BOTTOM FREEZER
REFRIGERATOR
User’s Guide
Please read this guide thoroughly before operating
and keep it handy for reference at all times.
ХОЛОДИЛЬНИК С
НИЖНЕЙ
МОРОЗИЛЬНОЙ
КАМЕРОЙ
Руководство
пользователя
Прочтите внимательно настоящее
Руководство, прежде чем приступать к
эксплуатации вашего холодильника, и держите
настоящее Руководство постоянно "под рукой"
для консультаций.
P/No. 3828JL8097WP/No. 3828JL8097W
2
TABLE OF CONTENTS
English Version 2
Safety Instructions 3–4
Parts and Features 5
Refrigerator Installation 6–13
Unpacking Your Refrigerator 6
Installation 6
Removing and Replacing
Your Refrigerator Handles
and Doors 7–12
Base Cover 13
Leveling and Door Alignment 13
Using Your Refrigerator 14–25
Setting the Controls 14
Ensuring Proper Air Circulation 14
Diagnosis(Failure Detection)
Function 15
How To Use A New Door Ice
Bucket 16
Adjusting Control Settings 17
Food Storage Guide 17
Storing Frozen Food 18
Refrigerator section
Water Dispenser 18
Refrigerator Shelves 19
Bottle Holder (Optional) 19
Snack Pan 20
Optibin Crisper 20
Crisper Humidity Control 20
Removing Crisper 20–21
Crisper Cover with Lattice on
inner Surface 21
Dairy Bin (Optional) 22
Modular Door Bin 22
Egg Box (Optional) 22
Freezer section
Tilting Door 23
Ice Bin 23
Tilt- Out Door Basket (Optional) 23
Durabase 24
Durabase Divider 24
Pull out Drawer 24
Filter 25
Care and Cleaning 26–27
General Cleaning Tips 26
Outside 26
Inside Walls 26
Door Liner and Gaskets 26
Plastic Parts 26
Condenser Coils 26
Light Bulb Replacement 26–27
Power Interruptions 27
When you go on vacation 27
When you move 27
About the Automatic Icemaker 28
Connecting the Water Line 29–31
Troubleshooting Guide 32–35
This guide contains many important safety messages. Always read and obey all safety messages.
This is the safety alert symbol. It alerts you to safety messages that inform you of hazards
that can kill or hurt you or others, or cause damage to the product.
All safety messages will be preceded by the safety alert symbol and the hazard signal word
DANGER, WARNING, CAUTION. These words mean:
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electric shock, or
injury to persons when using your product,
basic safety precautions should be followed,
including the following:
Read all instructions before using this appliance.
• NEVER unplug your refrigerator by pulling on the
power cord. Always grip the plug firmly and pull it
straight out from the outlet.
• Repair or replace immediately all electric service
cords that have become frayed or otherwise
damaged. Do not use a cord that shows cracks or
abrasion damage along its length or at either the
plug or connector end.
• When moving your refrigerator away from the wall,
be careful not to roll over or damage the power cord.
• DO NOT store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
• DO NOT allow children to climb, stand or hang on
the refrigerator doors or shelves in the refrigerator.
They could damage the refrigerator and seriously
injure themselves.
• Keep fingers out of pinch point areas; clearances
between the doors and cabinet are necessarily
small. Be careful closing doors when children are
in the area.
• Unplug your refrigerator before cleaning or making
any repairs.
NOTE: We strongly recommend that any servicing
be performed by a qualified individual.
• Before replacing a burned-out light bulb, unplug
the refrigerator or turn off power at the circuit
breaker or fuse box in order to avoid contact with a
live wire filament. (A burned-out light bulb may
break when being replaced.)
NOTE: Setting either or both controls to the OFF
position does not remove power to the light circuit.
• This refrigerator must be properly installed in
accordance with the Attention Installer
Instructions that were taped to the front of the
refrigerator.
• After your refrigerator is in operation, do not touch
the cold surfaces in the freezer compartment when
hands are damp or wet. Skin may adhere to the
extremely cold surfaces.
• In refrigerators with automatic icemakers, avoid
contact with the moving parts of the ejector
mechanism, or with the heating element that
releases the cubes. DO NOT place fingers or
hands on the automatic icemaking mechanism
while the refrigerator is plugged in.
• DO NOT refreeze frozen foods which have thawed
completely. The United States Department of
Agriculture in Home and Garden Bulletin No. 69 says:
…You may safely refreeze frozen foods that have
thawed if they still contain ice crystals or if they are
still cold—below 4°C.
…Thawed ground meats, poultry or fish that have
any off-odor or off-color should not be refrozen and
should not be eaten. Thawed ice cream should be
discarded. If the odor or color of any food is poor
or questionable, get rid of it. The food may be
dangerous to eat.
Even partial thawing and refreezing reduces the
eating quality of foods, particularly fruits, vegetables
and prepared foods. The eating quality of red meats
is affected less than that of many other foods. Use
refrozen foods as soon as possible to save as much
of their quality as you can.
• Do not modify or extend
the Power Cord length.
It will cause electric shock
or fire.
You will be killed or seriously injured if you don’t follow instructions.
You can
be killed or seriously injured if you don’t follow instructions.
Indicates an imminently hazardous situation which, if not avoided,
may result in minor or moderate injury, or product damage only.
All safety messages will identify the hazard, tell you how to reduce the chance of injury and tell you
what can happen if the instructions are not followed.
3
SAVE THESE INSTRUCTIONS
WARNING
CAUTION
WARNING
DANGER
Child entrapment and suffocation are not
problems of the past. Junked or abandoned
refrigerators are still dangerous…even if they will
sit for just a few days. If you are getting rid of
your old refrigerator, please follow the
instructions at right to help prevent accidents.
BEFORE YOU THROW AWAY
YOUR OLD REFRIGERATOR
OR FREEZER
• Take off the doors.
• Leave the shelves in place so
that children may not easily
climb inside.
4
DANGER:
RISK OF CHILD ENTRAPMENT
CFC DISPOSAL
Your old refrigerator may have a cooling system
that used CFCs (chlorofluorocarbons). CFCs are
believed to harm stratospheric ozone.
If you are throwing away your old refrigerator,
make sure the CFC refrigerant is removed for
proper disposal by a qualified servicer. If you
intentionally release this CFC refrigerant, you can
be subject to fines and imprisonment under
provisions of environmental legislation.
IMPORTANT SAFETY INSTRUCTIONS
Don’t use an extension cord
If possible, connect the refrigerator to its own
individual electrical outlet to prevent it and other
appliances or household lights from causing an
overload that could cause a power outage.
Accessibility of Supply Plug
The refrigerator-freezer should be so positioned
that the supply plug is accessible for quick
disconnection when accident happens.
Supply Cord Replacement
If the supply cord is damaged, it must be
replaced by the manufacturer or its service agent
or a similarly qualified person in order to avoid a
hazard.
FEED WATER PIPE INSTALLATION
Before installation
• Automatic ice maker can be installed only by
manufacturer.
• Automatic ice maker operation needs water
pressure of 147~834 kPa (1.5~8.5 kgf/cm
2
)
(That is, an instant paper cup (180 cc) will be
fully filled within 3 sec.).
• If water pressure does not reach the rating
147 kPa (1.5 kgf/cm
2
) or below, it is necessary
to purchase a separate pressure pump for
normal automatic icing and cool water feed.
• Keep the total length of the feed water pipe tube
within 8 m and be careful for the tube not be
bent. If the tube is 8 m or longer it may cause
trouble in water feed owing to the drain water
pressure.
• Install the feed water pipe tube at a place free
from heat.
WARNING
•
Connect to potable water supply
only.
• Refer to instructions with water filter kit for
installation.
WARNING
• The refrigerant and insulation blowing gas used
in the appliance require special disposal
procedures. When disposal, please consult with
service agent or a similarly qualified person.
PARTS AND FEATURES
Use this page to become more familiar with the parts and features. Page references are included for
your convenience.
NOTE: This guide covers several different models. The refrigerator you have purchased may
have some or all of the items listed below. The locations of the features shown below may not
match your model.
Refrigerator Light
Filter (Inside)
Modular Door Bins
Refrigerator Shelves
Optibin Crisper
(Keeps fruits and vegetable fresh
and crisper)
Ice Room (Ice Maker and Ice Bucket)
Pull out Drawer
Turbo Motor
Tilt-Out Door Basket (optional)
Durabase
Divider
Ice Bin
Water Tank Cover
Snack Pan
Egg Box (optional)
Dairy Bin (optional)
Bottle Holder (optional)
5
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
Q
A
B
F
N
M
E
L
I
H
G
K
J
P
C
D
Q
C
O
Ice Bucket
Ice Room Door
UNPACKING YOUR REFRIGERATOR
Remove tape and any temporary labels from your
refrigerator before using. Do not remove any
warning-type labels, the model and serial number
label, or the TechSheet that is attached to back
wall of the refrigerator.
To remove any remaining tape or glue, rub the
area briskly with your thumb. Tape or glue residue
can also be easily removed by rubbing a small
amount of liquid dish soap over the adhesive with
your fingers. Wipe with warm water and dry.
Do not use sharp instruments, rubbing alcohol,
flammable fluids or abrasive cleaners to remove
tape or glue. These products can damage the
surface of your refrigerator. For more information,
see the Important Safety Instructions section.
Refrigerator shelves are installed in the shipping
position.
Please reinstall shelves according to your
individual storage needs.
INSTALLATION
1. To avoid vibration, the unit must be level. If
required, adjust the leveling screws to
compensate for unevenness of the floor. The
front should be slightly higher than the rear to
aid in door closing. Leveling screws can be
turned easily by tipping the cabinet slightly. Turn
the leveling screws clockwise ( ) to raise the
unit, counterclockwise ( ) to lower it.
2. Install this appliance in an area where the
temperature is between 13°C and 43°C. If the
temperature around the appliance is too low or
high, cooling ability may be adversely affected.
3.
To ensure proper air circulation around the
fridge -freezer, please maintain sufficient space
on both the sides as well as top and maintain at
least 2.8 inches (7 cm) from the rear wall.
CAUTION: Avoid placing the unit near heat
sources, direct sunlight or moisture.
NEXT
1. Clean your refrigerator thoroughly and wipe off
all dust accumulated during shipping.
2. Install accessories such as ice cube bin,
drawers, shelves, etc., in their proper places.
They are packed together to prevent possible
damage during shipment.
3. Let your refrigerator run for at least 2 or 3 hours
before putting food in it. Check the flow of cold
air in the freezer compartment to ensure proper
cooling. Your refrigerator is now ready for use.
WARNING
• Be careful when you work with hinge, base
grille, stopper etc. You may be injured.
• Do not put hands or foot or metal sticks into air
vents, base grille or bottom of refrigerator. You
may be injured or receive an electrical shock.
REFRIGERATOR INSTALLATION
6
WARNING
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other injury.
WARNING
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the
refrigerator for cleaning or service, be sure to
protect the floor. Always pull the refrigerator
straight out when moving it. Do not wiggle or
walk the refrigerator when trying to move it, as
floor damage could occur.
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion
or fire.
REFRIGERATOR INSTALLATION
HOW TO REMOVE DOOR HANDLES
To move refrigerator through a house door, it maybe necessary to remove the refrigerator door
handles.
NOTE: Handle appearance may vary
from illustrations on this page.
1. Removing Refrigerator Handle
• Grasp the handle tightly with both
hands and slide the handle up
(1)(this may require some force).
• The keyhole slots (2) on the back
of the handle allow the handle to
separate from the mounting
screws (3).
CAUTION: The handle could be
damaged if you hit it with a
hammer while removing or
attaching.
CAUTION: When you assemble
or disassemble handle, you must
push and pull with moment force.
2. Removing Freezer Drawer Handle
• Press the handle against door
first.
• Grasp the handle tightly with
both hands and slide the handle to
right (1) (this may require some
force).
• The keyhole slots (2) on the back
of the handle allow the handle to
separate from the mounting
screws (3).
7
1
1
3
2
3
1
1
2
Keyhole slots
on back of
handle
Keyhole slots
on back of
handle
Screws
mounted
on door
Screws
mounted
on door
REFRIGERATOR INSTALLATION
HOW TO REPLACE DOOR HANDLES
NOTE: Handle appearance may vary from
illustrations on this page.
1. Replacing Refrigerator Door Handle
• Align keyhole slots (1) on the top and
bottom of the back of the handle with
the screws (2) mounted on the front of
the door.
• Press the handle against the door
front, making sure that the screws (2)
go into the keyhole slots (1).
• Holding the handle with both hands,
press it firmly against the front of the
door and slide the handle down (3).
2. Reinstalling the Freezer Drawer
Handle
• Align keyhole slots (4) on the right
and left sides of the back of the
handle with the screws (5) mounted
on the front of the drawer.
• Press the handle against the drawer
front, making sure that the screws
(5) go into the keyhole slots (4).
• Holding the handle with both hands,
press it firmly against the front of the
drawer and slide the handle to the
left (6).
8
2
3
1
1
6
6
5
4
Keyhole slots
on back of
handle
Screws
mounted
on door
Screws
mounted
on door
REFRIGERATOR INSTALLATION
REMOVING AND REPLACING REFRIGERATOR DOORS
1. Removing Refrigerator Door
CAUTION: Before you begin, unplug the refrigerator. Remove food and bins from doors.
uu
Left Door - FIG.2
1. Disconnect water supply tube by pushing back on the disconnect ring (3). - FIG.1
2. Open door. Loosen top hinge cover screw (1).
Use flat tip screwdriver to pry back hooks on front underside of cover (2). Lift up cover.
3. Remove cover.
4. Pull out the tube.
5. Disconnect the three wire harnesses (4). Remove the grounding screw (5).
6. Rotate hinge lever (6) counterclockwise and remove. Lift top hinge (7) free of hinge lever latch (8).
CAUTION: When lifting hinge free of latch, be careful that door does not fall forward.
7. Lift door up from middle hinge pin (9) and remove door.
8. Place door, inside facing up, down onto a non-scratching surface.
uu
Right Door - FIG.3
1. Open door. Loosen top hinge cover screw (1). Lift up cover (2).
2. Remove cover.
3. Disconnect wire harness (4). Remove the grounding screw (5).
4. Rotate hinge lever (6) clockwise and remove. Lift top hinge (7) free of hinge lever latch (8).
CAUTION: When lifting hinge free of latch, be careful that door does not fall forward.
5. Lift door up from middle hinge pin (9) and remove door.
6. Place door, inside facing up, down onto a non-scratching surface.
9
1
2
3
5
6
7
8
4
1
2
6
7
8
5
4
3
FIG.2 FIG.3
FIG.1
REFRIGERATOR INSTALLATION
2. Reinsalling the Refrigerator Door
uu
Right Door
1. Lower the door onto middle hinge pin (9).
2. Fit top hinge (7) over hinge lever latch (8) and into place. Insert hinge lever (6) under lever latch.
Rotate lever counterclockwise to secure hinge.
3. Install the grounding screw (5) and connect wire harnesses (4).
4. Hook tab on door switch side of cover under edge of wire opening in cabinet top. Position cover (2)
into place. Insert and tighten cover screw (1).
uu
Left Door
1. Lower the door onto middle hinge pin (9).
2. Fit top hinge (7) over hinge lever latch (8) and into place. Insert hinge lever (6) under lever latch.
Rotate lever clockwise to secure hinge.
3. Install the grounding screw (5) and connect the three wire harnesses (4).
4. Push the water supply tube into the hall on the top case and pull it out on the backplate.
5. Insert the water supply tube (3) into the connector tube until you see only one scale mark.
(Fully insert the tube over 5/8”(15mm)).
6. Hook tab on door switch side of cover (2) under edge of wire opening in cabinet top. Position cover
into place. Insert and tighten cover screw (1).
10
9
9
Correct
Incorrect
HOW TO REMOVE AND INSTALL
THE PULLOUT DRAWER
IMPORTANT: To avoid possible injury or product
or property damage, you will need two people to
perform the following instructions.
1. Removing Pullout Drawer
• Pull the drawer open to full extension. Remove
the lower basket (1) by lifting basket from rail
system. (If you tilt the door, it will be easier.)
• Press both hangers with your thumbs to lift it up.
• Separate the left and right rail cover.
