2. KitchenAid
  3. KRWS 9010/1
KRWS 9010/1

KitchenAid KRWS 9010/1 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the KitchenAid KRWS 9010/1 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the minimum area required for air passage in the base board?
    Can the wine drawer be installed in a column?
    Can the wine drawer be installed on its own or in a single cabinet?
    What are the dimensions of the wine drawer?
    How many technicians are required for installation and maintenance?
    What is the minimum clearance required around the wine drawer?
    How many screws are used to fix the wine drawer to the cabinet?
Assembly instructions
Installation kit supplied 4
Wine drawer overall dimension 5
Installation kit 6
Preparation of the cabinet for inserting the wine drawer 8
Fitting the two brackets supplied in the installation kit 9, 10
Inserting the wine drawer in the cabinet 13
Inserting the corrugated plastic sheet covering 16
Installation completed 17
The wine drawer is designed for built-in installation and must not be used as a free-standing unit.
Installation and maintenance must be carried out by at least two qualified technicians.
INSTALL THE WINE DRAWER ONLY IN POSITION UNDER THE KITCHEN WORKTOP.
Make sure the wine drawer is fixed to the adjacent cabinet with the brackets supplied.
DO NOT INSTALL THE WINE DRAWER IN A COLUMN.
DO NOT INSTALL THE WINE DRAWER ON ITS OWN OR IN A SINGLE CABINET.
Otherwise the wine drawer will be unstable, with risk of tipping over and consequent injury or damage.
Do not start this electrical appliance if it is damaged, does not work properly, is partially disassembled or if
there are broken or missing components, including damaged cable or power socket.
Make sure the power cable is in a position where it cannot be trodden on, tripped over, damaged or
undergo strain.
Do not install or store the appliance in places where it can be exposed to bad weather or temperatures
below freezing.
The min. area in the base board for the passage of air must be at least 200 cm2.
Installation kit supplied
4
5
Wine drawer overall dimension
6
SCALE 1:1
N° 2 BRACKET
SCALE 1:5
SCALE 1:2
SCALE 1:2
SCALE 1:5
SCALE 1:1
N° 1 COVERING IN CORRUGATED PLASTIC SHEE
T
N° 2 SIDE ADHESIVE
N°1 TEMPLATE
N° 6 SCREW 4.2x13 UNI 6954-71 B
N° 14 SCREW 4.8x15 UNI 6955-71 AB
Installation kit
7
8
VERT.
VERT.
16 MIN.
CHAMFER 014x3.6
16 MIN.
50 MIN.
550 MIN.
VERT.-VERT. SECTION
SECTION F-F
SCALE 1:1
680 MIN.
316 MIN.
100
100
100 100
F
F
81.5
Preparation of the cabinet for inserting the wine drawer
Fitting the two brackets supplied in the installation kit
9
316 MIN.
340 MAX.
60
VERT.-VERT SECTION
VERT.
VERT.
10
BRACKET
N° 10 SELF-TAPPING SCREWS 4.8x 15 UNI 6955-71B
Fitting the two brackets supplied in the installation kit
11
N° 2 SIDE ADHESIVE
SCALE 29:200
SCALE 29:200
12
VERT.
VERT.-VERT. SECTION
SEE DETAIL X
VERT.
SEE DETAIL Y
DETAIL X
SCALE 1:1
354 MIN.
DETAIL Y
SCALE 1:1
897
897
Inserting the wine drawer in the cabinet
13
N° 6 SCREWS UNI 6954-7IB 4.2x13
MIN. 200 Cm
2
14
SEE DETAIL X
DETAIL X
SCALE 1:2
TEMPLATE
1. INSERT THE WINE DRAWER IN THE CABINET
POSITIONING IT SO THAT THE DRAWER SEAL EDGE IS 44 mm. FROM THE FRONT SIDE OF THE CABINET USING THE SPECIAL TEMPLATE SUPPLIED.
2. THEN FIX THE WINE DRAWER TO THE CABINET WITH THE SCREWS SUPPLIED.
15
CUT AND BEND
SCALE 33:200
SCALE 33:200
REPARATION OF THE CORRUGATED PLASTIC SHEET
COVERING SUPPLIED IN THE INSTALLATION KIT
B1
B2
B3
B4
AB
704
716
717
720
722
728
850
1
2
2
2
2
3
4
4 SCREWS 4.8x 15 UNI 6955-71 AB
Inserting the corrugated plastic sheet covering
16
17
Installation completed
5019 102 00572
Printed in Italy
n
05/10
GB
/