CMA Dishmachines 180 TALL CORNER Quick Installation Guide
- Category
- Dishwashers
- Type
- Quick Installation Guide
This manual is also suitable for
CMA-180/180Tall
Quick Setup
Instructions
1
STEP
WALL
DRAIN
8"
FLOOR DRAIN
Connect a 2" drain pipe (not supplied) from
scrap accumulator to floor or wall drain.
Connect dishmachine to hot water source-
minimum 140°F if unit is equipped with a
booster heater. If 140°F is not available,
order a 2 minute time cycle (120°F minimum
temperature required). A minimum of 180°F
is required if unit is not equipped with a
booster heater.
3 Phase: Connect power supply wires, L1, L2
and L3 to the appropriate terminals marked
L1, L2 and L3 on the power block. Important:
If one of the three wires has higher voltage it
must be inserted as L-2.
Remove the plug from the mixing chamber
and install the rinse injection fitting (rinse
injection fitting provided by your dispenser
supplier; CMA does not supply).
Remove the plastic plug to install the
detergent fitting (provided by your
dispenser supplier; CMA does not
supply).
3
STEP
L2
L3
L1
208/240
3 PHASE OR SINGLE
PHASE
L1 OR L3
FOR SINGLE PHASE
DRAIN
CONNECTION
1
DETERGENT
FITTING INLET
4
WATER INLET
2
MIXING
CHAMBER
5
POWER
BLOCK
3
CMA-180
REAR VIEW
4
STEP
PLASTIC
PLUG
PLUG
5
STEP
WARNING: Electrical and plumbing connections
need to be made by a licensed service person
and comply with all Federal, State and Local
Health, Electrical, Plumbing and Safety codes.
2
STEP
11-2016
PN: 10130.15
7
STEP
Press "POWER ON/OFF" rocker switch to turn on
dishmachine.
8
STEP
Press "AUTO FILL" immediately after power
is turned on. Timer will automatically fill until the
water overflows into the scrap trap. The initial fill
may need to be pushed twice to fill wash tank.
9
STEP
Open dishmachine doors completely. Closing the
doors will automatically activate the machine.
AUTO FILL
8
CYCLE LIGHT
BLACK/YELLOW
STRIPED WIRE
POWER
ON OFF
7
RINSE TOGGLE
SWITCH
6
DOOR
HANDLE
9
HEATER
THERMOSTAT
10
BOOSTER
HEATER
10
Adjust the temperature by removing the panel in front
of the respective heater and turning the adjustment
post. Wash temp. 155°F. Rinse temp.180°F.
STEP
Remove the stainless steel plug to install the
detergent probe (provided by your dispenser
supplier; CMA does not supply).
11
STEP
11-2016
CMA-180
FRONT VIEW
WARNING: Electrical and
plumbing connections
need to be made by a
licensed service person
and comply with all Federal,
State and Local Health,
Electrical, Plumbing and
Safety codes.
DETERGENT
PROBE INLET
11
WASH TANK
HEATER
10
BOOSTER HEATER DAMAGE PREVENTION
CAUTION: TO PREVENT BOOSTER HEATER ELEMENT DAMAGE, CMA HAS REMOVED A WIRE FROM
THE “HIGH-LIMIT SWITCH”. THE BOOSTER TANK MUST BE FILLED WITH WATER PRIOR TO
CONNECTING THE “REMOVED” WIRE, AT THE INITIAL FILLING OF A NEWLY INSTALLED DISHMACHINE.
TO FILL THE BOOSTER TANK, LOCATE THE “RINSE TOGGLE SWITCH” ON BACK OF CONTROL BOX.
PUSH THE TOGGLE SWITCH TO ACTIVATE THE WATER SOLENOID THAT FILLS THE BOOSTER TANK.
THE BOOSTER TANK INDICATES FULL, WHEN YOU CAN OBSERVE WATER SPRAYING FROM THE RINSE
ARMS. AT THIS POINT, AND ONLY AT THIS POINT, SHOULD YOU CONNECT THE “REMOVED” WIRE.
FAILING TO FOLLOW THESE IMPORTANT INSTRUCTIONS WILL DESTROY THE HEATING ELEMENT,
BECAUSE THE ELEMENT SHOULD ONLY OPERATE WHEN FULLY SUBMERGED IN WATER.
10
Push "RINSE TOGGLE SWITCH”, located on the back
of the control box, to fill the booster tank.
6
STEP
THERMOMETERS
CMA-180/180Tall
Quick Setup
Instructions
The Spirit of Excellence
an Ali Group Company
-
1
-
2
CMA Dishmachines 180 TALL CORNER Quick Installation Guide
- Category
- Dishwashers
- Type
- Quick Installation Guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
CMA Dishmachines CMA-180 Owner's manual
-
-
-
-
CMA Dishmachines EST-66 TALL User manual
-
CMA Dishmachines L-1X User manual
-
-
-
CMA Dishmachines C User manual
-