Gigabyte GS-SR202T System Installation Manual

Brand: Gigabyte

Model: GS-SR202T

Category: Network equipment chassis

Type: System Installation Manual

This manual is also suitable for

GS-SR102T

Gigabyte GS-SR202T is an advanced server system with cutting-edge capabilities. Featuring dual socket 370 for Intel FC-PGA Pentium III or other compatible processors up to 1 GHz and above, it delivers exceptional processing power. The system boasts an AGPset chipset and ATI Rage XL VGA Chip for seamless graphics performance. With 4 168-pin 25-degree slant DIMM sockets, it supports up to 4.0GB of SDRAM, enabling efficient multitasking and handling of demanding applications. The GS-SR202T is equipped with Max 4 IDE ATA channels, providing versatile storage options for large datasets.

System Installation Guide

1-i

GS-SR102T/SR202T

System Installation Guide

1-ii

Table of Contents

1. INTRODUCTION 1-3

1.1. P

REFACE 1-3

1.2. F

EATURES 1-3

2. PACKAGE CONTENTS 2-1

3. SYSTEM INSTALLATION PROCEDURES 3-1

3.1. CHASSIS COVER REMOVAL 3-1

3.2. CPU INSTALLATION 3-2

3.3. HEAT SINK INSTALLATION 3-3

3.4. MEMORY INSTALLATION 3-5

3.5. PCI EXPANSION CARD INSTALLATION 3-5

3.6. AIR FLOW DUCT INSTALLATION GUIDE 3-7

3.7. REINSTALL TOP COVER 3-9

3.8. SCSI ID SETTINGS 3-10

3.9. J

UMPER SETTING FOR HD1 ‘HD2 AND HD3 3-11

3.10. DOCK HANDLES INSTALLATION 3-12

3.11. H

ARD DISK DRIVE INSTALLATION 3-12

3.12. FRONT PANEL 3-14

3.13. LED P

ANEL 3-14

3.14. REAR PANEL 3-15

3.15. DUAL LAN CARD INSTALLATION ( OPTIONAL ) 3-15

3.16. C

ONNECTOR ICONS 3-18

System Installation Guide

1-3

1. Introduction

1.1. Preface

This manual will assist you in installing all of the essential

components for rack mount system. We recommend you keep

this manual for future reference.

In order to maintain the rack mount server in its original

condition, please pay attention to the following tips.

1. Thoroughly read the manual before installing any

component.

2. Keep the system away from static and magnetic field.

3. Do not apply cleaning solutions directly to the system.

1.2. Features

The 1U Rackmount server contains the several features. These

features provide respective advantages to your system. The key

features of the adapter are:

Processor Support

 Dual Socket 370 for Intel FC-PGA Pentium III or other

compatible processor up to 1 GHz and above

 100/133MHz FSB

 AUTO detect CPU voltage

BIOS

 Support Dual BIOS technology ; 2M bit flash ROM

 IDE#0~#3 ,LS120 ,ZIP & CD-ROOM bootable

 AC recovery ON/OFF control

 AMI BIOS with enhanced ACPI feature for

PC99/Win98/Win2000 compliance

Green ,PnP ,DMI ,INT 13(>8.4GB) & Anti-Virus functions

 Auto-detect & report system health status

System Installation Guide

1-4

Chipset

 VIA Apollo Pro Family AGPset

( VT82C694X ,VT82C686A ) Chipset

 ATI Rage XL VGA Chip

 PROMISE PDC20265R

 Intel 82559 Dual LAN chip

Memory Support

 4 168-pin 25 degree slant DIMM sockets

 Supports PC-100/PC-133 SDRAM and VCM SDRAM

 Supports up to 4.0GB SDRAM

 Supports only 3.3V SDRAM DIMM

Storage Controller

 Max 4 IDE ATA channels ( 2 x ATA-66 and 2 x ATA-100

for IDE RAID 0 or 1 )

System Installation Guide

2-1

2. Package Contents

When opening the package, please insure the system has not

been damaged during shipping. Using the following list as a

check off, verify the contents. If there is missing component or

damage to the system, please inform your vendor immediately.

Contents：

System Chassis

Power Supply (installed)

GA-6ETXDR Motherboard (installed)

Slim type CD-ROM drive (installed)

Slim type Floppy drive (installed)

Three/Six Hard Disk Drive Trays for SR102/SR202

Two CPU heat sinks

Two Dock Handles, with tow screws

Driver & Application CD

Installation Manual

System Installation Guide

3. System Installation Procedures

Warning: Please remove the protective thin films (Top and

Bottom) from the system when installing.

3.1. Chassis Cover Removal

a. Unscrew the two thumb screws from the back of the system

(Fig-1).

b. Standing at the front of the system. Gently apply force to

the indentures with your thumbs and push toward the rear

of the chassis for about 3/4 of an inch. Top cover may be

lifted straight up (Fig-2).

Fig-1

c. With the top cover removed, you will see a plastic air duct

over the CPU and Memory. Remove the air duct to install

the CPU and Memory (Fig-3).

