Bradford White 30A-6-3-201C-AA Installation guide

Brand: Bradford White

Model: 30A-6-3-201C-AA

Type: Installation guide

238-45837-00J REV 5/18

ASME COMMERCIAL ELECTRIC WATER HEATER

THE WARRANTY ON THIS WATER HEATER IS IN EFFECT ONLY WHEN

THE WATER HEATER IS INSTALLED AND OPERATED IN ACCORDANCE

WITH LOCAL CODES AND THESE INSTRUCTIONS. THE

MANUFACTURER OF THIS WATER HEATER WILL NOT BE LIABLE FOR

ANY DAMAGE RESULTING FROM FAILURE TO COMPLY WITH THESE

INSTRUCTIONS. READ THESE INSTRUCTIONS THOROUGHLY BEFORE

STARTING.

For your comfort, safety and convenience, it is recommended this

water heater be installed and serviced by a plumbing professional.

INSTALLATION & OPERATING

INSTRUCTION MANUAL

A Spanish language version of these instructions is available by

contacting the company listed on the rating plate.

La versión espãnola de estas instructiones se puede obtener al

escribible a la fábrica cuyo nombre aparece en la placa de

especificaciones.

CONGRATULATIONS!

You have just purchased one of the finest water heaters

on the market

today!

This installation, operation and instruction manual will explain in

detail the installation and maintenance of your new ASME Commercial

Electric Water Heater. We strongly recommend that you contact a

plumbing professional for the installation of this water heater.

We require that you carefully read this manual, as well as the

enclosed warranty, and refer to it when questions arise. If you have

any specific questions concerning your warranty, please consult the

plumbing professional from whom your water heater was purchased.

For your records we recommend that you write the model, serial

number and installation date of your water heater in the maintenance

section in the back of this manual.

This manual should be kept with the water heater.

TABLE OF CONTENTS

General Information ................................................... 3

Installation ............................................................... 4

Locating The Water Heater ............................................. 4

Water Connections ........................................................ 6

Electrical Connections .................................................... 13

Amperage Chart .......................................................... 14

GPH Recovery Capacities ............................................. 14

General Operation ..................................................... 15

Thermostat Adjustment .................................................. 15

Maintenance ............................................................. 16

Servicing Guide ......................................................... 19

GENERAL INFORMATION

This electric water heater’s design is certified by Underwriters

Laboratories (UL) and listed in accordance with UL 1453. C-UL listed in

accordance with Canadian National Standard C22.2, No. 110-M90.

This water heater must be installed in accordance with local codes. In

the absence of local codes, install this water heater in accordance with

the latest edition of the National Electrical Code.

The warranty for this water heater is in effect only when the water

heater is installed, adjusted, and operated in accordance with these

Installation and Operating Instructions. The manufacturer will not be

held liable for damage resulting from alteration and/or failure to comply

with these instructions.

This water heater has been designed and certified for the purpose of

heating potable water. The installation and use of this water heater for

any purpose other than the heating of potable water, may cause damage

to the water heater and create a hazardous condition and nullify the

warranty.

Do not use this appliance if any part has been submerged in water. The

plumbing professional responsible for the installation of this water heater

should be contacted to inspect the appliance and to replace any part of

the control system, including thermostat(s), which has been submerged

in water.

Make sure that the rating plate on the water heater is referenced for

certainty that the correct voltage is being supplied to the water heater.

CAUTION

Incorrect operation of this appliance may create a hazard to life and

property and will nullify the warranty.

DANGER

Do not store or use gasoline or other flammable, combustible, or

corrosive vapors and liquids in the vicinity of this water heater or any

other appliance.

General Information continued-

A sacrificial anode(s) is used to extend tank life. Removal of any anode,

except for inspection and/or replacement, will nullify the warranty. In areas

where water is unusually active, an odor may occur at the hot water faucet

due to a reaction between the sacrificial anode and impurities in the water. If

this should happen, an alternative anode(s) may be purchased from the

supplier that installed this water heater. This will minimize the odor while

protecting the tank. Additionally, the water heater should be flushed with

appropriate dissolvers to eliminate any bacteria.

WARNING

This product contains one or more chemicals known to the State of

California to cause cancer, birth defects, or reproductive harm.

INSTALLATION

Locating The Water Heater

This water heater MUST not be installed in any location where gasoline

or flammable vapors are likely to be present, unless the installation is

such to eliminate the probable ignition of gasoline or flammable

vapors.

The location where this water heater is to be installed is of utmost

importance. Before installing this water heater, consult the installation section

of these instructions. After reading these installation and operating

instructions, select a location for the water heater where the floor is level and

is easily accessible to a power supply and water connections. It is

recommended that the water heater be located near the center of greatest

hot water usage to prevent heat loss through the pipes. DO NOT locate the

water heater where water lines could be subjected to freezing

temperatures. Locate the water heater so that access panels, drain

valves, and clean-out openings are accessible.

IMPORTANT

Before proceeding, please inspect the water heater and its components for

possible damage. DO NOT install any damaged components. If damage is

evident, please contact the supplier where the water heater was purchased or

the manufacturer listed on the rating plate for replacement parts.

WARNING

Water heaters are heat producing appliances. To avoid damage or injury,

there shall be no materials stored against the water heater and proper care

shall be taken to avoid unnecessary contact (especially by children) with the

water heater. UNDER NO CIRCUMSTANCES SHALL FLAMMABLE

MATERIALS, SUCH AS GASOLINE OR PAINT THINNER BE USED OR

STORED IN THE VICINITY OF THIS WATER HEATER OR ANY

LOCATION FROM WHICH FUMES COULD REACH THE WATER

HEATER.

Locating The Water Heater continued-

Water heater corrosion and component failure can be caused by the

heating and breakdown of airborne chemical vapors. Examples of some

typical compounds that are potentially corrosive are: spray can

propellants, cleaning solvents, refrigerator and air conditioning

refrigerants, swimming pool chemicals, calcium or sodium chloride,

waxes and process chemicals. These materials are corrosive at very low

concentration levels with little or no odor to reveal their presence.

NOTE: DAMAGE TO THE WATER HEATER CAUSED BY EXPOSURE TO

CORROSIVE VAPORS IS NOT COVERED BY THE WARRANTY. DO NOT

OPERATE THE WATER HEATER IF EXPOSURE HAS OR WILL OCCUR.

DO NOT STORE ANY POTENTIALLY CORROSIVE COMPOUNDS IN THE

VICINITY OF THE WATER HEATER.

This water heater must be located in an area where leakage from the

tank, water line connections, and the combination temperature and

pressure relief valve will not result in damage to the area adjacent to the

water heater or to lower floors of the structure. When such locations

cannot be avoided, a suitable drain pan must be installed under the

water heater. The drain pan must have a minimum length and width of

at least 4 in. (10.2 cm) greater than the diameter of the water heater.

The drain pan, as described above, can be purchased from your

plumbing professional. The drain pan must be piped to an adequate

drain. The piping must be pitched for proper drainage.

CLEARANCES

1. Minimum clearance to combustible material is 0 inches for the Top,

Sides, Front, and Rear of this water heater. However, it is

recommended that at least 18 inches (45.7 cm) from the Top, and

24 inches (61 cm) from the Front. Clearance for servicing may be

reduced down to minimum clearance to combustible material, but

service time and effort may be greatly increased.

2. Increase distances to provide clearances for servicing.

This water heater MUST be installed indoors out of the wind and

weather.

To comply with NSF requirements this water heater is to be:

a) Sealed to the floor with sealant, in a smooth and easily cleanable

way, or

b) Installed with an optional leg kit that includes legs and/or extensions

that provide a minimum clearance of 6’’ beneath the water heater.

Note: For California installation this water heater must be braced,

anchored, or strapped to avoid falling or moving during an earthquake.

See instructions for correct installation procedures. Instructions may be

obtained from the DSA Headquarters Office: 1102 Q Street, Suite 5100,

Sacramento, CA 95811.

Water Connections

Note: Before proceeding with the installation, close the main water

supply valve.

After shutting the main water supply valve, open a faucet to relieve the

water line pressure in order to prevent water from leaking out of the

pipes while making the water connections to the water heater. After the

pressure has been relieved, close the faucet. The cold water inlet line

connects to the inlet nipple at the base of the water heater. The hot

water outlet line connects to the nipple on top of the water heater. The

fittings at the cold water inlet and hot water outlet are dielectric

waterway fittings with tapered male threads. Make the proper plumbing

connections between the water heater and the plumbing system in the

structure. Install a manual shut-off valve in the cold water supply line.

This water heater may be provided with an optional pressure and

temperature gauge. See Figure 1 for proper installation.

If this water heater is installed in a closed water supply system, such as

one having a back-flow preventer in the cold water supply, provisions

must be made to control thermal expansion. DO NOT operate this water

heater in a closed system without a provision for controlling thermal

expansion. Contact your water supplier or local plumbing inspector

regarding how thermal expansion can be controlled.

After installation of the water lines, open the main water supply valve

and fill the water heater. While the water heater is filling, open several

hot water faucets to allow air to escape from the water system. When a

steady stream of water flows through the faucets, close the faucets and

inspect all water connections for possible leaks. NEVER OPERATE THE

WATER HEATER WITHOUT FIRST BEING CERTAIN IT IS COMPLETELY

FILLED WITH WATER.

CAUTION

If sweat fittings are to be used, DO NOT apply heat to the nipples on

top of the water heater. Sweat the tubing to the adapter before fitting

the adapter to the water connections. It is imperative that heat is not

applied to the nipples containing a plastic liner.

IMPORTANT

FAILURE TO INSTALL AND MAINTAIN A NEW, LISTED

TEMPERATURE-PRESSURE RELIEF VALVE WILL RELEASE THE

MANUFACTURER FROM ANY CLAIM WHICH MIGHT RESULT FROM

EXCESSIVE TEMPERATURE AND PRESSURES.

Water Connections continued-

WARNING

For protection against excessive temperatures and pressure, install

temperature and pressure protective equipment required by local

codes, but not less than a combination temperature and pressure relief

valve certified by a nationally recognized testing laboratory that

maintains periodic inspection of production of listed equipment or

materials, as meeting the Requirements for Relief Valves and

Automatic Gas Shutoff Devices for Hot Water Supply Systems, ANSI

Z21.22, and the Standard CAN1-4.4 Temperature, Pressure,

Temperature and Pressure Relief Valves and Vacuum Relief Valves.

The combination temperature and pressure relief valve shall be marked

with a maximum set pressure, not to exceed the maximum working

pressure of the water heater. The combination temperature and

pressure relief valve shall also have an hourly rated temperature steam

BTU discharge capacity not less than the hourly input rating of the

water heater.

Install the combination temperature and pressure relief valve into the

opening on the water heater, which is provided for this purpose.

Note: Some models may already be equipped or supplied with a

combination temperature and pressure relief valves. Verify that this

combination temperature and pressure relief valve complies with local

codes. If the combination temperature and pressure relief valve does

not comply with local codes, replace it with one that does. Follow the

installation instructions provided on this page.

Install a discharge line so that water discharged from the combination

temperature and pressure relief valve will exit within six (6) inches

(15.3 cm) above, or any distance below the structural floor and at a

location where dischargers cannot contact any live electrical part. This

discharge line is to be installed complete drainage of both the

temperature and pressure relief valve and the discharge line can occur.

The discharge opening must not be subjected to blockage or freezing.

DO NOT thread, plug or cap the discharge line. It is recommended that

a minimum of four (4) inches (10.2 cm) be provided on the side of the

water heater for servicing and maintenance of the combination

temperature and pressure relief valve.

Do not place a valve between the combination temperature and

pressure relief valve and the tank.

Water Connections continued-

This water heater can deliver scalding temperature water at any faucet

in the system. Be careful whenever using hot water to avoid scalding

injury. Certain appliances, such as dishwashers and automatic clothes

washers, may require increased temperature water. By setting the

thermostat on this water heater to obtain the increased temperature

water required by these appliances, the potential for scald injury is

increased. To protect against injury, install an anti-scald tempering valve

in the water system. This valve will reduce the point of discharge water

temperature by mixing cold and hot water in branch supply lines. Anti-

sealed tempering valves can be obtained from your local plumbing

supplier. Please consult a plumbing professional.

WARNING

Hydrogen gas can be produced in the hot water system served by this

water heater when there has been no usage for a long period of time

(generally two weeks or more). Hydrogen gas is extremely flammable.

Therefore, to reduce the risk of injury under these conditions, it is

recommended that the hot water faucet be opened for several

minutes at the kitchen sink before using any electrical appliance

connected to the hot water system. If hydrogen is present, there will

probably be an unusual sound, such as air escaping through the pipe,

as the water begins to flow. There should be no smoking or open

flame near the faucet at the time it is open.

CAUTION

INCREASING THE THERMOSTAT SETTING ABOVE THE PRESET

TEMPERATURE MAY CAUSE SEVERE BURNS AND CONSUME

EXCESSIVE ENERGY. HOTTER WATER INCREASES THE RISK OF

SCALD INJURY.

Water Connections continued-

Figure 1



























Water Connections continued-

Figure 2A

(Dual Temperature System With Mixing Valve)

50A, 80A, 120A

Figure 2B

(Dual Temperature System With Mixing Valve)

6A, 12A, 20A, 30A, 40A

Water Connections continued-

Figure 3A

(Single Installation With Storage Tank Gravity Circulation)

50A, 80A, 120A

Figure 3B

(Single Installation With Storage Tank Gravity Circulation)

6A, 12A, 20A, 30A, 40A

Water Connections continued-

Figure 4A

(Dual Water Heater Installation)

50A, 80A, 120A

Figure 4B

(Dual Water Heater Installation)

6A, 12A, 20A, 30A, 40A

Electrical Connections

Before any electrical connections are attempted, be sure the water

heater is full of water and that the manual shut-off valve in the cold

water supply line is open. Heating elements, which have been energized

for a very short period of time, can be damaged (burned-out) if they are

not completely immersed in water. This warranty does not cover burned-

out heating elements. Check the rating plate and wiring diagram before

proceeding. This electric water heater was manufactured and wired in

accordance with the Underwriters Laboratories testing approvals

requirements. The temperature-limiting device is of the manual reset,

trip-free type and has been factory installed to interrupt all ungrounded

power supply conductors in the event of thermostat failure. The

plumbing supplier in your area ordered this water heater wired at the

factory to comply with existing area codes, but local utility codes may

require or allow other circuitry. Consult your local power company to

determine the correct electrical hook-up in order to meet local utility and

building codes and in order to obtain the most economical rates. All

electrical connections to elements, thermostats, contactors, fuses

(certain models), and transformer have been made at the factory. DO

NOT alter any of the internal wiring. Wiring connections may loosen

during shipment. Check all connections for tightness.

To make the wiring connections to a power supply, follow the steps

below.

A) Open the cover door of the control box.

B) Bring the power leads from an adequately fused disconnect switch

(not furnished with the water heater due to varying state and local

codes) and connect to the terminal block. Local ordinances and/or

utility company may require an increase in the gage size of the wiring

for conditions where long wiring lengths exist.

C) This water heater must be properly grounded. A ground lug is

provided within the electrical control box for connection to a properly

sized ground. (See wiring diagram for minimum required ground size.

The wiring diagram is located on the inside door of the control box)

D) Close the cover door of the control box.

Heating Elements

To replace heating elements, disconnect power to the water heater,

drain tank and replace element. To remove a heating element, use a

screw type element wrench (1 1/2’’ or 2 3/8’’) available from most

supply houses. Do not over-tighten the new element, as this will cause

distortion in the new element gasket. Once the element has been

replaced, follow the instructions ‘‘To Fill The Water Heater’’. It is

imperative that the water heater is full before power is restored to the

heating elements.

Amperage Chart

208V

240V

277V

380V

415V

480V

415V

Input

1Ø

3Ø

1Ø

3Ø

1Ø

3Ø

1Ø

3Ø

13.5

115

100

130

113

144

125

108

173

100

150

130

216

125

188

108

162

260

150

225

130

195

113

390

225

338

195

293

123

113

169

Water heaters with amperage draw of 120 AMPS or more require factory

installed internal fusing to comply with Underwriters Laboratories requirements.

GPH Recovery Capacities

Temperature Rise

Input

40°F

50°F

60°F

70°F

80°F

90°F

100°F

120°F

140°F

124

13.5

140

112

155

125

103

186

149

124

106

248

199

164

142

124

110

279

223

186

160

140

124

112

310

248

207

177

155

138

124

103

372

298

248

213

186

165

149

124

106

465

372

310

266

233

207

186

155

133

558

447

372

319

279

248

223

186

160

837

671

558

479

419

372

335

279

240

Multiply kW input by 3,412 to determine BTU input:

Example: 54kW x 3412 = 184,248 BTU’s

Recovery Computation Formula

GPH= (watts x 3.412) / (8.25 x °Temp. Rise)

GENERAL OPERATION

Before closing the switch to allow electric current to flow to the water

heater, make certain that the water heater is full of water and that the

cold water inlet valve is open. Complete failure of the heating elements

will result if they are not totally immersed in water at all times. When

the switch is closed, the operation of this electric water heater is

automatic. The temperature control knob located on the side on the

control box is factory preset to 120° F (49°C). Care must be taken

whenever using hot water to avoid scalding injury. Certain appliances

require high temperature hot water (such as dishwashers and automatic

clothes washers).

TO FILL THE WATER HEATER

1. Close the water heater drain valve by turning the knob clockwise.

2. Open the cold water supply shut-off valve.

3. Open several hot water faucets to allow air to escape from the

system.

4. When a steady stream of water flows from the faucets, the water

heater is filled. Close the faucets and check for water leaks at the

water heater drain valve, combination temperature and pressure

relief valve and the hot and cold water connections.

5. Reconnect power supply to water heater.

TO DRAIN THE WATER HEATER

Should it become necessary to completely drain the water heater, make

sure you follow the steps below:

1. Disconnect the power supply to the water heater. Consult the

plumbing professional or electric company in your area for service.

2. Close the cold water supply shut-off valve.

3. Open the drain valve on the water heater by turning the knob

counter-clockwise. The drain valve has threads on the end that will

allow connection of a standard hose coupling.

4. Open a hot water faucet to allow air to enter the system.

To refill the water heater, refer to ‘‘TO FILL THE WATER HEATER.’’

Thermostat Adjustment

To adjust the water temperature, locate the temperature control dial on

the right side of the control box. To increase the water temperature,

rotate the temperature control dial clockwise. To decrease the water

temperature, rotate the temperature control dial counterclockwise (see

Figure 5). The thermostat(s) or temperature control dial has been factory

preset to approximately 120° F (49°C).

CAUTION

Scalding may occur within five (5) seconds at a temperature setting

of 140°F (60°C).

Thermostat adjustment continued-

Figure 5

MAINTENANCE

Shut off the electric power whenever the water supply to the water

heater is off. Shut off the electric power and water supply, drain the

water heater completely to prevent freezing whenever the building is left

unoccupied during the cold weather months. In order to insure efficient

operation and long tank life, drain the water heater at least once a

month through the drain valve until the water runs clear. Failure to do

this may result in noisy operation and lime and sediment buildup in the

bottom of the tank. Check the temperature-pressure relief valve to

insure that the valve has not become encrusted with lime. Lift the lever

at the top of the valve several times until the valve seats properly

without leaking and operates freely.

DANGER

Hotter water increases the risk of scald injury. Scalding may occur

within five (5) seconds at a temperature setting of 140°F (60°C). To

protect against hot water injury, install an anti-scald tempering valve in

the water system. This valve will reduce point of discharge water

temperatures by mixing cold and hot water in branch water lines. A

licensed plumbing professional or local plumbing authority should be

consulted.

Note: This water heater is equipped with an energy cut out device to

prevent overheating. Should overheating occur, turn off the electrical

supply to the water heater and contact a qualified service technician.

IMPORTANT

The water heater should be inspected at a minimum of annually by a

qualified service technician for damaged components. DO NOT

operate this water heater if any part is found damaged.

Maintenance continued-

The following maintenance should be performed by a qualified service

technician at the minimum periodic intervals suggested below. In some

installations, the maintenance interval may be more frequent depending

on the amount of use and the operating conditions of the water heater.

Regular inspection and maintenance of the water heater will help to

insure safe and reliable operation.

1. Annually, check the operation of the thermostat(s).

2. Bi-annually, check the seal around the heating elements for leaks. If

there is any sign of leaking, disconnect the power supply to the water

heater and contact the plumbing professional that installed this water

heater or a qualified service technician.

3. At least once a year, check the combination temperature and

pressure relief valve to insure that the valve has not become

encrusted with lime. Lift the lever at the top of the temperature-

pressure relief valve several times until the valve seats properly

without leaking and operates freely.

4. If the combination temperature and pressure relief valve on the

appliance discharges periodically, this may be due to thermal

expansion in a closed water supply system. Contact the water

supplier or local plumbing inspector on how to correct this situation.

Do not plug the combination temperature and pressure relief valve

outlet for any reason.

5. Monthly, drain the water heater through the drain valve until the

water runs clear to remove silt and sediment.

6. A sacrificial anode rod has been installed to extend tank life. The anode

rod should be inspected periodically (every 2 years) and replaced when

necessary to prolong tank life. Water conditions in your area will influence

the time interval for inspection and replacement of the anode rod. Contact

the plumbing professional who installed the water heater or the

manufacturer listed on the rating plate for anode replacement information.

The use of a water softener may increase the speed of anode

consumption. More frequent inspection of the anode is needed when

using softened (or phosphate treated) water.

WARNING

When lifting lever of temperature-pressure relief valve, hot water will

be released under pressure. Be certain that any released water does

not result in bodily injury or property damage.

WARNING! THIS WATER MAY BE HOT.

Maintenance continued-

7. If this water heater is equipped with fuses, before removing any fuse,

disconnect the all power to the water heater. Open the control box

door and replace fuses according to the size indicated on the wiring

diagram affixed to the inside of the control box door.

Contact your local plumbing supplier or plumbing professional for

replacement parts or contact the company at the address displayed on

the rating plate of the water heater.

For faster and better service, please provide the part name, model, and

serial number(s) of the water heater(s) when ordering parts.

READ THE WARRANTY FOR A FULL EXPLANATION OF THE LENGTH

OF TIME THAT PARTS AND THE WATER HEATER ARE WARRANTED.

Complete the following information and retain for future reference:

Model No:_____________________________________________________

Serial No:______________________________________________________

Service Phone

Days: ______________________Nights:_____________________________

Address:______________________________________________________

Supplier:______________________________________________________

Supplier Phone No:______________________________________________

CAUTION

FOR YOUR SAFETY, DO NOT ATTEMPT TO REPAIR THERMOSTAT(S),

HEATING ELEMENTS, OR ELECTRICAL WIRING. REFER SUCH REPAIRS

TO A QUALIFIED SERVICE TECHNICIAN.

