Panamax P360-8 User manual

Brand: Panamax

Model: P360-8

Type: User manual

Instruction

Manual

for the

P360-8

This Package Includes:

(1) POWER360 Eight Outlet Surge Protector

(2) Modular USB charging stations

(2) 6’ micro-USB to USB cables

(to connect charging station to base unit)

(2) Rubber feet for charging modules

(1) User manual

POWER360 Features

8 AC Outlets

8 surge protected AC outlets.

2 Modular Dual-Port USB chargers

Each Charging Station can charge up to two

devices simultaneously (2.1A capacity).

Protect or Disconnect

Keeps electronics safe from power spikes by

disconnecting load in a catastrophic event.

SmartGuard

Protects against brownouts and dangerous

over-voltage conditions. Disconnects the

power when the incoming voltage falls below

95 Volts or rises above 140 Volts. Reconnects

when the voltage returns to a safe level.

Circle of Protection

LED indicator monitors the outlet wiring,

voltage and protection status.

Coax and Telco Protection

Protects from surges on coax and telephone

signal lines, while maintaining full bandwidth

for high denition video and high speed

internet cable/DSL connections.

Lifetime Warranty

Limited lifetime product warranty

plus $500,000 connected equipment

protection policy.

Características de POWER360

8 enchufes de corriente alterna

8 enchufes de corriente alterna protegidos

contra sobretensión.

2 cargadoresUSBmodulares de dos

puertos

Cada estación de carga puede cargar hasta dos

dispositivos al mismo tiempo (capacidad 2.1A).

Tecnología de protección

Protege los productos electrónicos de picos

de energía al desconectarlos en caso de que se

produzcan incidentes.

Protección inteligente

Protege contra caídas de tensión y condiciones

peligrosas de sobretensión. Desconecta la corriente

cuando la tensión entrante cae por debajo de los

95 voltios o sube por encima de los 140 voltios.

Se reconecta cuando la tensión vuelve a un nivel

seguro.

Círculo de protección

El indicador LED reeja el estado del cableado de

los enchufes, el voltaje y la protección.

Coaxial y Protección Telco

Protege de sobretensiones en líneas coaxiales y

de señal de teléfono, manteniendo un ancho de

banda completo para video de alta denición y

las conexiones de cable/DSL de alta velocidad de

Internet.

Garantía de por vida

Garantía de producto limitada de por vida, más

políticade protección de 500 000$ para equipos

conectados.

POWER360 Caractéristiques

8 prises AC

8 Protecteurs de surtensions pour prises AC

2 Chargeurs modulaires à double ports

USB

Chaque station de chargement peut charger jusqu’à

deux appareils simultanément (capacité de 2,1 A).

Protéger ou Déconnecter

Protège votre équipement électronique en le

déconnectant en cas de hausse de tension lors d’un

sinistre.

SmartGuard

Protège contre les baisses de tension et les

conditions de surtension dangereuses. Déconnecte

l’alimentation lorsque la tension d’entrée tombe

en dessous de 95 Volts ou s’élève au-dessus de 140

Volts, puis la reconnecte lorsque la tension retrouve

un niveau stable et sûr.

Cercle de protection

L’indicateur LED surveille l’état du câblage de sortie,

de la tension et de la protection.

Protection Coaxiale et téléphonique

Protège les lignes téléphoniques et les câbles

coaxiaux contre les surtensions tout en maintenant

la totalité de la bande passante de connexions

internet câble/ADSL pour vous assurer une vitesse

exceptionnelle et des vidéos en haute dénition.

Garantie à vie

Garantie limitée à vie du produit en complément

d’une politique de protection d’équipement

connecté de $ 500,000.

Este paquete incluye:

(1) Protector de sobretensión con ocho enchufes

POWER360

(2) Estación de carga por USB modular.

(2) Cable de 1,8 m de micro-USB a USB.

(Para conectar la estación de carga a la unidad

base)

(2) Pies de goma para el módulo de carga

(1) Manual del usuario

Ce pack comprend :

(1) Huit protections de surtension murales

POWER360

(2) Stations modulaires de chargement USB

(2) Câble micro-USB vers USB (6 pouces)

(pour connecter la station de charge à l'unité de

base)

(2) Les pieds en caoutchouc pour le module

(1) Guilde d'utilisateur

English

Properly Connecting Your

PANAMAX POWER360

To completely protect your equipment from surges, every wire leading

into or out of the equipment you want to protect must be connected

to the appropriate Panamax surge protector. Damaging lightning and

power surges can enter your system through any AC power or signal-line

(phone line, grounding wires, coax cables, modem cables, LAN cables,

etc.) connected to your electronic equipment.

