alpro EB1001 User manual

Brand
alpro
Model
EB1001
Type
User manual

alpro EB1001 is an electric bolt designed for use in weather-protected areas. It has a stainless steel bolt with a diameter of 15mm and a throw of 15mm. The voltage required is 12vDC and the activating current is 1.0A. The holding current is 250 mA. The alpro EB1001 is fully protected against transients and reverse polarity. It has an autolock time delay that can be set for 0, 3, 6, or 9 seconds. The alpro EB1001 also has a door position switch (DSS) and a bolt position indicator. The bolt face plate is 203 x 34 x 3mm and the strike plate is 98 x 34 x 3mm.

alpro EB1001 is an electric bolt designed for use in weather-protected areas. It has a stainless steel bolt with a diameter of 15mm and a throw of 15mm. The voltage required is 12vDC and the activating current is 1.0A. The holding current is 250 mA. The alpro EB1001 is fully protected against transients and reverse polarity. It has an autolock time delay that can be set for 0, 3, 6, or 9 seconds. The alpro EB1001 also has a door position switch (DSS) and a bolt position indicator. The bolt face plate is 203 x 34 x 3mm and the strike plate is 98 x 34 x 3mm.

Electric Bolt
EB1001
Read all instructions before starting installation
Ensure you have the following:-
- Strike plate
- Electric bolt
All rebate strips and/or frame stops
should be fitted before starting.
A 2 amp Power Supply should be
provided to ensure there is a Full 1
amp for the bolt. This should allow
for a basic Access System and a
back up battery to be connected
to the same source.
WARNING - THE CONNECTION OF
AN INCORRECT VOLTAGE MAY
RESULT IN DAMAGE NOT COVERED
BY THE PRODUCT WARRANTY.
PACK CONTENTS
Technical Information
General Installation Instructions
Power to Lock/Fail open.
Stainless steel bolt - diameter 15mm
- throw 15mm
Voltage required - 12vDC
Activating current - 1.0A
Holding current - 250 mA
Fully protected against transients and
reverse polarity
The Autolock Time Delay can be set for 0,
3, 6 or 9 seconds.
Monitoring - Door position switch (DSS)
- Bolt position indicator
Bolt Face Plate 203 x 34 x 3mm
Strike Plate 98 x 34 x 3mm
15
126.5
203
57.5
9.5
40
14
172
3
AUTOLOCK TIME DELAY SETTING
0 SEC
3 SEC
6 SEC
9 SEC
1 2
ON
OFF
1 2
ON
OFF
1 2
ON
OFF
1 2
ON
OFF
17
9.5
1
2
3
x8
x4
Read all instructions before starting installation
Electric Bolt
EB1001
[email protected] www.alpro.co.uk
01202 676262
01202 680101
Registered in England & Wales 1925537 © July 2017 IEC. All rights reserved. All dimensions are nominal and subject to tolerances
GENERAL INSTALLATION INSTRUCTIONS
The selection of
appropriate power supply
cable is very important to
ensure lock receives
sufficient power to
operate.
Connect flying leads (+)
Red (-) Black. Note - other
leads for connection of
LED via plug in lead *NOT
FOR POWER INPUT*.
This product has been
designed for use in
weather protected
areas and under normal
circumstances does not
require any
maintenance. DO NOT
OIL OR LUBRICATE.
This product must be
used in conjuction with a
quality floor spring or
door closer to ensure
positive realignment on
closing.
Door Status Sensor
White Normally Open
White Common
Rated 0.5A
12vDC
LED
BLACK (-) Negative
RED (+) Positive
79
15.5
98.4
15.5
30.4
15.2
M5 x 0.8 x 2
ø5.1 x 2
C Of Door
17.2
34.4
184
203.4
15.5
10
10
15.5
50 REF
M5 x 0.8 x 2
ø8 LED
C Of Door
ø5.1 x 2
4
5
6
7
  • Page 1 1
  • Page 2 2

alpro EB1001 User manual

Brand
alpro
Model
EB1001
Type
User manual

alpro EB1001 is an electric bolt designed for use in weather-protected areas. It has a stainless steel bolt with a diameter of 15mm and a throw of 15mm. The voltage required is 12vDC and the activating current is 1.0A. The holding current is 250 mA. The alpro EB1001 is fully protected against transients and reverse polarity. It has an autolock time delay that can be set for 0, 3, 6, or 9 seconds. The alpro EB1001 also has a door position switch (DSS) and a bolt position indicator. The bolt face plate is 203 x 34 x 3mm and the strike plate is 98 x 34 x 3mm.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents