-2-
NOTE: It is IMPORTANT TO FOLLOW ALL of the
manufacturers instructions for the grinder that will
be used. Failure to do so may cause injury!
1. Place the Auger, spline end rst, into the
Juicer Head (Figure A).
2. Align the tabs on the Screen with the
notches in the opening on the Juicer Head.
Place the Screen onto the Auger.
3. Align the tabs on the Adjuster Cap with
the notches in the opening on the Juicer
Head. Place the Adjuster Cap onto the
Auger (Figure B). Twist the Adjuster Cap
counter-clockwise to lock the Adjuster Cap on
the Juicer Head.
4. Align the tabs on the Cap with the notches
on the Adjuster Cap. Twist the Cap counter-
clockwise to lock the Cap onto the Adjuster
Cap.
5. The Juicer Atachment is now assembled
(Figure C).
6. Align the splines on the Juicer Attachment
with the tabs on the motor unit (Figure D).
7. Press the Juicer Attachment against the
motor unit and rotate it counterclockwise until it
locks into place.
8. The Juicer Atachment is now ready for
use (Figure D).
9. Place the grinder tray (supplied with
the grinder) into the throat of the Juicer
Attachment. CAUTION! ALWAYS use the
stomper (supplied with the grinder) to push
food into the Juicer Attachmnet. NEVER
push food with hands.
ASSEMBLY INSTRUCTIONS
FIGURE A
NOTE: It is IMPORTANT TO FOLLOW ALL of the
manufacturers instructions for the grinder that will be used.
Failure to do so may cause injury!
1. Turn on the grinder.
2. Place the food that will be juiced into the throat of
the Juicer Attachment (Figure E).
3. Gently push the food into the Juicer Attachment
using the stomper. CAUTION! ALWAYS use the
stomper to push food into the Juicer Attachment.
NEVER push food with hands.
4. As the food is processed, the juice will come out
of the bottom Chute and any skin and seeds will come
out of the Cap. Place a bowl under the bottom Chute
and a bowl under the Cap to catch the juice and the
pulp. CAUTION! NEVER reach into the Juicer
Head.
HELPFUL HINTS: Rerun the skin and seeds through
the Juicer Attachment to extract any leftover pulp &
juice. Repeat as necessary.
NOTE: Twist the Cap to control the amount of
moisture in the pulp. The Adjuster Cap is marked “0”,
“1” or “2”. Be careful not to loosen the Cap from the
Adjuster Cap and the assembled Juicer Attachment
(Figure F).
USING THE JUICER ATTACHMENT
WARNING! Before cleaning, assembling or disassembling the grinder,
make sure the PLUG IS REMOVED FROM THE OUTLET/POWER SOURCE!
ALWAYS unplug the grinder when not in use.
FIGURE E
Stomper
RECIPES
Cap
-3-
Adjuster
Cap
Screen
Auger
Juicer
Head
FIGURE C
Auger
Splines
FIGURE B
Adjuster
Cap
(Back)
Screen
Auger
Juicer
Head
Tabs
Notches
FIGURE D
Splines
Assembled
Juicer
Attachment
Motor
Unit
Juicer
Attachment
Grinder
Tray
Stomper
Bottom
Chute
Cap
LARGE BATCH ITALIAN TOMATO SAUCE
1/2 cup olive oil 3 medium onions, chopped 2 cloves garlic, minced
3 Tbsp brown sugar 1 Tbsp dried oregano 4 tsp salt
2 tsp dried basil 1 tsp black pepper 12 cups fresh tomato puree
• Heat the olive oil in a large pan
• Sauté the onions and garlic until tender, do not overly brown
• Add the rest of the ingredients
• Bring mixture to a boil, reduce heat and simmer partially covered for 2 hours or until
sauce has reduced to desired consistency
• Stir occasionally
• Serve or allow to cool then refrigerate or freeze
• Ingredients like sliced mushrooms, cooked/drained sausage, hamburger,
etc. can be added to taste
FIGURE F
Cap
Adjuster Cap