The Panamax Connected Equipment Protection Policy is void if any

wire leading into or out of the equipment is not properly connected to

the appropriate Panamax surge protector. The surge protector must also

be plugged into a properly wired and grounded outlet. Please see the

warranty for details or contact the Panamax Tech Support Department

with questions.

Important Safety Points

Panamax POWER360 and the connected equipment must be indoors,

in a dry location and in the same building. Although your Panamax

POWER360 is very durable, its internal components are not isolated from

the environment. Do not install any Panamax product near heat emitting

appliances such as a radiator or heat register. Do not install this product

where excessive moisture is present; for example near a bathtub, sink,

pool, basement oor, sh tank, etc. It is not uncommon for a building to

be improperly grounded. In order to protect your equipment, Panamax

products must be plugged into a properly wired and grounded 3-wire

outlet. Additionally, building wiring and grounding must conform to

applicable NEC (USA) or CEC (Canada) codes for the Panamax protection

policy to be valid.

Circle of Protection

The CIRCLE OF PROTECTION provides peace of mind that your connected

equipment is safe. When all lights are blue, you can rest assured that

your electronics are protected.

1. PROTECTED

BLUE indicates that the POWER360 is functioning properly and that

all connected equipment is protected. OFF indicates that the power

is disconnected from the outlets. If this light is OFF and the VOLTAGE

light is illuminated BLUE, then the PROTECT OR DISCONNECT feature

in your POWER360 has protected your equipment from a catastrophic

surge event and disconnected power. Unplug all electronics from your

POWER360 and contact Panamax Tech Support for assistance.

2. WIRING

BLUE indicates that the wall outlet is properly wired and grounded.

RED indicates an open ground (no ground wire) or reverse wiring

(polarity) condition is detected. Unplug all electronics from your

POWER360 and contact Panamax Tech Support for assistance.

3. VOLTAGE

BLUE indicates that incoming voltage is within a safe range.

RED indicates an over-voltage or brownout condition and that

POWER360 has disconnected power to connected equipment to keep it

safe. POWER360 will automatically reset when voltage is back within a

safe range. If condition persists, it is advisable to contact an electrician

or your power company to determine the cause of the abnormal voltage

issue.

Installation

NOTE to TV ANTENNA, SATELLITE DISH and CATV INSTALLERS:

Articles 810.21 and 820.40 of the NEC provide specic guidelines for

proper grounding, and in particular, specify that the cable ground shall

be connected to the grounding system of the building, as close to the

point of cable entry as practical.

Installing (AC Power):

1. Turn OFF the power to all equipment that will be plugged into the

unit.

2. Make sure that the ON/OFF switch is in the OFF position. Plug the

unit into the wall outlet and then turn it ON.

3. Verify that the “Wiring” LED is BLUE, indicating that the wall outlet

is properly wired.

4. Plug the equipment to be protected into the POWER360 unit and,

one at a time, turn each piece of connected equipment ON and check

for correct operation.

5. Turn OFF the unit and all connected equipment before connecting

any signal lines.

Installing (Telephone Lines):

(Note: Telephone patch cables not included)

IMPORTANT: Note the position of the IN and OUT jacks on the

POWER360 unit. IN is for the line connection that comes from the

wall or oor jack. OUT is for the line connection to your connected

equipment. The protection circuit will only function if connected

properly. Reversed connections will pass the signal to the connected

equipment but will also prevent the protection circuitry from

working and will invalidate the Panamax Connected Equipment

Protection Policy.

1. Make sure the POWER360 and all connected equipment is turned

OFF.

2. Take the incoming telephone line and plug it into the appropriate

IN jack on the protector. The line should now be connected between

the wall and the POWER360 unit.

3. Plug a telephone line (not included) into the OUT jack and then

plug the other end into the equipment to be protected.

4. Turn On the protector and the connected equipment. Verify that

each piece of connected equipment is receiving power and signal.

Installing (Coaxial Lines):

(Coaxial patch cables not included)

Note the position of the IN and OUT jacks on the POWER360 unit. IN

is for the line connection that comes from the wall or oor jack. OUT

is for the line connection to your connected equipment.

The POWER360 coaxial protection circuits achieve optimum signal

quality from Panamax’s coaxial protectors that have the smallest

signal loss on the market – less than 0.5dB of attenuation from 0MHz

to 2.2GHz. Our coaxial protection has been specically designed to

virtually eliminate signal loss to ensure HD video and high speed

internet performance is not compromised. The clamping level of 75

volts will meet the demands of both cable and satellite voltage while

minimizing exposure to spikes and surges.

