American Standard Jasmine Amarilis 3808.101 User manual
- Category
- Sanitary ware
- Type
- User manual
American Standard Jasmine Amarilis 3808.101 is a Centerset Lavatory Faucet with Speed Connect™ Drain. It is certified to comply with ANSI A112.18.1 standard. It features a single hole installation and can be installed with or without an escutcheon plate. The faucet has a decorative ring and comes with a Speed Connect™ Drain, which installs in less time and never needs adjustment. The drain is guaranteed to seal properly the first time, every time.
American Standard Jasmine Amarilis 3808.101 is a Centerset Lavatory Faucet with Speed Connect™ Drain. It is certified to comply with ANSI A112.18.1 standard. It features a single hole installation and can be installed with or without an escutcheon plate. The faucet has a decorative ring and comes with a Speed Connect™ Drain, which installs in less time and never needs adjustment. The drain is guaranteed to seal properly the first time, every time.
51314 Rev.1.3
Certified to comply with ANSI A112.18.1
Installation
Instructions
Centerset Lavatory Faucet with
Speed Connect™ Drain
Adjustable Wrench Screwdriver Channel Locks
Recommended tools
1
1
INSTALL FAUCET
Fig. B.
Fig. A.
3808.101
INSTALLATION WITH
ESCUTCHEON PLATE
SINGLE HOLE
INSTALLATION
1
For single hole installation. Fig. A.
Make sure that O-RING (1) is installed into base of FAUCET (2).
For installation with DECORATIVE RING (3) (single hole installation) feed faucet
SUPPLIES (4) and CABLE CONNECTOR (5) through sink or mounting surface hole.
For installation with ESCUTCHEON PLATE (6) (for 3 hole, 4" centers installation)
use the following steps:
Fig. B.
From below, push GASKET (7) and RETAINER PLATE (8)
over STUD (9) and secure with NUT (10) Before final
tightening, adjust faucet so that it is centered over
mounting hole.
Feed faucet tubes through O-RING (1) supplied with
ESCUTCHEON PLATE (6) and through the hole in the
ESCUTCHEON (6) and through SINK or DECK.
Unscrew and remove DECORATIVE RING (3) from FAUCET BODY (2).
Apply putty to underside of ESCUTCHEON PLATE (6) and
place over mounting holes.
5
7
8
5
10
4
4
1
1
6
2
2
7
8
10
3
3
9
9
PUTTY
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Speed Connect™ Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
Turn off water at
main supply.
CAUTION
51314 Rev.1.3
DOWN
WHITE FOAM
GASKET
NOT VISIBLE
DRAIN
FLANGE
Fig. A. Fig. B.
1
Thread FLANGE (1) counter-clockwise and
remove FLANGE (1) and FOAM GASKET (2)
from drain body.
Fig. A.
Thread LOCKNUT (3) clock-wise to bottom of
drain body. Push GASKET (4) down against
LOCKNUT (3).
Fig. B.
POP-UP DRAIN
Tighten TAILPIECE (4) on DRAIN BODY before
installing DRAIN BODY.
Fig. B.
6
2
4
3
2
TIGHTEN LOCKNUT
1
REMOVE FLANGE
Remove CLEAR PLASTIC COVER (1).
Remove CARDBOARD SPACER (2) from under
DRAIN POP-UP (3).
2
2
3
3
1
1
Tighten LOCKNUT (1) firmly with Adjustable
Wrench or Channel Locks.
INSTALL DRAIN FROM
BELOW FIXTURE
5
From under side of SINK
install DRAIN BODY (1) up
through drain outlet.
Note: No plumber’s putty
or caulk is required.
The CABLE ATTACHMENT
POINT (2) must face towards
the rear of the SINK.
Install FOAM GASKET (3)
and FLANGE (4) onto drain
body from above SINK and
tighten FLANGE (4) firmly.
4
Fig. A. Fig. B.
Fig. A. Fig. B.
POP-UP KNOB (1) must be fully down. Fig. B.
FLANGE GASKET AND POP-UP KNOB
Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET (3) is fully compressed
and not visible. Fig. A.
DRAIN
BODY
4
2
DRAIN
OUTLET
1
3
4
REAR
OF SINK
51314 Rev.1.3
CHECK OPERATION OF POP-UP
8
MAKE WATER SUPPLY AND WASTE CONNECTIONS
9
Thread CABLE CONNECTOR (1) clockwise
onto DRAIN BODY CONNECTION (2) and
hand tighten. Fig. A.