• Remove the screws (2) of the rail on both sides.
• With both hands, hold both sides of the door
and pull it up to separate it from the rails.
• With both hands, hold the center bar and push it
in to let both rails fitted simultaneously.
CAUTION: When you remove the drawer, do
not hold the handle. If it may come off and it
could cause personal injury.
CAUTION: When laying the drawer down, be
careful not to damage the floor or hurt your feet
by the sharp edges on hinge side.
REFRIGERATOR INSTALLATION
1
2
11
REFRIGERATOR INSTALLATION
HOW TO REMOVE AND INSTALL
THE PULLOUT DRAWER
IMPORTANT: To avoid possible injury or product
or property damage, you will need two people to
perform the following instructions.
2. Installing Pullout Drawer
• With both hands, hold the center bar and push it
out to let both rails out to full extension
simultaneously.
• Hook door supports (1) into rail tabs (2).
• Lower door into final position and tighten the
screws (3).
• Make sure you have a right rail cover for each
side.
• Align the top holes of the rail cover with the top
holes of the door supports to assemble the rail
covers.
• With the drawer pulled out to full extension,
insert the lower basket (4) in the rail assembly.
WARNING: To prevent accidental child and
pet entrapment or suffocation risk. DO NOT
allow them to play inside of drawer.
WARNING: DO NOT step or sit down on
freezer door.
12
4
1
2
3
Right
Rail Cover
Left
Rail Cover
Assembly Hole
REFRIGERATOR INSTALLATION
LEVELING AND DOOR ALIGNMENT
Leveling
After installing, secure the product with the LEG
not to move left or right.
Your refrigerator has two front leveling screws—
one on the right and one on the left. If your
refrigerator seems unsteady or you want the
doors to close easier, adjust the refrigerator’s tilt
using the instructions below:
1. Plug the refrigerator’s power cord grounded
outlet. Move the refrigerator into its final
position.
To remove the base cover
1. Open the Freezer Drawer. (Drawer not
shown for clarity.)
2. Once drawer is open there is sufficient
clearance to remove screws on top of cover.
To replace base cover:
• Place cover into position and insert and
tighten screws.
2. Turn the leveling screw clockwise to raise that
side of the refrigerator or counterclockwise to
lower it. It may take several turns of the
leveling screw to adjust the tilt of the
refrigerator.
NOTE: Having someone push against the top
of the refrigerator takes some weight off the
leveling screws. This makes it easier to adjust
the screws.
3. Open both doors again and check to make
sure that they close easily. If not, tilt the
refrigerator slightly more to the rear by turning
both leveling screws clockwise. It may take
several more turns, and you should turn both
leveling screws the same amount.
4. Re-adjust if necessary.
5. Replace the base cover.
NOTE: Your new refrigerator is uniquely
designed with two fresh food doors. Either door
can be opened or closed independently of one
another. You may have to exert slight pressure
on doors to get them to close completely.
Door Alignment
If the space between your doors is uneven, follow
the instructions below to align the doors:
1. With one hand, lift up the door you want to
raise at middle hinge.
2. With other hand, use pliers to insert snap ring
as shown.
3. Insert additional snap rings until the doors are
aligned. (Three snap rings are provided with
unit.)
13
USING YOUR REFRIGERATOR
SETTING THE CONTROLS
• Your refrigerator has a control pad on the
dispenser that lets you regulate the temperature
in the freezer and refrigerator compartments.
• Initially set the REFRIGERATOR CONTROL at
3°C and the FREEZER CONTROL at –18°C.
Leave it at this setting for 24 hours (one day) to
stabilize. Then adjust the compartment
temperature as desired.
• Every time you touch the freezer temperature
adjust button, the temperature changes in a
circulating order of “-13” ’ “-14” ’ “-15” ’ “-16” ’
“-17” ’ “-18” ’ “-19” ’ “-20” ’ “-21” ’ “-13”.
• Every time you touch the refrigerator temperature
adjust button, the temperature changes in a
circulating order of
“0”’“8”’“7”’“6”’“5”’“4”’“3”’“2”’“1”’“0”.
CAUTION: The control display is operated by
touch. Excessive moisture on the display may
cause a malfunction. Please keep display clean
and dry.
NOTE: This is to prevent the unintended working
error when touching again. When 10 seconds has
passed since final touch, the existed display blinks
once and then the key starts to work by second
touch.
EXPRESS FRZ.
• When you touch the “EXPRESS FRZ.” button,
the graphic [ ] will light up in the display and it
continues for 24hours. It will automatically shut off
after 24hours have passed.
Or you can stop this function manually by
touching the button one more time.
• This function imcreases both icemaking and
freezing capabilities.
Dispenser
• You can select water, crushed ice, or
cubed ice by touching button as you
desire.
• There could be some dripping after
dispensing.
It is recommended to hold your cup for a
couple of seconds after dispensing.
NOTE : The dispenser is desinged not to
operate while either refrigerator door is left open.
Filter
• It displays in months the number of months left to
exchange the filter from the moment power is
connected to the refrigerator.
• If you have changed the filter after 6 months of
use or want to reset the filter display, press and
hold the Filter Reset Button 3 seconds or more
and the filter display will be initialized with a
buzzing sound.
NOTE : The average life of the filter is 6 months.
Alarm
• When the power is connected to the refrigerator,
door alarm is initially set OFF and door alarm
display will show . When you touch
button, the display will change to and door
alram function is now activated.
• When either refrigerator or the freezer door is left
open for more than 60 seconds, the alarm will
ding to let you know the door is open.
• When you close the door, the door alarm will stop
dinging.
• If you want to disable the door alarm function,
touch button then the door alarm display will
switched to .
Lock
• When the power is initially connected to the
refrigerator, Lock Function is Off.
• If you want to activate Lock Function to lock other
buttons, press and hold button for 3 seconds
or more. sign will be displayed and the Lock
Function is now enabled.
• No buttons except and dispenser button will
work while lock function is enabled.
• To disable the Lock Function, press and hold
button for 3 seconds or more.
ENSURING PROPER AIR CIRCULATION
Do not block air channels with any objects or food
for air circulation to prevent food loss due to the
lack of cooling air.
14
USING YOUR REFRIGERATOR
15
CAUTIONS
Throw away the first 20 ice cubes made, and the first 7 glass of dispensed water after
installation.
This is also recommended if the refrigerator has not been used for a long time.
Keep children away from the dispenser.
Children may play with or damage the controls.
Storing cans or other items in the ice bucket may damage
the icemaker.
Never use thin crystal glass or crockery to collect ice cubes.
Such glasses or containers may be broken.
Get ice cubes first into a glass before dispensing water.
Water may splash if it is done in opposite way..
Keep your hands and tools out of the ice room door and
dispenser chute..
You could break something or injure yourself.
Shake the ice bucket occasionally to level the ice in it.
Sometimes the ice piles up near the icemaker, causing the icemaker to misread the amount of ice
cubes and stop producing ice.
Never use narrow or deep glass.
Ice could be stuck inside dispenser chute and, thus the refrigerator could fail.
Keep the glass at a proper distance from dispenser chute.
A glass too close to the outlet may hinder ice from coming out.
Keep the ice room door closed tightly after opening it.
If the ice room door were not closed tightly, the cold air in the ice room would come into refrigerator
compartment and freeze food. This could cause the ice maker not to produce ice.
Close the freezer door until you hear the sound "flick".
When the door doesn't properly close, ice in the freezer could be
melt, or frost and icicle could be formed within the refrigerator.
Ice Bucket
Ice Room Door
USING YOUR REFRIGERATOR
HOW TO USE A NEW DOOR ICE BUCKET
The ice maker will stop producing ice when ice bucket is full. If you need more ice, please use the extra
ice bucket in freezer compartment so icemaker can keep producing ice.
How to remove the Door Ice Bucket.
16
How to remove the Door Ice Bucket.
1 . Grip the handle as shown in
the picture
2. Lift the lower part slightly. 3. Take the ice bucket out
slowly.
1 . Replace ice bucket by slightly slanting it to
avoid touching the ice maker.
* Avoid touching the automatic shut off arm when
replacing the ice bucket.
USING YOUR REFRIGERATOR
17
ADJUSTING CONTROL SETTINGS
Give the refrigerator time to cool down completely
before making final adjustments. It is best to wait
24 hours before doing this. The mid-settings
indicated in the previous section should be
correct for normal household refrigerator usage.