NOTE: The CATV/Sat/Antenna protection circuit in these models is

bi-directional and has been designed to work with cable TV systems

that send pay-per-view ordering information to the cable company

over the coaxial line.

Make sure that your equipment is connected to the proper jacks.

When used with diplexers, this protection circuit must be placed

between the diplexer and the Satellite receiver; it will not

protect the diplexer.

1. Make sure the Panamax protector and all connected equipment

is turned OFF.

2. Connect the coaxial cable from the CATV system, antenna, or

Satellite dish to the appropriate LINE connector on the POWER360.

3. Connect a coaxial cable from the EQUIP jack on the protector

to appropriate input jack on your TV, cable modem or Satellite

receiver.

USB Charging Station:

Your POWER360 includes two modular dual-port charging stations.

The unique, patent-pending design of these charging stations allows

them to be removed from the base unit and placed on a nearby desk

or table top for easy access.

The charging station must be tethered to, or plugged directly

into, your base unit to charge. A 6’ tether cable is included for each

charging station. If you require a longer cable, various lengths of

standard USB-to-Micro USB cables are commonly available. Rubber

feet are included for your charging stations. Applied on the bottom

and towards the front of your charging station, they will help keep

your charging stations in place. Each charging station can handle up

to 2.1A capacity, typically enough for 2 mobile devices or 1 tablet. The

USB charging ports are surge-protected.

Wall Mounting:

Your POWER360 may be axed to a wall or other at surface.

1. Determine the mounting location. Hold the POWER360 unit

up against the location and mark drilling positions using the

mounting guides on the sides of the unit. Note: You are marking

the center point where you would like the unit to be mounted.

2. Drive a #6 screw into each drilling position. Leave approximately

1/8” of space between the back of the screw head and the wall.

3. Position the POWER360 over the two screws and slide down to

lock into place.

4. Using the above procedure allows easy removal of the unit

by sliding up to disengage the unit from the screws.

Troubleshooting

The CIRCLE OF PROTECTION is not lit, there is no AC power

to my equipment, or my equipment doesn’t turn on.

- Make sure POWER360 is plugged into a working AC outlet.

- Verify the “VOLTAGE” indicator on the CIRCLE OF PROTECTION

is Blue. If Red, the incoming line voltage is either too high

or too low and has been disconnected from your connected

equipment.

- Make sure the switch/circuit breaker is in the ON position.

- If you still have no power, POWER360 may be damaged.

Contact Panamax Tech Support.

My mobile device is not charging.

- Some devices may be incompatible with this USB charging

port. Although the device may report that it is not charging,

it is most likely to be charging at a lower (0.5 Amp) current.

- When charging two devices it is possible that that USB

charging circuitry may be overloaded. Disconnect one of the

devices.

- Make sure the tether cable is connected between the

charging station and base unit, or the charging station is

completely plugged into the base unit.

There is no audio or video from my cable box and/or my

cable modem is not connecting.

- Check the coaxial connections, making sure they are correctly

and securely installed.

- Try a dierent coaxial cable.

- Bypass the coaxial connectors. If your picture returns, the

protector is damaged. Contact Panamax (website or Tech

Support Department) for replacement.

- If you still have no picture, a problem with your cable

provider’s signal may exist.

(Note: Coaxial patch cables not included)

My telephone, DSL modem or fax machine has AC power

but still does not work.

- Check to see if your connected equipment is receiving a dial

tone.

- Try a dierent telephone cable, or try the equipment with a

dierent telephone jack.

- Bypass the telephone connectors. If your dial tone returns,

the protector is damaged. Contact Panamax (website or Tech

Support Department) for replacement.

- If you still have no dial tone, a problem with the phone

company’s lines may exist.

The Panamax circuit breaker disconnects AC power from

the connected equipment.

- You have exceeded the ampere rating for your surge

protector. As a temporary x, disconnect one or more pieces

of equipment. Ask your Panamax dealer about additional

Panamax protectors that may be required.

PANAMAX TECH SUPPORT: 1-800-472-5555

www.panamax.com/POWER360

English

Warranty and Connected Equipment Policy Information

CAUTION!

All Panamax Warranties and Connected Equipment Policies are valid only in the United States and Canada.

CAUTION!

Audio/Video, computer and/or telephone system installations can be very complex systems, consisting of many interconnected components.

