Cumberland PowerTrak Cool Side Delay Switch Owner's manual

Brand: Cumberland

Model: PowerTrak Cool Side Delay Switch

Type: Owner's manual

POWERTRAK

COOL SIDE DELAY SWITCH INSTALLATION

HIRED-HAND, INC.  1733 Co Rd 68  Bremen, AL 35033  Phone 1-800-642-0123  Fax 205-287-2000

Cool Side Delay Switch Installation 4801-0120 Rev 1/15 Page 1

Tools Required: Drill with 3/16" bit

3/4" Wrench

1/4" Allen Wrench

Crimping Tool

To Set Switch Position:

Manually raise or lower curtains to desired height.

Place template over side even with center of load block

(as shown below at left), then follow the instructions for

installation.

When installation is complete, manually raise and lower

curtain past the switch slowly to be sure that the switch

operates without binding.

Attach switch and bracket using

the two nuts and bolts provided.

Replace existing setscrews

with new longer setscrews.

Place bracket on new setscrews, and

secure with nuts. Be sure the bracket

can slide from side to side. Attach one end of tensioning

spring to bracket as shown,

and the other end around the

grease fitting.

Note: Nuts should not be

completely tightened so

that the bracket may slide

back and forth freely.

Lay template over side of

PowerTrak at desired height.

Mark and Drill holes. Notice!

Switch must be installed on machine

operating the curtain you want to open first.

(Typically the south side.)

Purpose of Equipment:

To create a Cool Side Delay by stopping the north side

machine from operating until the south side machine

hits a rocker switch set at a certain height.

Warning!

Disconnect all power sources to PowerTrak before

attempting to install the Auxiliary Switch. Electric Shock

may result.

* Note: For Serial Numbers 20825 and higher(DOM 3/4/96), you must add two 1/2 inch washers to

the setscrews between bracket and load nut.

Cumberland. 1004 E. Illinois St. Assumption, IL 62510 Phone 1-217-226-4421 Fax 1-217-226-4420

HIRED-HAND, INC.  1733 Co Rd 68  Bremen, AL 35033  Phone 1-800-642-0123  Fax 205-287-2000

Cool Side Delay Switch Installation 4801-0120 Page 2

POWERTRAK

COOL SIDE DELAY SWITCH INSTALLATION (Continued)

For 4, 5,or 6 foot PowerTrak machines only:

Replace the brace across the center front of the

machine. This brace is held in place by four bolts.

Use the original bolts to install the new brace.

Wiring the two PowerTrak machines, to operate with a

cool side delay requires that a wire connects the power

supply of the north side machine with the limit switch

installed on the south machine.

Wiring the machines requires breaking the orange wire

from the north side machine's limit switch harness, and

connecting a wire that runs through the cool delay

switch of the south side machine.

This orange wire on the north side machine is located

at the bottom right of the macine next to the motor

when looking through the open door. The wire

connects to the limit switch on top center of the

assembly. Run your wire from here to the cool delay

switch on the other machine as shown below.

All wiring must be performed in

accordance with all National and Local

Electric Codes. Installation by qualified

electrician recommended.

Open

Brown

Purple

Green

Blue

White

Orange

Lt. Blue

Auxilliary

Primary

Safety

Ground

Pull orange wire off of the

COM connection of the

above limit switch. Then

connect the switch in

between the orange wire

and the terminal where the

orange wire was originally

connected .

North (Delayed) Machine

South Machine

Cumberland. 1004 E. Illinois St. Assumption, IL 62510 Phone 1-217-226-4421 Fax 1-217-226-4420

Cumberland PowerTrak Cool Side Delay Switch Owner's manual

Cumberland PowerTrak Cool Side Delay Switch Owner's manual

Cumberland PowerTrak Cool Side Delay Switch Owner's manual

Related papers

Other documents