Manufactured under one or more of the following U.S. Patents: 5,277,171;

5,341,770; 5,372,185; 5,485,879; 5,574,822; 5,596,952; 5,660,165;

5,682,666; 5,761,379; 5,943,984; 5,954,492; 5,988,117; 6,056,542;

6,142,216; 6,442,178; 6,684,821; 6,935,280; 7,063,132; 7,063,133;

7,007,748; 7,270,087; 7,334,419; 7,337,517; 7,409,925; 7,458,341;

7,559,293; 7,621,238; 7,634,976; 7,650,859; 7,665,210; 7,665,211;

7,699,026; 7,866,168; 7,900,589; 7,971,560; 7,992,526 8,082,888;

8,146,772; Other U.S. and Foreign patent applications pending. Current

Canadian Patents: 2,092,105; 2,107,012; 2,108,186; 2,112,515; 2,143,031;

2,239,007; 2,262,174; 2,314,845; 2,409,271; 2,476,685; 2,504,824;

2,548,958

SERVICING GUIDE

This ‘‘Servicing Guide‘‘ section of this Installation and Operation

Installation manual is provided for the purpose of improving the

effectiveness and the efficiency of servicing this water heater. This

information is intended to assist qualified service personnel. Servicing of

this water heater may require knowledge of electrical testing

instruments. If you are unfamiliar or unsure of the electrical circuits or

the testing instruments, consult a qualified electrician.

This section of these Installation and Operation Instructions is not

intended for use as a troubleshooting guide. For troubleshooting

instructions please contact the supplier from whom this water heater

was purchased or the manufacturer listed on the rating plate.

This water heater has two distinct electrical systems. One system

connects the electrical power to the heating elements, while the other

system controls the water heater operation. The electrical contactors

interconnect these two systems. In order to clearly illustrate the

electrical circuits, two wiring diagrams are provided. These diagrams are

labeled as the ‘‘Power Circuit Wiring Diagram’’ and the ‘‘Control Circuit

Wiring Diagram’’ and they are attached to the surface of the panels

inside the water heater control cabinet.

Control Circuit Description:

This description will explain certain aspects of the Control Circuit. The

control circuit operates with 120VAC electrical service. This voltage is

provided by the multi-tap transformer which has the primary coil

connected to the field wiring that is serving the water heater. The

Transformer, the Water Heater Thermostat, the Hi-Limit Temperature

Control, and the Contactor Coil are always included in the Control

Circuit.

Referring to the ‘‘Control Circuit Wiring Diagram‘‘, the contactor coil is

energized when the Thermostat senses a need for heating. Electrical

current to the contactor coil will be interrupted when the water

temperature is sufficient to satisfy the temperature limits of the either

the Thermostat or the Hi-Limit Control. The Hi-Limit Control is provided

with manual reset buttons.

Servicing Guide continued-

Certain other control components are available as ‘‘Optional‘‘. When

these optional components are installed with the water heater, the

control circuit wiring diagram accordingly will include these components.

The optional equipment available from the manufacturer includes the

following:

• High Water Pressure Switch

• Low Water Pressure Switch

• Low Water Level Switch

• Alarm Horn

• Heating Element Sequencers

• Electrical Door Lock

Optional Components

High and Low Water Pressure Controls

These controls interrupt the electrical current to the contactor coil when

the pressure settings are exceeded. The operation and setting of these

controls are described in the manual provided by the control

manufacturer. This manual is included with the water heater Installation

and Operating Instruction manual provided by the manufacturer.

The pressure settings for these controls are adjustable. These controls

are specified for use when the installation has unique pressure

requirements that must be safeguarded. Therefore, before adjusting the

pressure values, it is recommended that you consult the person

responsible for the facility that the water heater is servicing.

The electrical connections are referenced in the Control Circuit Wiring

Diagram and in the pressure control manual provided by the control

manufacturer. Refer to these instructions when servicing the controls.

Page is loading ...

Bradford White 30A-6-3-201C-AA Installation guide

Brand: Bradford White

Model: 30A-6-3-201C-AA

Type: Installation guide

Download PDF

report

in other languages

polski: Bradford White 30A-6-3-201C-AA Instrukcja instalacji

Bradford White 30A-6-3-201C-AA Installation guide

Bradford White 30A-6-3-201C-AA Installation guide

in other languages

Related papers

Other documents