Due to the nature of electricity and surges, a single protector may not be able to completely protect complex installations. In those cases, a systematic approach using multiple protectors must be employed. Systematic protection

requires professional design. AC power, satellite cables, CATV cables, telephone/network lines, signal lines or any other electrical conductors, entering the system that do not pass through this surge protector may invalidate the

Panamax Connected Equipment Protection Policy. For additional information on how to protect your system, please contact Panamax before connecting your equipment to the surge protector.

CAUTION! WARRANTY LIMITATION FOR INTERNET PURCHASERS

Panamax products purchased through the Internet do not carry a valid Product Warranty or Connected Equipment Protection Policy unless purchased from an Authorized Panamax Internet Dealer and the original factory serial

numbers are intact (they must not have been removed, defaced or replaced in any way). Purchasing from an Authorized Panamax Internet Dealer insures that the product was intended for consumer use, has passed all quality

inspections and is safe. Buying through auction sites or unauthorized dealers may result in the purchase of salvaged, failed and/or products not intended for use in the US. In addition, Authorized Panamax Internet dealers have

demonstrated sucient expertise to insure warranty compliant installations. For a list of Authorized Panamax Internet Dealers go to www.panamax.com. If you have any questions regarding these requirements, please contact

Panamax Tech Support.

Product Upgrade Program

If your Panamax power conditioner sacrices itself

while protecting your connected equipment, you

have an option to upgrade to the latest technology.

Please go to our web site www.panamax.com or

contact Panamax Tech Support at 800-472-5555 for

details.

Panamax Surge Protector Lifetime Limited

Product Warranty

Panamax warrants to the purchaser of any standard

Panamax surge protector that the surge protector

shall be free of defects in design, material, or

workmanship, and Panamax will repair or replace

any defective unit. For product replacement see

“NOTIFICATION” (3).

Panamax Surge Protector Limited

Connected Equipment Protection Policy

It is the policy of Panamax that it will, at its election,

either replace, pay to replace at fair market value, or

pay to repair, up to the dollar amount specied below,

equipment that is damaged by an AC power, cable,

telephone, or lightning surge while connected to a

properly installed Panamax power conditioner. To be

eligible for compensation, repair and or replacement,

the power conditioner must shows signs of surge

damage or that it is operating outside of design

specications, relative to its surge protection

capability, and under all of the circumstances failed

to protect your connected equipment.

$500,000 CONNECTED EQUIPMENT POLICY

THE CONNECTED EQUIPMENT POLICY IS

SUBJECT TO THE FOLLOWING CONDITIONS

AND LIMITATIONS

1. ORIGINAL OWNERSHIP REQUIREMENT:

Panamax’s connected equipment policy extends to

the original purchaser of the Panamax product only

and is non-transferable. Original purchase receipts

must accompany any product return or claim for

connected equipment damage.

2. PROPER INSTALLATION:

Panamax AC protectors must be directly plugged

into a properly grounded 3-wire AC outlet. Extension

cords*, non-grounded two prong adapters, or other

non-Panamax surge products must not be used.

Building wiring and other connections to protected

equipment must conform to applicable codes (NEC

or CEC). No other ground wires or ground connections

may be used. All wires (including, e.g., AC power

lines, telephone lines, signal/data lines, coaxial

cable, antenna lead-ins) leading into the protected

equipment must rst pass through a single Panamax

protector designed for the particular application. The

protector and the equipment to be protected must be

indoors in a dry location, and in the same building.

Panamax installation instructions and diagrams must

be followed

3. NOTIFICATION:

You must notify Panamax within ten days of any

event precipitating request for product replacement

or payment for connected equipment damage.

A return authorization (RA) number must rst

be obtained from the Panamax Tech Support

Department at www.panamax.com** before

returning the protector Panamax. At this time,

you must notify Panamax if you believe you have a

claim for damaged connected equipment. Once you

obtain an RA number, please mark the number on the

bottom of the unit and pack it in a shipping carton/

box with enough packing material to protect it during

transit. The RA number must also be clearly marked

on the outside of the carton. Ship the unit Panamax.

Please note that you are responsible for any and all

charges related to shipping the unit to Panamax. If

connected equipment damage was indicated on your

RA request, Panamax will mail you claim kit to be

completed and returned within 30 days. A connection

diagram of your system will be required as part of

the claim kit. Be sure to note its conguration before

disconnecting your equipment.

4. DETERMINATION OF FAILURE:

Panamax will evaluate the protector for surge

damage. The Panamax protector must show signs of

surge damage or must be performing outside (>10%)

of design specications relative to its surge protection

capability. Opening the enclosure, tampering with,

or modifying the unit in any way shall be grounds

for an automatic denial your request for payment.

