Quikrete 691703 Installation guide

Quikrete
Brand
Quikrete
Model
691703
Type
Installation guide

This manual is also suitable for

Quikrete 691703: is a concrete expansion joint designed for use in all standard concrete construction, including highways, runways, parking garages, driveways, sidewalks, and floor slabs. It can also be used as a buffer between dissimilar materials such as columns, manhole covers, and adjacent constructions.

Here are some of the key capabilities of Quikrete 691703:

  • Made from a high-quality, closed-cell polyethylene foam, it is lightweight, non-absorbent, and will not break or crack when used around curves or columns.

  • Easy to cut and handle on the job site, it can be attached to adjacent materials using polyurethane construction adhesive, nails, or staples before pouring new concrete.

Quikrete 691703: is a concrete expansion joint designed for use in all standard concrete construction, including highways, runways, parking garages, driveways, sidewalks, and floor slabs. It can also be used as a buffer between dissimilar materials such as columns, manhole covers, and adjacent constructions.

Here are some of the key capabilities of Quikrete 691703:

  • Made from a high-quality, closed-cell polyethylene foam, it is lightweight, non-absorbent, and will not break or crack when used around curves or columns.

  • Easy to cut and handle on the job site, it can be attached to adjacent materials using polyurethane construction adhesive, nails, or staples before pouring new concrete.

C
C
C
O
O
O
N
N
N
C
C
C
R
R
R
E
E
E
T
T
T
E
E
E
E
E
E
X
X
X
P
P
P
A
A
A
N
N
N
S
S
S
I
I
I
O
O
O
N
N
N
J
J
J
O
O
O
I
I
I
N
N
N
T
T
T
P
P
P
R
R
R
O
O
O
D
D
D
U
U
U
C
C
C
T
T
T
N
N
N
O
O
O
.
.
.
6
6
6
9
9
9
1
1
1
7
7
7
-
-
-
0
0
0
5
5
5
PRODUCT USE
QUIKRETE
®
Concrete Expansion Joint can be used in all standard
concrete construction, such as highways, runways, parking garages,
driveways, sidewalks, and floor slabs. Concrete Expansion Joint can
also be used as a buffer between dissimilar materials such as columns,
manhole covers, and adjacent constructions. Meets ASTM D 1752* and
D 4819 Type II.
FEATURES
• Extruded from a high quality closed-cell polyethylene foam
• Will not break or crack when used around curves or columns
• Approximately 10 times lighter than traditional expansion joints
• Will not rot over time due to the near-zero water absorption
• Easy to cut and handle on the jobsite
SIZES
• QUIKRETE
®
Concrete Expansion Joint – 50’ rolls (15.2 M), 4” (100
mm) high.
TECHNICAL DATA
APPLICABLE STANDARDS
ASTM International
• ASTM D545 Test Methods for Preformed Expansion Joint Fillers for
Concrete Construction (Nonextruding and Resilient Types)
•ASTM D3575 Test Methods for Flexible Cellular Materials Made from
Olefin Polymers
• ASTM D1752 Specification for Preformed Sponge Rubber Cork and
Recycled PVC Expansion Joint Fillers for Concrete Paving and Structural
Construction (*With the compressive requirement of Section 5.3 modified
to 10 psi minimum and 25 psi maximum due to the material type)
• ASTM D4819 Specification for Flexible Cellular Materials Made From
Polyolefin Plastics
QUIKRETE
®
Concrete Expansion Joint meets the requirements of ASTM
standards D4819 Type II (Suffixes D4, B5, T
1
3, T
2
4, G2, W1, L1).
Typical physical properties, when tested with the appropriate ASTM
standard, are shown in Table 1.
INSTALLATION
Unroll expansion material and cut to needed length. Attach to
adjacent material (brick, block, existing concrete, etc.) using
QUIKRETE
®
Polyurethane Construction Adhesive (#9902-10), nails or
staples before pouring new concrete. The top of the expansion joint
should be at the same level as the new concrete being placed. Pour
concrete mix and finish.
Note: The expansion joint comes with a perforated tear off strip
called a ‘zip cap’. The ‘zip cap’ design allows the top of the
expansion joint to be removed to provide space for a caulk bead. If
caulking is not desired, install the expansion joint with the ‘zip cap’ on
the bottom.
TABLE 1 TYPICAL PHYSICAL PROPERTIES
Recovery, ASTM D 545 98.6%
Extrusion, ASTM D 545 0.16” (4 mm)
Compressive Strength, ASTM D545
Vertical Direction, Suffix D @ 50% 12.3 psi (84 kPa)
Compression Set, ASTM D 3575 (Suffix B) 16%
Tensile Stress, ASTM D 3575 44 psi (300 kPa)
Suffix T MD / CMD 26 psi (180 kPa)
Elongation, ASTM D 3575 79%
Suffix T MD / CMD 65%
Tear Resistance, ASTM D 3575 10 lb/in (0.18 kg/mm)
Suffix G MD / CMD 15 lb/in (0.27 kg/mm)
Density Range, ASTM D 3575 1.7 lb/ft3 (nominal)
Water Abs., ASTM D 3575 (Suffix L) <0.1 lb/ft2 (<0.49 kg/m2)
WARRANTY
The QUIKRETE® Companies warrant this product to be of
merchantable quality when used or applied in accordance with the
instructions herein. The product is not warranted as suitable for any
purpose or use other than the general purpose for which it is
intended. Liability under this warranty is limited to the replacement of
its product (as purchased) found to be defective, or at the shipping
PRODUCT DESCRIPTION
QUIKRETE
®
Concrete Expansion Joint is a soft, compressible foam insert for expansion
and isolation joints in concrete construction.
Common Work Results
for Concrete 03 05 00
DIVISION 3
companies’ option, to refund the purchase price. In the event of a claim
under this warranty, notice must be given to The QUIKRETE®
Companies in writing. This limited warranty is issued and accepted in lieu
of all other express warranties and expressly excludes liability for
consequential damages.
The QUIKRETE® Companies
One Securities Centre
3490 Piedmont Rd., NE, Suite 1300 Atlanta, GA 30305
(404) 634-9100 • Fax: (404) 842-1425
* Refer to www.quikrete.com for the most current technical data, MSDS, and guide specifications
  • Page 1 1
  • Page 2 2

Quikrete 691703 Installation guide

Quikrete
Brand
Quikrete
Model
691703
Type
Installation guide
This manual is also suitable for

Quikrete 691703: is a concrete expansion joint designed for use in all standard concrete construction, including highways, runways, parking garages, driveways, sidewalks, and floor slabs. It can also be used as a buffer between dissimilar materials such as columns, manhole covers, and adjacent constructions.

Here are some of the key capabilities of Quikrete 691703:

  • Made from a high-quality, closed-cell polyethylene foam, it is lightweight, non-absorbent, and will not break or crack when used around curves or columns.

  • Easy to cut and handle on the job site, it can be attached to adjacent materials using polyurethane construction adhesive, nails, or staples before pouring new concrete.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents