Hampton Bay HB3431-240 Installation guide

INSTRUCTIONS MANUAL

HOME DEPOT SKU# 392-985(UPC# 046335942028)

Page 1

INTERIOR FIVE LIGHT CHANDELIER

Page 2

Thank you for purchasing this Hampton Bay Interior Five Light

Chandelier. This product has been manufactured with the highest

standards of safety and quality.

1. Easy to install

2. Handsome Tuscan Copper Finish, decorated with Crystal Leaves.

FEATURES:

Before returning to your local Home Depot, please call our Customer

Service Team at 1-877-527-0313 or visit www.homedepot.com. Please

reference your SKU (392-985) or UPC (046335942028).

QUESTIONS, PROBLEMS, MISSING PARTS:

Page 3

TOOLS REQUIRED FOR INSTALLATION AND ASSEMBLY

(not included):

CAUTION:

1. Before starting installation of this fixture or removal of a previous

fixture, disconnect the power by turning off the circuit breaker or by

removing the fuse at the fuse box.

2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY

ELECTRICAL QUESTIONS. If you have any non-electrical

questions about this fixture, please call our Customer Service Team at

1-877-527-0313 or visit www.homedepot.com. Please reference your

SKU (392-985) or UPC (046335942028).

3. KEEP your receipt and these Instructions for Proof of Purchase.

Safety

goggles

Wire

strippers

Phillips

screwdriver

Electrical

tape

Wire

cutters

Flathead

screwdriver

3 Candelabra

Light Bulbs (60

watt maximum)

PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):

ASSEMBLY INSTRUCTIONS:

1. Carefully unpack the fixture. Lay out all parts on a clean surface.

2. Thread the Top Loop (#3) onto the top of the Main Fixture Body (#1). (Fig. 1)

3. Attach the Chain (#5) to the Top Loop (#3) using the Chain Link Connector

(#4). (Fig. 2)

4. Raise the Chain (#5) and the Main Fixture Body (#1) up to the Outlet Box (#9)

to determine the desired length needed for installation. Identify the chain link

that needs to be opened to remove the excess chain. Using two pair of pliers,

open the chain link. Remove and discard the excess chain. Keep the Opened

Chain Link (#6). (Fig. 3)

Page 4

1 ea Main Fixture

Body (#1)

1 ea Chain (6 ft) (#5)

1 ea Chain Link

Connector (#4)

5. Unravel the Cord (#7) and the Fixture Ground Wire (#8). Starting at the Top

Loop (#3), thread the Cord (#7) and the Fixture Ground Wire (#8) through

every other link of the Chain (#5). (Fig. 3)

6. Proceed to the Installation Instructions.

7. Install five incandescent candelabra Light Bulbs (#2) into the sockets of the

Main Fixture Body (#1). Do not exceed a 60 watts for each light bulb. (Fig. 4)

ASSEMBLY INSTRUCTIONS (CONT.):

Page 5

ASSEMBLY:

3. Top

Loop

Page 6

Fig. 1

Fig. 2

3. Top Loop

5. Chain

4. Chain Link

Connector

CHAIN

LINK CONNECTOR

Opened

Closed

1. Main

Fixture Body

ASSEMBLY (CONT.):

Page 7

5. Chain

6. Opened

Chain Link

7. Cord

8. Fixture

Ground Wire

Fig. 3

Fig. 4

2. Light

Bulb

1. Main

Fixture Body

1 ea Threaded Ring (#16)

1 ea Canopy (#15)

INSTALLATION INSTRUCTIONS:

PARTS INCLUDED FOR INSTALLATION (parts are not to

scale):

1 ea Mounting Bracket (#10)

2 ea Mounting Screws

(#11)

2 ea Hex Nuts (#12)

3 ea Wire Nuts

(#18)

Page 8

1 ea Nipple (#13)

1 ea Screw Collar Loop (#14)

1. Thread the two Hex Nuts (#12) onto the Nipple (#13) to its approximate

midpoint. Thread the Nipple (#13) in through the center hole of the Mounting

Bracket (#10) approximately 1/3 of the way. Do not tighten the Hex Nuts

(#12). (Fig. 5)

2. Pull the Supply Wires and the Supply Ground Wire (#17) out from the Outlet

Box (#9). Attach the Mounting Bracket (#10) to the Outlet Box (#9) by

feeding the Mounting Screws (#11) through the slots of the Mounting Bracket

(#10) and tightening them into the mounting holes of the Outlet Box (#9).

(Fig. 5)

3. Thread the Screw Collar Loop (#14) 8 to 9 turns onto the bottom end of the

Nipple (#13). Tighten the bottom Hex Nut (#12) against Screw Collar Loop

(#14). (Fig. 5)

INSTALLATION INSTRUCTIONS (CONT.):

4. Place the Canopy (#15) over the Outlet Box (#9) and check if the midpoint of

the outer threads of the Screw Collar Loop (#14) aligns with the bottom

surface of the Canopy (#15). If not, turn the Screw Collar Loop (#14) until its

midpoint aligns with the Canopy (#15). (Fig. 6)

5. Remove the Canopy (#15) and tighten the top Hex Nut (#12) against the

Mounting Bracket (#10). (Fig. 5)

6. Slide the Threaded Ring (#16) onto the Chain (#5), followed by the Canopy

(#15). (Fig. 7)