Fig-2

System Installation Guide

3-2

3.2. CPU Installation

To install Socket 370 CPU, lift up bar located next to the

Socket. Then, insert Socket370 CPU inside Socket, and

push the lever bar back into original position. (Fig-4 &

Fig-5 )

CPU-1

CPU-2

Fig-4

Fig-3

System Installation Guide

3.3. Heat Sink Installation

Click Fan+Heatsink to CPU socket 370 and plug the Fan power

cable to the each single CPU cooling Fan connector on the

motherboard. (Fig-6 and Fig-7)

Fig-5

Fig-6

System Installation Guide

3-4

For CPU1, Fan power cable connect to J13 (CPU1 FAN)

connector and for CPU2, Fan power cable connect to J15 (CPU2

Fan) Connector. Note to make sure the connector is plugged into

the header in the correct and firmly seated. (Fig-8)

J13-CPU1 Fan Connector

J15-CPU2 Fan Connector

Fig-7

Fig-8

System Installation Guide

3.4. Memory Installation

The motherboard contains four slanted DIMM (Dual Inline

Memory Module) sockets. The system BIOS will auto detect the

size of the memory. To install memory, simply push the memory

modules into the DIMM sockets. (Fig-9)

Fig-9

3.5. PCI Expansion Card Installation

GS SR102 provides one expansion raiser slot for a peripheral

card, 64Bit/66 MHz full length. To install the peripheral, please

follow these few steps.

a. There are three screws holding the raiser bracket. First,

remove the screw on the top of the bracket (Fig-10) then

remove the two screws located at the rear. (Fig-11).

System Installation Guide

3-6

b. Carefully remove the PCI raiser bracket. (Fig-12).

c. Install the card into place. Secure the card with screw

(Fig-13), make sure it is seated properly into PCI slot.

d. Replace the raiser bracket into the PCI slot on the

motherboard (Fig-14).

Fig-12

Fig-13

Fig-10

Fig-11

System Installation Guide

3-7

3.6. Air Flow Duct Installation Guide

GS-SR102 and GS-SR202 have installed a new device called

Air Flow Duct. The main function of Air flow duct is its

capability of driving out excessive system heat(Especially the

CPU Heat). In order to maintain the smooth system operation,

please note that after CPU and RAM have being installed.

Remember to apply the air flow duct back onto the system to

ensure consistent system operation. We will differentiate those

two air flow duct installation guide on the following steps:

(1.) SR-102：

Please insert the Air Flow Duct following the arrow(Fig-16)。

After smoothly insert the Air Flow Duct, please pay attention to

the stable clip circle on Fig-17. Stable Circle must complete

insert in the Air Flow Stable Rack.

Fig-18 indicates Air Flow Duct should be flat and completely insert

into the system. When the upper case is placed, please be aware that

Power Supply header and motherboard should be completely insert

under the duct cover. Otherwise the upper case might not able to

close tightly.

Fig-14

Fig-15

System Installation Guide

3-8

（Fig-15）

(2.) SR-202：

a. Facing the back-side of system, insert the Air Flow Duct

diagonally（Fig-19）。

b. On the other side of Air Flow Duct, follow the above

instruction again.（Fig-20）。

c. Finally, completely insert the Power Cable and header

inside the Air Flow Duct to ensure the heat flow out

smoothly.

Attention: There are pressure from both front and back

end, therefore the slight pop up at middle is nature.

Fig-16

Fig-17

Fig-18

System Installation Guide

3-9

3.7. Reinstall Top Cover

When you are finish installing all the essential components from

section 3.1 to 3.5, replace the transparent plastic air duct. This

will ensure the air flow inside the chassis. Failure to do so may

cause CPU and Memory to over heat.

Replace the top cover, insuring that the thumb screws are tighten.

(Fig-22)

Fig-19 Fig-20

Fig-21

System Installation Guide

3-10

3.8. SCSI ID Settings

The SCSI ID is preset as shown in Fig-23 during manufacture. If

there is a abnormal SCSI hard disk drive behavior e.g. does not

find hard disk drive properly, please make sure HD1, HD2 and

HD3 have different IDs.

Fig-22

Fig-23

System Installation Guide

3-11

3.9. Jumper setting for HD1 ‘ HD2 and HD3

Jumper

D C B A

0 ON ON ON ON

1 ON ON ON OFF

2 ON ON OFF ON

3 ON ON OFF OFF

4 ON OFF ON ON

5 ON OFF ON OFF

6 ON OFF OFF ON

7 ON OFF OFF OFF

8 OFF ON ON ON

9 OFF ON ON OFF

A OFF ON OFF ON

B OFF ON OFF OFF

C OFF OFF ON ON

D OFF OFF ON OFF

E OFF OFF OFF ON

F OFF OFF OFF OFF

ON( Jumper Close ):1-2 OFF( Jumper Open ):2-3

System Installation Guide

3-12

3.10. Dock Handles Installation

Remove dock handles from the package. Put two on each side of

the chassis, secure with screws provided (Fig-24).

3.11. Hard Disk Drive Installation

Pull the hard disk drive tray handle and remove the tray from the

chassis (Fig-25). Insert 80-pin SCA SCSI hard disk drive into

the tray. Secure each hard disk drive with screws (Fig-26).

Fig-24

Fig-25 Fig-26

System Installation Guide

3-13

After hard disk drive is secure with the screws hold the hard

drive handle at open position and insert the tray into chassis

（Fig-27）. When the hard disk drive connector meets the SCSI

back plane, push the hard disk drive tray handle to the closed

position.（Fig-28）

Fig-27 Fig-28

System Installation Guide

3-14

3.12. Front Panel

SR-102

SR-202

3.13. LED Panel

Power LED: Green－Online

Off－Offline

LAN Activity: Green－Online

Off－Offline

Flashing－LAN Activity

LAN Activity

Power LED

USB

Connector

Fan Status

System

Status

USB & LED

Serial Port Floppy Drive CD-ROM Drive

Serial Port

Floppy Drive

CD-ROM Drive

USB & LED

Page is loading ...

Gigabyte GS-SR202T System Installation Manual

Brand: Gigabyte

Model: GS-SR202T

Category: Network equipment chassis

Type: System Installation Manual

This manual is also suitable for

GS-SR102T

Download PDF

report

Gigabyte GS-SR202T System Installation Manual

This manual is also suitable for

Gigabyte GS-SR202T System Installation Manual

Related papers

Other documents