Electrolux Z8010C User manual

Page is loading ...

The Electrolux Group. The world’s No. 1 choice.

822 86 29-01

Page is loading ...

2

Please keep both cover flaps open and cross reference pictures

with text where necessary.

Before you start, please refer to the electrical safety supply

instructions on page 63 (U.K. and Ireland only).

Clean air for healthier homes

Now that you have an Electrolux Oxy

3

silence Air Cleaner, you

will be breathing cleaner air. Obviously, you should locate this in

a room where you spend most time e.g. living room or bedroom.

Wherever there are people, plants or pets, there are airborne

particles that can affect your wellbeing, especially if you suffer

from allergies. For instance, did you know that the air inside a

room could be more polluted than the air in a large city? Scien-

tific studies have shown the following levels of particles per litre

of air:

Usually, you cannot see or smell particles in indoor air. But they

are there, and they can affect your health. If used in rooms of

the recommended size, your air cleaner reduces particle content

by at least 80% continuously. It reduces airborne particles in

a room, such as dust, pollen, spores, particles from animal fur

and industrial pollutants which improves the air quality. It will

also reduce the amount of bacteria and viruses.

Filtration in several stages

To guarantee the highest quality of air, the air cleaner has a

unique multi-stage electrostatic filtration system.

Stage 1 Two pre-filters remove large particles such as strands

of hair.

Stage 2 An electrostatic main filter reduces smaller airborne

particles. (See above)

Stage 3 Using a carbon filter* will also reduce gases and

odours in the indoor air. A carbon filter will reduce the air flow

somewhat. Remove the protective plastic, put the carbon filter

in place inside the air cleaner above the main filter and replace

the cover. The carbon filter is available as an accessory

(reference no. EF103) and can be used in all models.

For your safety

The Air cleaner is an electrical appliance and should be treated

accordingly. Follow these safety instructions and retain this

booklet for reference.

• The cleaner is only to be used by adults. Young children or

infirm persons should be supervised to ensure that they do not

play with the appliance.

• Do not use in humid places such as bathrooms. If liquid enters

the air cleaner, turn it off and have it inspected by an autho-

rised service station.

• Do not use outdoors.

• Do not use near flammable gases.

• Do not locate under a smoke alarm.

• Do not use if the lead or plug are damaged. To prevent

hazards, a damaged lead or plug must always be replaced

at an authorised Electrolux service station.

• Do not put objects on top of or inside the unit.

• Do not block the grills.

• Always disconnect from the power supply before removing the

filters for cleaning.

• Do not wash the main filter in salt water or dishwasher.

• Always change a damaged main filter.

Like other electrical appliances, the air cleaner may generate a

small amount of ozone. You might detect a faint smell (similar to

chlorine) especially when the unit is new. However, the amount

generated is extremely small and well below the limits stipulated

by the authorities. To reduce the amount of ozone you can fit

your Air cleaner with a carbon filter.

For best results

Place the air cleaner on the floor next to a wall. The Air cleaner

sucks in air at floor level and blows it out at the top. If there is a

wall mounted heater, place the air cleaner along the same wall

so that the rising warm air coincides with the air flow of the

cleaner. When using two or more units in one room, place them

along the same wall, as far apart as possible.

COUNTRYSIDE 1 million

CITY 100 million

IN THE HOME 100 million

HIGHWAY 1 billion

TOBACCO SMOKE 100 billion

Operating Instructions

1. Regulators* 10. Carrying handle

2. Buttons* 11. Power cord

3. Sound Sensor* 12. Compartment for unused cord

4. Reset button* 13. Top cover release button

5. Programme button* 14. Rating plate

6. Childproof lock button* 15. Indicator lamp*

7. Air inlet grills 16. Reserve wire/corona wire

8. Air outlet grills 17. Ionization chamber

9. Pre-filter door 18. Remote control*

*Only on certain models

Usage

All models are intended for continuous use at fan speed

setting 1 or any one of the automatic programmes*. The fan

speed setting can be changed to 2 or 3 if necessary.

The best results are achieved by leaving the air cleaner on

around the clock. (It uses less power than most light bulbs.)

Buttons

Controls the active programme. Press the button to

switch between and

manual mode.

Changes fan speed setting manually. Press the button

to switch between the different fan speeds.

Turns the air cleaner on and off.

Clean air delivery rate*)

(CADR +/-10% m

3

/h)

Position 1 130 110

Position 2 240 230

Position 3 380 380

Room size capacity (m

3

)

Position 1 27 23

Position 2 50 48

Position 3 79 79

Noise level (dBA)

(ISO 3741)

Position 1 31 28

Position 2 44 43

Position 3 63 63

Power consumption (W)

Position 1 30 30

Position 2 35 35

Position 3 70 60

*) = CADR measured without carbon filter.

Meets the safety requirements and ozone emission limits of

the IEC 60335-1 and 60335-2-65 directives. CE-certified.

English

Technical Specifications

220-240V/50-60HZ 100-110V/50-60Hz

3

Activates/deactivates the button lock. Press the

button for longer than two seconds to activate the

button lock. The indicator lamp will flash first and then

remain on while the lock is activated. The same pro-

cedure applies for deactivating the button lock.

Resets the air cleaner after washing the filter or after a

fault in the air cleaner. Press the button for longer than

two seconds. The indicator lamp will flash first and

then go out once the cleaner has been reset.

Functions (only models with automatic programmes and

functions)

A This program adjusts the fan speed according to the

degree of pollutants in the room.

B This program adjusts the fan speed according to the

noise level in the room. The air cleaner will operate at

the highest possible fan speed without increasing the

noise level in the room.

C This function can be used, for example, when coming

home after a day’s work to quickly clean the room

from pollutants. This programme has three different

modes.

The air cleaner automatically operates at setting 3.

After 15 minutes, it will automatically drop to setting 1.

The air cleaner will be turned off after two hours. The

fan speed setting is selected manually. The setting

can be changed during the preset operating duration.

The air cleaner will be turned off after nine hours.

Fan speed setting as above (2h).

D Indicates the degree of pollutants in the room. Adjust

to suitable fan speed setting or use auto program .

High degree of pollutants.

Medium degree of pollutants.

Low degree of pollutants.

E Indicates current fan speed setting.

F This symbol shows that the machine is operating

optimally and is supplying clean air. The symbol will

be extinguished and the respective fault indicator

lamp ( ) will come on when it’s time to wash

the filters or an air cleaner fault has occurred.

G Indicates that the filters should be cleaned according

to the cleaning schedule below.

H Indicates a fault in the air cleaner. Refer to the instruc-

tions under “Air cleaning problems”.

I With the button lock activated you can press all the

buttons without anything happening, which can be

used around children.

Cleaning and maintenance

Always disconnect the power supply prior to cleaning the unit.

Pre-filter

(a) Open the access door (9). (b) Take out the filters one at a

time and vacuum them. Use the brush accessory to avoid

damaging the filters. After cleaning filters insert and close the

door. The pre-filters do not need to be replaced. Follow this

procedure every two months or more often for sensitive people,

e.g. when vacuuming your home.

Main filter

(c) Press the button (13) and lift off the cover. (d) Take out and

vacuum the main filter first. Then, wash the filter by immersing

it in lukewarm water containing a mild detergent (no solvents).

After washing, rinse the filter with clean lukewarm water and

allow it to dry for at least 10 hours. If the filter is still damp

when you replace it in the air cleaner, you may hear a crackling

sound until the filter is completely dry.

Continue cleaning the air cleaner as follows (stage 3)

(e) Vacuum the grille at the top of the space. (f) Lift the grille

using the handle. (g) Remove the wire holder carefully with both

hands keeping it level and upright. (h) Vacuum the inside of the

cleaner, including the lower grille, with the brush or crevice

nozzle. If necessary, use a damp cloth with mild detergent.