7. Hook the previously Opened Chain Link (#6) onto the top link of the Chain

(#5). Raise the Opened Chain Link (#6) along with the Chain (#5) and the

Main Fixture Body (#1) up to the ceiling and hook it onto the Screw Collar

Loop (#14). Using pliers, close the Opened Chain Link (#6). (Fig. 8)

8. Feed the Cord (#7) and Fixture Ground Wire (#8) into the Center Hole (#19)

of the Screw Collar Loop (#14), into the Nipple (#13) and out to its other end,

then out of the Outlet Box (#9). Continue feeding the Cord (#7) and Fixture

Ground Wire (#8), until there is no slack remaining. (Fig. 9 & 10)

9. Cut off any excess Cord (#7) and Fixture Ground Wire (#8), leaving

approximately 6” extending from the Outlet Box (#9). Split apart the Cord

(#7), separating the Ribbed Wire (#22) and the Smooth Wire (#23). Strip off

3/8” of insulation from each wire. Loop the Fixture Ground Wire (#8) around

the Ground Screw (#20), leaving approximately 4” of wire extending from the

Ground Screw (#20). Tighten the Ground Screw (#20) against the Mounting

Bracket (#10). Make the following wire connections:

White (Neutral) Supply Wire (#21) to Ribbed Fixture Wire (#22)

Black (Hot) Supply Wire (#24) to Smooth Fixture Wire (#23)

Supply Ground Wire (#17) to Fixture Ground Wire (#8)

Wrap each wire connection with 2” of electrical tape. Carefully tuck all wire

connections into the Outlet Box (#9). (Fig. 11)

Page 9

10. Slide the Canopy (#15) up the Chain (#5), toward the Outlet Box (#9), and

up against the ceiling surface. Slide the Threaded Ring (#16) up the Chain

(#5) and thread it onto the Screw Collar Loop (#14) to secure the Canopy

(#15) flush against the ceiling surface. (Fig. 12)

11. Proceed to Step 7 of the Assembly Instructions.

12. Installation is complete. Turn on power at the circuit breaker or fuse box.

Turn the light switch on to activate the fixture.

INSTALLATION INSTRUCTIONS (CONT.):

Page 10

INSTALLATION:

10. Mounting

Bracket

11. Mounting

Screws

12. Hex Nut

13. Nipple

14. Screw Collar Loop

Page 11

9. Outlet

Box

5. Chain

3. Top Loop

16. Threaded

Ring

15. Canopy

9. Outlet Box

15. Canopy

14. Screw

Collar Loop

Fig. 5

Fig. 6

Fig. 7

INSTALLATION (CONT.):

9. Outlet

Box

14. Screw

Collar Loop

6. Opened

Chain Link

5. Chain

16. Threaded Ring

15. Canopy

3. Top Loop

14. Screw

Collar Loop

7. Cord

8. Fixture

Ground

Wire

7. Cord

8. Fixture

Ground

Wire

Fig. 8

Fig. 9

Fig. 10

Page 12

7. Cord

8. Fixture

Ground Wire

19. Center

Hole

INSTALLATION (CONT.):

17. Supply

Ground

Wire

18. Wire

Nut

8. Fixture

Ground

Wire

20. Ground

Screw

21. White

Supply

Wire

22. Ribbed

Wire

23. Smooth

Wire

24. Black

Supply

Wire

9. Outlet

Box

15. Canopy

14. Screw Collar Loop

16. Threaded Ring

Fig. 11

Fig. 12

Page 13

Page 14

Possible Cause Corrective Action

1. Power is off. 1. Make sure power supply is on.

2. Faulty switch. 2. Test or replace switch.

3. Faulty wire connection. 3. Check wiring.

Fuse blows or circuit breaker

trips when light is turned on.

1. Crossed wires or power wire is grounding

out.

1. Check wire connections.

Light will not turn on.

TROUBLESHOOTING:

PRODUCT MAINTENANCE:

1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean

water, never a solvent) to wipe the surface of the fixture.

2. To clean the inside of the fixture, first disconnect power to the fixture by turning off the

circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly

dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the

fixture.

3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry soft

cloth to dust or wipe carefully.

LIMITED WARRANTY

The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a

period of two (2) years from date of purchase. This warranty applies only to the original consumer

purchaser and only to products used in normal use and service. If this product is found to be defective, the

manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of of the product at

the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse,

accident, modifications, alterations, neglect or mishandling. This warranty shall not apply to any product

that is found to have been improperly installed, set-up, or used in any way not in accordance with the

instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of

an accident, misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating to

faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product,

such as surface and/or weathering, as this is considered normal wear and tear. The manufacturer does not

warrant and specially disclaims any warranty, whether expressed or implied, of fitness for a

particular purpose, other than the warranty contained herein. The manufacturer specifically

disclaims any liability and shall not be liable for any consequential or incidental loss or damage,

including but not limited to any labor/expense costs involved in the replacement or repair of said

product.

HOME DEPOT SKU# 392-985(UPC# 046335942028)

Page 15

CINCO DE INTERIOR LUZ ARAÑA

MANUAL DE INSTRUCCIONES

Page is loading ...

MODE D’INSTALLATION

Page 29

LUSTRE LUMIÉRE INTÉRIEURE CINQ

HOME DEPOT UGS Nº 392-985 (CUP Nº 04633594028)

Page is loading ...

Hampton Bay HB3431-240 Installation guide

Hampton Bay HB3431-240 Installation guide

in other languages

Related papers

Other documents