The controls are set correctly when milk or juice
is as cold as you like and when ice cream is firm.
The refrigerator control functions as the
thermostat for the entire appliance (refrigerator
and freezer sections). The higher the number
setting, the longer the compressor will run to
keep the temperature colder. The freezer control
adjusts the cold air flow from the freezer to the
refrigerator. Setting the freezer control to a lower
temperature keeps more cold air in the Freezer
compartment to make it colder.
If you need to adjust temperatures in the
refrigerator or freezer, start by adjusting the
refrigerator. Then wait 24 hours before checking
the freezer temperature. If it is too warm or too
cold, then adjust the freezer control.
Use the settings listed in the chart below as a
guide. Always remember to wait at least 24
hours between adjustments.
FOOD STORAGE GUIDE
Wrap or store food in the refrigerator in airtight
and moisture-proof material unless otherwise
noted. This prevents food odor and taste transfer
throughout the refrigerator. For dated products,
check date code to ensure freshness.
CONDITION/
REASON:
■ REFRIGERATOR section
too warm
– Door opened often
– Large amount of food
added
– Room temperature very
warm
■ FREEZER section too
warm/ice not made fast
enough
– Door opened often
– Large amount of food
added
– Very cold room
temperature (can’t cycle
often enough)
– Heavy ice usage
– Air vents blocked by items
■ REFRIGERATOR section
too cold
– Controls not set correctly
for your conditions
■ FREEZER section too
cold
– Controls not set correctly
for your conditions
RECOMMENDED
ADJUSTMENT:
Set
REFRIGERATOR
control to next
lower number,
wait 24 hours,
then re-check
Set FREEZER
control to next
lower number,
wait 24 hours,
then re-check
Move items out of
airstream
Set
REFRIGERATOR
control to next
higher number,
wait 24 hours,
then re-check
Set FREEZER
control to next
higher number,
wait 24 hours,
then re-check
Items
Butter or
margarine
Cheese
Milk
Eggs
Fruit
Leafy
vegetables
Vegetables
with skins
(carrots,
peppers)
Fish
Leftovers
How to
Keep opened butter in a
covered dish or closed
compartment. When storing an
extra supply, wrap in freezer
packaging and freeze.
Store in the original wrapping
until you are ready to use it.
Once opened, rewrap tightly in
plastic wrap or aluminum foil.
Wipe milk cartons. For best
storage, place milk on interior
shelf, not on door shelf.
Store in original carton or Egg
Box on interior shelf, not on
door shelf.
Wash, let dry, and store in
refrigerator in plastic bags or
in the crisper. Do not wash or
hull berries until you are ready
to use them. Sort and keep
berries in their original
container in a crisper, or store
in a sloosely closed paper bag
on a refrigerator shelf.
Remove store wrapping and
trim or tear off bruised and
discolored areas. Wash in cold
water and drain. Place in
plastic bag or plastic container
and store in crisper.
Place in plastic bags or plastic
container and store in crisper.
Use fresh fish and shellfish the
same day purchased.
Cover leftovers with plastic
wrap or aluminum foil. Plastic
containers with tight lids can
also be used.
STORING FROZEN FOOD
NOTE: For further information about preparing
food for freezing or food storage times, check a
freezer guide or a reliable cookbook.
Packaging
Successful freezing depends on correct
packaging. When you close and seal the
package, it must not allow air or moisture in or
out. If it does, you could have food odor and taste
transfer throughout the refrigerator and also dry
out frozen food.
Packaging recommendations:
• Rigid plastic containers with tight-fitting lids
• Straight-sided canning/freezing jars
• Heavy-duty aluminum foil
• Plastic-coated paper
• Non-permeable plastic wraps
• Specified freezer-grade self-sealing plastic bags
Follow package or container instructions for
proper freezing methods.
Do not use:
• Bread wrappers
• Non-polyethylene plastic containers
• Containers without tight lids
• Wax paper or wax-coated freezer wrap
• Thin, semi-permeable wrap
CAUTION: Do not keep beverage cans or
plastic food containers in the freezer
compartment. They may be break if it freezes.