(i) Carefully refit the wire holder using both hands and close

the grille. (If the wire is broken please refer to the troubleshoo-

ting section.) (j) Replace the main filter. Make sure the guides

are properly set in the grooves when you put the filter back.

(k) Replace the cover.

Resetting the air cleaner (stage 4)*

Press the reset button (4) after cleaning or replacement. The

warning lamp goes out to indicate that the air cleaner has

been reset. The air cleaner is reset automatically on models

that do not have a warning lamp.

Filter cleaning intervals

Depending on the level of ambient contamination, we recom-

mend that you follow the above procedure every two months or

when the indicator on the display lights up. The main filter may

need cleaning more frequently if dust is visible on the upper filter

surface.

Change the main filter at two or three-year intervals to ensure

the function of the air cleaner. (Reference no. of main filter

EF102.)

When using the carbon filter, replace every three to six months

or sooner if you are no longer able to detect a reduction in gases

and smells. Reference No EF103.

Troubleshooting air cleaner problems when fault

indicator on display comes on or the blue indicator

lamp changes colour to red (depending on model)

• A break in the corona wire (stage 1) is shown in figure (g)

and is used as a reference in the paragraph “Continue

cleaning the air cleaner as follows”.

Change the wire as instructed below. Press the reset button

(4). If the fault indicator comes on again after a short period,

proceed with the next stage.

Changing corona wire - Remove the broken wire. Carefully

replace the new wire as follows: Secure one end of the wire into

the groove. Bend the wire holder slightly and attach the other

end.

• Additional cleaning(stage 2)

Clean the filter and the ionization chamber inside the air

cleaner according to the maintenance instructions. Get in

touch with your service station if the fault indicator comes on

again after a short period.

Troubleshooting

• If the fan does not operate, (ie. if you cannot sense a weak air

current), check that the power cable is undamaged and that it is

connected to the power supply. Check that the cover and filters

are correctly set. If the fan still does not start, take your air clea-

ner to an authorised Electrolux service station for inspection.

• If a continuous crackling sound can be heard from the main

filter, lift up the filter and turn it 180°. If this does not remedy

the problem, take the unit for service. (A soft hissing coming

from the filter is normal, especially when new.)

• If the indicator lamp (15) does not light up though the fan is

operating, take the unit for service. (This applies only to air

cleaners without automatic functions.)

Refer also to further information from Electrolux at the end of

this brochure.

English

Page is loading ...

54

220-240 V/50-60 Hz 110-110 V/50-60 Hz

130 110

240 230

380 380

27 23

50 48

79 79

31 28

44 43

63 63

30 30

35 35

70 60

*) = CADR measured without carbon filter

*)

Page is loading ...

56

220-240 V/50-60 Hz 110-110 V/50-60 Hz

130 110

240 230

380 380

27 23

50 48

79 79

31 28

44 43

63 63

30 30

35 35

70 60

*) = CADR measured without carbon filter

*)

Page is loading ...

62

220-240 V/50-60 Hz 110-110 V/50-60 Hz

130 110

240 230

380 380

27 23

50 48

79 79

31 28

44 43

63 63

30 30

35 35

70 60

*) = CADR measured without carbon filter

*)

Page is loading ...

64

Electrical supply (UK and Ireland only)

Before you start … check the voltage

Before connecting the air cleaner to an electrical supply ensure that the

voltage marked on the data plate (on the reverse side of the air cleaner) is

correct for your electrical supply. If it is not, do not use the air cleaner but

refer back to your dealer.

Connecting to your electricity supply

Permanently connected to the air cleaner is a mains supply (2-core) cable

fitted with a non-rewirable plug incorporating a 13A fuse. In the event of the

fuse requiring replacement the fuse cover should be removed using a small

screwdriver. The old fuse MUST be replaced by a 13A ASTA approved

BS1362 fuse and the fuse cover must be replaced before the plug is used

again. In the event of loss of the fuse cover, replacements can be obtained

from your Electrolux dealer or Electricity Board and must be of the same

colour as indicated by the coloured insert on the base of the plug.

If difficulty is experienced in obtaining a replacement, contact your nearest

Electrolux Service Centre. (Please see the separate Electrolux Service

Organisation leaflet).

In no circumstances must the plug be used without a correct fuse

cover fitted.

If the plug that is fitted to your appliance is not suitable for your socket

outlet, it must be cut off and the appropriate plug fitted. Remove the fuse

from the cut off plug. The cut off plug should then be disposed of to prevent

the hazard of shocks in case it should be plugged into a 13 amp socket in

another part of your home.

The wires in the mains cable of this appliance are coloured in

accordance with the following code:

Blue: Neutral.

Brown: Live.

As the colours of the wires in the mains cable of this appliance may not

correspond with the coloured markings identifying the terminals in your

plug, proceed as follows:

The wire which is coloured blue must be connected to the terminal which is

marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the terminal which

is marked with the letter L or coloured red.

If using a three-pin plug, do not make any connection to the terminal

marked with the letter E or by the earth symbol or coloured green or

green-and-yellow. This cleaner is double insulated and no earth connection

is necessary.

It is in your interest to ensure that the plug is correctly attached to the

mains cable. In case of doubt, have it done by a qualified electrician, as

Electrolux cannot regard the repair of faults on the plug connection as a

service that can be given free of charge under the terms of the guarantee.

As a general guide to fitting any plug:

• Ensure the lengths of wire inside the plug are prepared correctly.

• Connections should be firmly made after all conductor strands are

entered into the terminal posts.

• When preparing the cable ends take care not to damage the outer

sheath, or the insulation surrounding the inner conductors.

•Tighten all screws.

• Replace the top cover of the plug and secure.

ANY PROBLEMS?

08706 055 055

CUSTOMER HELPLINE

DON’T TAKE

Something missing?

Don’t understand the instructions?

We are only a telephone call away.

Need more help?

IT BACK TO THE SHOP

65

English: Electrolux decline all responsibility for all damages arising from any

improper use of the appliance or in cases of tampering with the appliance.

Electrolux reserve the right to alter product appearance and/or specifications

without notice. Not all models featured are available in all countries.

Electrolux air cleaner features and accessories are protected worldwide by

Patents or Registered Designs.

This product is designed with the environment in mind. All plastic parts are

marked for recycling purposes.

For details see our website: www.electrolux.com

Deutsch: Electrolux übernimmt keine Verantwortung für Schäden, die durch

den unsachgemäßen Einsatz des Geräts oder unbefugten Eingriff in den

Staubsauger entstehen.

Electrolux behält sich das Recht vor, Form bzw. Eigenschaften des Geräts ohne

Vorankündigung zu ändern. Alle abgebildeten Modelle sind nicht in allen

Ländern erhältlich.

Electrolux Luftreinigereigenschaften und Zubehörteile sind weltweit durch

Patente oder eingetragene Designs geschützt.

Das Design dieses Produkts ist umweltfreundlich. Alle Kunststoffteile sind zur

Wiederverwertung gekennzeichnet.

Einzelheiten finden Sie auf unserer Webseite: www.electrolux.com

Français: Electrolux décline toute responsabilité concernant tous les

dommages découlant d’une mauvaise utilisation de l’appareil ou en cas de

modification de l’appareil.

Electrolux se réserve le droit de modifier l’aspect du produit et/ou les carac-

téristiques sans préavis. Tous les modèles présentés ne sont pas disponibles

dans tous les pays.

Le purificateur d’air Electrolux et ses accessoires sont protégés dans le monde

entier par des Brevets ou des Modèles Déposés.

Ce produit a été conçu dans le respect de l’environnement. Toutes les pièces

plastiques sont marquées dans le but de les recycler.