Panamax, after evaluating all information provided,

will determine whether or not your request is eligible

for payment. If the surge protector shows no signs

of AC power or signal line surge damage and is

working within design specications, Panamax will

return the unit to you with a letter explaining the

test results and notifying you of the rejection your

claim. Exceptions: If a dealer or installer replaces

the protector for the customer, replacement will be

returned to the dealer installer; or if the protector

is a pre-1996 model, it will be replaced; or, for a

Canadian customer, the protector will be replaced.

Panamax reserves the right to inspect the damaged

connected equipment, parts, or circuit boards. Please

note that you are responsible for any and all charges

related to shipping the damaged equipment to

Panamax. Panamax also reserves the right to inspect

the customer’s facility. Damaged equipment deemed

uneconomical to repair must remain available for

inspection by Panamax until the claim is nalized.

5. REQUEST PAYMENTS:

Once Panamax has determined that you are entitled

to compensation, Panamax will, at its election, either

pay you the present fair market value of the damaged

equipment, or pay for the cost of the repair, or send

you replacement equipment, or pay the equivalence

of replacement equipment.

6. OTHER INSURANCE/WARRANTIES:

This coverage is secondary to any existing

manufacturer’s warranty, implied or expressed, or

any insurance and/or service contract that may cover

the loss.

7. EXCLUSIONS:

THE PANAMAX CONNECTED EQUIPMENT

PROTECTION POLICY DOES NOT APPLY TO:

Service charges, installation costs, reinstallation

costs; setup cost; diagnostic charges; periodic

checkups; routine maintenance; loss of use of

the product; costs or expenses arising out of

reprogramming or loss of programming and/or data;

shipping charges or fees; service calls; loss or damage

occasioned by re, theft, ood, wind, accident, abuse

or misuse, and products subject to manufacturer’s

recall or similar event.

8. DISPUTE RESOLUTION:

Any controversy or claim arising out of or relating to

Panamax’s Connected Equipment Protection Policy,

or the alleged breach thereof, shall be settled by

arbitration administered by the American Arbitration

Association under its Commercial Arbitration Rules.

You may le for arbitration at any AAA location in

the United States upon the payment of the applicable

ling fee. The arbitration will be conducted before

a single arbitrator, and will be limited solely to the

dispute or controversy between you and Panamax.

The arbitration shall be held in any mutually

agreed upon location in person, by telephone, or

online. Any decision rendered in such arbitration

proceedings will be nal and binding on each of

the parties, and judgment may be entered thereon

in a court of competent jurisdiction. The arbitrator

shall not award either party special, exemplary,

consequential, punitive, incidental or indirect

damages, or attorney’s fees. The parties will share

the costs of arbitration (including the arbitrator’s

fees, if any) in the proportion that the nal award

bears to the amount of the initial claim.

9. GENERAL:

If you have any questions regarding the product

warranty or the connected equipment protection

policy, please contact the Panamax Tech Support

Department at www.panamax.com. The Limited

Product Warranty and Connected Equipment Policy

herein supersede all previous warranties and/or

Connected Equipment repair/replacement policies.

THE LIMITED PRODUCT WARRANTY IS THE ONLY

WARRANTY PROVIDED WITH THIS PANAMAX

PRODUCT AND ANY OTHER IMPLIED OR

EXPRESSED WARRANTIES ARE NON-EXISTENT.

This warranty may not be modied except in writing,

signed by an ocer of the Panamax Corporation.

* The use of a Panamax extension cord or equivalent

(UL or CSA listed, minimum 14AWG, 3-wire grounded)

will not invalidate the warranty.

** Forms are available on the Panamax web site for

requesting RAs and opening a claim for connected

equipment damage.

Page is loading ...

PROTECTED

PROTEGIDA

PROTÉGÉ

VOLTAGE

TENSIÓN

TENSION

WIRING

CABLEADO

CÂBLAGE

Circle of Protection

PANAMAX TECH SUPPORT: 1-800-472-5555

www.panamax.com/POWER360

2. 3.

are

registered trademarks of Core Brands, LLC. Designed and Engineered in the USA.

Manufactured to Panamax quality specications in China.

P/N: 10002440 Rev-A

Panamax P360-8 User manual

Brand: Panamax

Model: P360-8

Type: User manual

Download PDF

report

in other languages

français: Panamax P360-8 Manuel utilisateur
español: Panamax P360-8 Manual de usuario

Panamax P360-8 User manual

Panamax P360-8 User manual

in other languages

Related papers

Other documents