Unbranded G6RC Offset Coupling Replacement Kit Installation guide

Unbranded
Brand
Unbranded
Model
G6RC Offset Coupling Replacement Kit
Type
Installation guide

Unbranded G6RC Offset Coupling Replacement Kit is a device that helps to replace the offset coupling in G6RC series furnaces. It comes with two 22.5° street elbows, one straight rubber coupling, and two hose clamps. The kit is easy to install and can be completed in 10 steps. It is important to note that the replacement of the offset coupling must be performed by a qualified installer, service agency, or the gas supplier. Improper installation can cause injury or property damage.

Here are some of the features and possible use cases of the Unbranded G6RC Offset Coupling Replacement Kit:

  • Replaces the offset coupling in G6RC series furnaces. The kit includes all the necessary components to replace the offset coupling, which is a critical part of the furnace's flue system. A faulty offset coupling can lead to leaks in the flue system, which can result in serious personal injury or death due to exposure to flue products, including carbon monoxide.

Unbranded G6RC Offset Coupling Replacement Kit is a device that helps to replace the offset coupling in G6RC series furnaces. It comes with two 22.5° street elbows, one straight rubber coupling, and two hose clamps. The kit is easy to install and can be completed in 10 steps. It is important to note that the replacement of the offset coupling must be performed by a qualified installer, service agency, or the gas supplier. Improper installation can cause injury or property damage.

Here are some of the features and possible use cases of the Unbranded G6RC Offset Coupling Replacement Kit:

  • Replaces the offset coupling in G6RC series furnaces. The kit includes all the necessary components to replace the offset coupling, which is a critical part of the furnace's flue system. A faulty offset coupling can lead to leaks in the flue system, which can result in serious personal injury or death due to exposure to flue products, including carbon monoxide.
REPLACING THE OFFSET COUPLING
WARNING:
Upon completion of the furnace installation,
carefully inspect the entire flue system both
inside and outside the furnace to assure it is
properly sealed. Leaks in the flue system can
result in serious personal injury or death due
to exposure of flue products, including carbon
monoxide.
1. Set the thermostat to the OFF position or to its lowest
setting.
2. Turn off all electrical power to the furnace.
3. Loosen the hose clamps holding the offset coupling to
the inducer and to the inline drain assembly and remove
the coupling. See Figure 1.
4. Slide the rubber coupling supplied with the kit over the
end of the inducer and secure it with one of the hose
clamps ensuring a leak free connection.
5. Slide one of the 22.5° PVC elbows into the other end
of the rubber coupling.
IMPORTANT NOTE:
Before permanently installing the components in
steps 6 & 7, it is recommended you dry-fit them first to
ensure proper fit and alignment with other vent pipes.
6. Dry fit the other PVC elbow to the installed elbow so
that the opening of the second elbow lines up with the
inline drain.
7. Dry fit second elbow to the inline drain assembly and
make sure that everything is properly aligned.
8. Permanently bond the elbows and the inline drain
assembly together using appropriate primer and cement.
NOTE: The cement must conform to ASTM Standard
D2564 for PVC. PVC primer must meet standard ASTM
F656. In Canada, cement, cleaners, or primers must
be certified as a system to ULC S636.
9. Secure the bottom elbow to the rubber coupling using the
remaining hose clamp ensuring a leak free connection.
10. Verify proper furnace operation by following the startup
procedures in the furnace installation instructions,
user’s manual and/or operating instruction label.
Offset Coupling Replacement Kit For G6RC Series Furnaces
KIT CONTENTS
QUANTITY DESCRIPTION
2 22.5° Street Elbows
1 Straight Rubber Coupling
2 Hose Clamps
FIRE OR EXPLOSION HAZARD
•Failure to follow safety warnings exactly
could result in serious injury or property
damage.
•Replacementoftheoffsetcouplingmustbe
performed by a qualified installer, service
agency or the gas supplier. Improper instal-
lation, alteration, service or maintenance can
cause injury or property damage.
WHAT TO DO IF YOU SMELL GAS
•Donottrytolightanyappliance.
•Donottouchanyelectricalswitch;donot
use any phone in your building.
•Leavethebuildingimmediately.
•Immediately call yourgas supplier froma
neighbor’s phone. Follow the gas supplier’s
instructions.
•Ifyoucannotreachyourgassupplier,call
the fire department.
WARNING:
INSTALLATION INSTRUCTIONS
Read these installation instructions thoroughly
before proceeding with the inducer replacement.
These instructions are primarily intended to assist
qualified individuals experienced in the proper vent
pipe installations of this appliance.
7092890 (NEW)
Hose Clamps
Coupling
Inducer
Inline Drain
Assembly
22.5° Street
Elbows (x2)
Figure 1. Coupling Installation
Specifications & illustrations subject to change without notice or incurring obligations (05/15).
O’Fallon, MO, © Nortek Global HVAC LLC 2015. All Rights Reserved.
  • Page 1 1
  • Page 2 2

Unbranded G6RC Offset Coupling Replacement Kit Installation guide

Unbranded
Brand
Unbranded
Model
G6RC Offset Coupling Replacement Kit
Type
Installation guide

Unbranded G6RC Offset Coupling Replacement Kit is a device that helps to replace the offset coupling in G6RC series furnaces. It comes with two 22.5° street elbows, one straight rubber coupling, and two hose clamps. The kit is easy to install and can be completed in 10 steps. It is important to note that the replacement of the offset coupling must be performed by a qualified installer, service agency, or the gas supplier. Improper installation can cause injury or property damage.

Here are some of the features and possible use cases of the Unbranded G6RC Offset Coupling Replacement Kit:

  • Replaces the offset coupling in G6RC series furnaces. The kit includes all the necessary components to replace the offset coupling, which is a critical part of the furnace's flue system. A faulty offset coupling can lead to leaks in the flue system, which can result in serious personal injury or death due to exposure to flue products, including carbon monoxide.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents