.uk

01202 676262

01202 680101

Registered in England & Wales 1925537 © July 2017 IEC. All rights reserved. All dimensions are nominal and subject to tolerances

GENERAL INSTALLATION INSTRUCTIONS

The selection of

appropriate power supply

cable is very important to

ensure lock receives

sufficient power to

operate.

Connect flying leads (+)

Red (-) Black. Note - other

leads for connection of

LED via plug in lead *NOT

FOR POWER INPUT*.

This product has been

designed for use in

weather protected

areas and under normal

circumstances does not

require any

maintenance. DO NOT

OIL OR LUBRICATE.

This product must be

used in conjuction with a

quality floor spring or

door closer to ensure

positive realignment on

closing.

Door Status Sensor

White Normally Open

White Common

Rated 0.5A

12vDC

LED

BLACK (-) Negative

RED (+) Positive

79

15.5

98.4

15.5

30.4

15.2

M5 x 0.8 x 2

ø5.1 x 2

C Of Door

17.2

34.4

184

203.4

15.5

10

10

15.5

50 REF

M5 x 0.8 x 2

ø8 LED

C Of Door

ø5.1 x 2

4

5

6

7

1
2

alpro EB1001 User manual

Brand: alpro

Model: EB1001

Type: User manual

alpro EB1001 is an electric bolt designed for use in weather-protected areas. It has a stainless steel bolt with a diameter of 15mm and a throw of 15mm. The voltage required is 12vDC and the activating current is 1.0A. The holding current is 250 mA. The alpro EB1001 is fully protected against transients and reverse polarity. It has an autolock time delay that can be set for 0, 3, 6, or 9 seconds. The alpro EB1001 also has a door position switch (DSS) and a bolt position indicator. The bolt face plate is 203 x 34 x 3mm and the strike plate is 98 x 34 x 3mm.

Related papers

Other documents