Your new POP-UP DRAIN installation is
now complete. Fig. B.
Note: Tailpeice on pop-up drain is 1-1/4” O.D.
Fig. B.
Fig. A.
ATTACH CABLE CONNECTOR
7
2
1
Fig. B.
1-1/4” O.D.
3
Operate LIFT KNOB (1) to verify that STOPPER (2) opens and
closes.
Note: If STOPPER (2) does not open and close properly then
refer to the “troubleshooting section” of these instructions.
1
APPROX. 20"
2
COLD
HOT
3/8" COMPRESSION
RED
BAND
BLUE
BAND
Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies.
Connection on fitting supplies are 3/8" compression. Connect
left SUPPLY (1) to Hot (Marked with a Red Band) and right supply
to COLD (2) wall supply.
Faucet supplies are 20" long from faucet base.
Note: If additional supply length is required, installer must
purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are to long, loop as
illustrated to avoid kinking.
Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to
waste outlet.
2
1
51314 Rev.1.3
2
1
SERVICE
TEST INSTALLED FITTING
With HANDLE (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
Remove AERATOR (3).
Operate HANDLE (1) to flush water lines thoroughly.
Replace AERATOR (3).
5
2
CHECK DRAIN CONNECTIONS
Operate POP-UP KNOB (4) and fill lavatory with water.
Check that DRAIN STOPPER (5) makes a good seal
and retains water in SINK. If DRAIN STOPPER (5)
does not seal properly, please refer to Troubleshooting
section in these instructions.
Release POP-UP KNOB (4) down and check all drain
connections and "P" trap for leaks. Tighten
if necessary.
12
11
10
“P” TRAP
WASTE
OUTLET
1
5
2
3
4
3
4
IF FAUCET DRIPS
4
Remove HANDLE (1), CAP (2) CARTRIDGE
SCREWS (3) RETAINER (4) and CARTRIDGE (5).
Clean inlets on CARTRIDGE (5).
Reassemble CARTRIDGE (5), RETAINER (4)
alternately tightening SCREWS (3), CAP (2)
and HANDLE (1). Check flow.
If faucet drips, operate handle several times from
"off" to "on". Do not apply excessive force.
Clogged CARTRIDGE (5) inlets may cause reduced
flow in "full on" hot or cold. To clean inlets, first
turn off water supply, then:
ADJUSTMENT WHEN
WATER IS TOO HOT
ADJUSTMENT WHEN
WATER IS TOO COLD
PRY RED RING FORWARD
AND ROTATE COUNTER-
CLOCKWISE ONE CLICK
PRY RED RING FORWARD
AND ROTATE CLOCKWISE
POINTER ON
HOT LIMIT STOP
"A"
"A"
"B"
"B"
RED RING HOT
LIMIT SAFETY
STOP
0
1
2
3
4
5
By restricting handle rotation and limiting the amount of hot
water allowed to mix with the cold, the HOT LIMIT SAFETY
STOP reduces risk of accidental scalding. To set the maximum
hot water temperature of your faucets, all you need
to do is adjust the setting on the HOT LIMIT SAFETY STOP.
Remove necessary trim parts. Use a flat blade screwdriver or
pull forward with your fingers to rotate red HOT LIMIT SAFETY
STOP. Follow Step "A" or "B" to adjust max./min. discharge
temperature. "0" being the hottest to "7" the coldest
temperature setting.
HOT LIMIT SAFETY STOP
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
-
1
-
2
-
3
-
4
American Standard Jasmine Amarilis 3808.101 User manual
- Category
- Sanitary ware
- Type
- User manual
American Standard Jasmine Amarilis 3808.101 is a Centerset Lavatory Faucet with Speed Connect™ Drain. It is certified to comply with ANSI A112.18.1 standard. It features a single hole installation and can be installed with or without an escutcheon plate. The faucet has a decorative ring and comes with a Speed Connect™ Drain, which installs in less time and never needs adjustment. The drain is guaranteed to seal properly the first time, every time.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
American Standard 7430.152.295 Installation guide
-
-
American Standard 4205.000.F15.002 User manual
-
-
-
American Standard 1480.150.002 Installation guide
-
-
-
American Standard 7420.101.295 Installation guide
-