Pour plus d’informations, veuillez consulter notre site internet:

www.electrolux.com

Español: Electrolux declina toda responsabilidad de cualquier daño

ocasionado por el uso incorrecto de este aparato o en casos en que se haya

reformado indebidamente.

Electrolux se reserva el derecho de alterar la apariencia del producto y/o las

especificaciones sin previo aviso. No todos los modelos presentados se hayan

a disposición en todos los países.

Las funciones del purificador de aire y los accesorios Electrolux están

protegidos en todo el mundo por Patentes o Diseños Registrados.

Este producto ha sido diseñado teniendo en cuenta el medio ambiente. Todas

las piezas de plástico llevan el distintivo de reciclaje.

Para obtener más detalles le invitamos a que visite nuestra página web:

www.electrolux.com

Italiano: L’Electrolux declina ogni responsabilità per i danni derivati dall’uso

improprio dell’apparecchio o se stesso è stato manomesso.

L’Electrolux si riserva il diritto di modificare l’aspetto del prodotto e/o le sue

caratteristiche tecniche senza preavviso. Non tutti i modelli descritti sono

disponibili in tutti i Paesi.

Le caratteristiche e gli accessori degli purificatore d’aria Electrolux sono protetti

in tutto il mondo da brevetti o come modelli depositati.

Questo prodotto è stato ideato tenendo presente considerazioni ambientali.

Tutte le parti in plastica sono contrassegnate a scopo di riciclaggio.

Per maggiori dettagli vedere il nostro sito web: www.electrolux.com

Português: A Electrolux não aceita qualquer responsabilidade por danos

resultantes do uso impróprio do aparelho ou em casos de interferência

indevida com o mesmo.

A Electrolux reserva-se o direito de alterar o aspecto do produto e/ou as

especificações sem qualquer aviso. Nem todos os modelos apresentados estão

disponíveis em todos os países.

As características e acessórios do purificador de ar Electrolux estão protegidos

mundialmente por Patentes ou Designs Registados.

Este produto foi projectado pensando-se no meio ambiente. Todos as partes de

plástico estão marcadas para serem recicladas.

Para obter pormenores consulte o nosso website: www.electrolux.com

Nederlands: Electrolux wijst alle verantwoordelijkheid af voor eventuele

schade die voortkomt uit het niet-geëigend gebruik van het apparaat of in

gevallen waarbij op het apparaat krachtig wordt gedrukt.

Electrolux behoudt zich het recht voor om het uiterlijk van het product of

specificaties zonder wederbericht te veranderen. Alle modellen die besproken

worden zijn niet verkrijgbaar in alle landen.

De functies van de Electrolux luchtreiniger zijn beschermd door patenten of

gedeponeerde ontwerpen.

Dit product werd ontworpen met zorg voor het milieu. Alle plastic onderdelen

kunnen hergebruikt worden.

Meer informatie vind u op onze website: www.electrolux.com

Dansk: Electrolux fralægger sig ethvert ansvar for skader forårsaget af forkert

brug af støvsugeren samt ændringer udført på apparatet.

Electrolux forbeholder sig ret til at udføre ændringer på produktets udformning

og/eller specifikationer uden varsel. De beskrevne modeller er ikke alle til

rådighed i alle lande.

Electrolux luftrenserens udstyr og tilbehør er beskyttet globalt under patenter

eller registrerede varemærker.

Dette produkt er miljøvenligt fremstillet. Alle plastikdele er afmærket til

genbrugsformål.

For yderligere oplysninger henvises til vores webside: www.electrolux.com

Service og reservedele

Service bestilles hos Electrolux Service A/S på tel. 70 11 74 00 eller fax 75

91 44 43. Reservedele: Private bestiller hos nær-meste forhandler eller på

telefon 86 25 02 11 og forhandlere bestiller på telefon 45 88 77 55.

Reservedele og tilbehør kan også bestilles on-line på http://www.electrolux.dk

Page is loading ...

Electrolux Z8010C User manual

This manual is also suitable for

Electrolux Z8010C User manual

in other languages

Related papers

Other documents