Freezing
Your freezer will not quick-freeze any large
quantity of food. Do not put more unfrozen food
into the freezer than will freeze within 24 hours.
Leave enough space in the freezer for air to
circulate around packages. Be careful to leave
enough room at the front so the door can close
tightly.
Storage times will vary according to the quality
and type of food, the type of packaging or wrap
used (airtight and moisture-proof) and the storage
temperature. Ice crystals inside a sealed package
are normal. This simply means that moisture in
the food and air inside the package have
condensed, creating ice crystals.
NOTE: Allow hot foods to cool at room
temperature for 30 minutes, then package and
freeze. Cooling hot foods before freezing saves
energy.
REFRIGERATOR SECTION
WATER DISPENSER
Tray can be easily removed by pressing and
pulling it.
Tilt up the front of tray slightly and snap the ribs
into the holes to reinstall the tray.
WARNING: Do not throw your hands in the
water & ice opening. Doing so can result in
amputation or cuts.
USING YOUR REFRIGERATOR
18
Holes
Ribs
USING YOUR REFRIGERATOR
REFRIGERATOR SHELVES
The shelves in your refrigerator are adjustable to
meet your individual storage needs. Your model
may have glass or wire shelves.
Storing similar food items together in your
refrigerator and adjusting the shelves to fit
different heights of items will make finding the
exact item you want easier; it will also reduce the
amount of time the refrigerator door is open,
saving energy.
IMPORTANT: Do not clean glass shelves with
warm water when they are cold. Shelves may
break if exposed to sudden temperature changes
or impact, such as bumping. For your protection,
glass shelves are made with tempered glass,
which will shatter into small pebble-sized pieces.
NOTE: Glass shelves are heavy. Use special care
when removing them to avoid dropping them.
Adjusting Shelves
Remove shelves from the shipping position and
replace shelves in the position you want.
• To remove a shelf—Tilt up the front of the shelf
in the direction of (1) and lift it in the direction of
(2). Pull the shelf out.
• To replace a shelf—Tilt the front of the shelf up
and guide the shelf hooks into the slots at a
desired height. Then lower the front of the shelf
so that the hooks drop into the slots.
CAUTION: Make sure that shelves are level
from one side to the other. Failure to do so
may result in the shelf falling or spilling food.
Sliding Out Shelves
You can slide glass shelves in and out of your
refrigerator as follows.
• To slide the shelf out, carefully pull front of
shelf toward you.
• To slide shelf in, push shelf in until it stops.
BOTTLE HOLDER (Optional)
Bottles can be stored laterally with this bottle
holder. It can be attached to any shelf.
Bottle holder can be removed by pulling it straight
out and installed by placing it at the end of the
shelf you want and pushing it inward.
19
USING YOUR REFRIGERATOR
SNACK PAN
While holding the chef fresh with one hand, pull it
forward slightly.
OPTIBIN CRISPERS
The Optibin Crispers provide fresher-tasting fruit
and vegetables by letting you easily control
humidity inside the crisper. The Optibin Crispers
include: 1) a humidity control knob at the front of
the crisper cover and 2) a large lattice on the inner
surface of the cover to hold or release moisture.
CRISPER HUMIDITY CONTROL
You can control the amount of humidity in the
moisture-sealed crispers. Store vegetables or
fruits requiring more or less humidity in separate
crispers. Adjust the control to any setting
between and .
• lets moist air out of the crisper for best
storage of fruits.
• keeps moist air in the crisper for best
storage of fresh, leafy vegetables.
CAUTION: The glass shelf over the crisper is
not firmly secured. Be careful when tilting.
REMOVING CRISPER
uu
Crispers without rails
1. To remove, pull drawer out to full extension.
2. Lift the front of the crisper, then pull straight out.
3. To install, slightly tilt up the front and insert
drawer into frame and push back into place.
uu
Crispers with rails
To remove crisper:
1. Pull drawer out to full extension.
2. Lift the front of basket up and pull straight out.
To replace crisper:
1. Push rails to the back of the compartment.
2. Insert the back corner of the basket into frame.
3. Slightly tilt up the front and push back until it
snaps into place.
20
1
2
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
