Copystar ECOSYS FS-C5400DN Operating instructions

OPERATION GUIDE

Please read this Operation Guide before using this machine. Keep it close to the machine for easy reference.

FS-C5400DN

iii

Contents

Legal and Safety Information

1 Machine Parts

Components at the Front of the Printer ................................... 1-2

Components at the Left of the Printer ...................................... 1-2

Internal Components .................................................................. 1-3

Components at the Rear of the Printer ..................................... 1-3

Operation Panel .......................................................................... 1-4

2 Printing Operation

Changing Network Interface Parameters ................................. 2-2

Printing a Status Page ............................................................... 2-3

Installing the Printer Driver ....................................................... 2-4

Printing from Application Software .......................................... 2-9

Status Monitor .......................................................................... 2-10

Uninstalling Software (Windows PC) ...................................... 2-13

3 Handling Paper

General Guidelines ..................................................................... 3-2

Selecting the Right Paper .......................................................... 3-4

Special Paper .............................................................................. 3-7

Paper Type ................................................................................ 3-13

Loading Paper ........................................................................... 3-14

4 Using the Operation Panel

General Information ................................................................... 4-2

Understanding the Operation Panel ......................................... 4-3

Keys ............................................................................................. 4-6

Using the Menu Selection System ............................................ 4-8

Setting a Mode Selection Menu ............................................... 4-10

Report Print ............................................................................... 4-11

USB Memory (USB memory selection) ................................... 4-17

Custom Box .............................................................................. 4-21

Job Box ..................................................................................... 4-26

Job Log ...................................................................................... 4-38

Counter (Viewing the counter value) ...................................... 4-40

Paper Settings .......................................................................... 4-42

Print Settings ............................................................................ 4-54

Network (Network settings) ..................................................... 4-64

Device Common (Selecting/Setting the common device) .... 4-71

Security (Security function setting) ........................................ 4-85

Job Account.Set. (Job Account setting) ................................ 4-94

Administrator (Administrator settings) ................................ 4-103

Adjust/Maint. (Adjust/Maintenance selection/setting) ........ 4-106

5 Maintenance

General Information ................................................................... 5-2

Toner Container Replacement .................................................. 5-2

Replacing the Waste Toner Box ................................................ 5-6

Cleaning the Printer ................................................................... 5-8

6 Troubleshooting

General Guidelines ..................................................................... 6-2

Print Quality Problems ............................................................... 6-3

Error Messages ........................................................................... 6-5

Clearing Paper Jams ................................................................ 6-15

iv

Appendix

Interface .......................................................................................A-2

USB Interface ..............................................................................A-2

Network Interface ........................................................................A-3

About the Options ......................................................................A-5

Expansion Memory Modules .....................................................A-6

General Description of Options .................................................A-9

Specifications ...........................................................................A-12

Glossary

Index

v

Legal and Safety Information

Notice on Software

SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE

PRINTER'S EMULATION MODE. The printer is factory-set to emulate the

PCL.

Notice

The information in this guide is subject to change without notification.

Additional pages may be inserted in future editions. The user is asked to

excuse any technical inaccuracies or typographical errors in the present

edition.

No responsibility is assumed if accidents occur while the user is following

the instructions in this guide. No responsibility is assumed for defects in

the printer's firmware (contents of its read-only memory).

This guide, any copyrightable subject matter sold or provided with or in

connection with the sale of the page printer, are protected by copyright.

All rights are reserved. Copying or other reproduction of all or part of this

guide, any copyrightable subject matter without the prior written consent

of Kyocera Mita Corporation is prohibited. Any copies made of all or part

of this guide, any copyrightable subject must contain the same copyright

notice as the material from which the copying is done.

Regarding Tradenames

PRESCRIBE is a registered trademark of Kyocera Corporation. KPDL is

trademark of Kyocera Corporation.

Hewlett-Packard, PCL, and PJL are registered trademarks of Hewlett-

Packard Company. Centronics is a trade name of Centronics Data

Computer Inc. PostScript is a registered trademark of Adobe Systems

Incorporated. Macintosh, Bonjour are registered trademarks of Apple

Computer, Inc. Microsoft, Windows, and Windows NT are registered

trademarks of Microsoft Corporation. PowerPC and Microdrive are

trademarks of International Business Machines Corporation.

CompactFlash is a trademark of SanDisk Corporation. ENERGY STAR is

a U.S. registered mark. All other brand and product names are registered

trademarks or trademarks of their respective companies.

This product was developed using the Tornado™ Real Time Operating

System and Tools from Wind River Systems.

This product contains UFST™ and MicroType

®

from Monotype Imaging

Inc.

CAUTION NO LIABILITY IS ASSUMED FOR ANY

DAMAGE CAUSED BY IMPROPER INSTALLATION.

vi

License Agreements

Typeface Trademark Acknowledgement

All resident fonts in this printer are licensed from Monotype Imaging Inc.

Helvetica, Palatino and Times are registered trademarks of Linotype-Hell

AG. ITC Avant Garde Gothic, ITC Bookman, ITC ZapfChancery and ITC

Zapf Dingbats are registered trademarks of International Typeface

Corporation.

Monotype Imaging License Agreement

1 “Software” shall mean the digitally encoded, machine readable,

scalable outline data as encoded in a special format as well as the

UFST Software.

2 You agree to accept a non-exclusive license to use the Software to

reproduce and display weights, styles and versions of letters,

numerals, characters and symbols (“Typefaces”) solely for your own

customary business or personal purposes at the address stated on

the registration card you return to Monotype Imaging. Under the

terms of this License Agreement, you have the right to use the Fonts

on up to three printers. If you need to have access to the fonts on

more than three printers, you need to acquire a multi-user license

agreement which can be obtained from Monotype Imaging.

Monotype Imaging retains all rights, title and interest to the Software

and Typefaces and no rights are granted to you other than a License

to use the Software on the terms expressly set forth in this

Agreement.

3 To protect proprietary rights of Monotype Imaging, you agree to

maintain the Software and other proprietary information concerning

the Typefaces in strict confidence and to establish reasonable

procedures regulating access to and use of the Software and

Typefaces.

4 You agree not to duplicate or copy the Software or Typefaces,

except that you may make one backup copy. You agree that any

such copy shall contain the same proprietary notices as those

appearing on the original.

5 This License shall continue until the last use of the Software and

Typefaces, unless sooner terminated. This License may be

terminated by Monotype Imaging if you fail to comply with the terms

of this License and such failure is not remedied within thirty (30)

days after notice from Monotype Imaging. When this License expires

or is terminated, you shall either return to Monotype Imaging or

destroy all copies of the Software and Typefaces and documentation

as requested.

6 You agree that you will not modify, alter, disassemble, decrypt,

reverse engineer or decompile the Software.

7 Monotype Imaging warrants that for ninety (90) days after delivery,

the Software will perform in accordance with Monotype Imaging-

published specifications, and the diskette will be free from defects in

material and workmanship. Monotype Imaging does not warrant that

the Software is free from all bugs, errors and omissions.

8 THE PARTIES AGREE THAT ALL OTHER WARRANTIES,

EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF

FITNESS FOR A PARTICULAR PURPOSE AND

MERCHANTABILITY, ARE EXCLUDED.

vii

9 Your exclusive remedy and the sole liability of Monotype Imaging in

connection with the Software and Typefaces is repair or replacement

of defective parts, upon their return to Monotype Imaging.

10 IN NO EVENT WILL MONOTYPE IMAGING BE LIABLE FOR LOST

PROFITS, LOST DATA, OR ANY OTHER INCIDENTAL OR

CONSEQUENTIAL DAMAGES, OR ANY DAMAGES CAUSED BY

ABUSE OR MISAPPLICATION OF THE SOFTWARE AND

TYPEFACES.

11 Massachusetts U.S.A. law governs this Agreement.

12 You shall not sublicense, sell, lease, or otherwise transfer the

Software and/or Typefaces without the prior written consent of

Monotype Imaging.

13 Use, duplication or disclosure by the Government is subject to

restrictions as set forth in the Rights in Technical Data and Computer

Software clause at FAR 252-227-7013, subdivision (b)(3)(ii) or

subparagraph (c)(1)(ii), as appropriate. Further use, duplication or

disclosure is subject to restrictions applicable to restricted rights

software as set forth in FAR 52.227-19 (c)(2).

14 YOU ACKNOWLEDGE THAT YOU HAVE READ THIS

AGREEMENT, UNDERSTAND IT, AND AGREE TO BE BOUND BY

ITS TERMS AND CONDITIONS. NEITHER PARTY SHALL BE

BOUND BY ANY STATEMENT OR REPRESENTATION NOT

CONTAINED IN THIS AGREEMENT. NO CHANGE IN THIS

AGREEMENT IS EFFECTIVE UNLESS WRITTEN AND SIGNED

BY PROPERLY AUTHORIZED REPRESENTATIVES OF EACH

PARTY. BY OPENING THIS DISKETTE PACKAGE, YOU AGREE

TO ACCEPT THE TERMS AND CONDITIONS OF THIS

AGREEMENT.

GPL

Firmware of this machine is using in part the GPL applied codes

(www.fsf.org/copyleft/gpl.html). Please access "http://

www.kyoceramita.com/gpl" for more information on how to make GPL

applied codes available.

Open SSLeay License

Redistribution and use in source and binary forms, with or without

modification, are permitted provided that the following conditions are met:

1 Redistributions of source code must retain the above copyright

notice, this list of conditions and the following disclaimer.

2 Redistributions in binary form must reproduce the above copyright

notice, this list of conditions and the following disclaimer in the

documentation and/or other materials provided with the distribution.

3 All advertising materials mentioning features or use of this software

must display the following acknowledgment:

"This product includes software developed by the OpenSSL Project

for use in the OpenSSL Toolkit. (http://www.openssl.org/)"

4 The names "OpenSSL Toolkit" and "OpenSSL Project" must not be

used to endorse or promote products derived from this software

without prior written permission.

For written permission, please contact [email protected].

5 Products derived from this software may not be called "OpenSSL"

nor may "OpenSSL" appear in their names without prior written

permission of the OpenSSL Project.

viii

6 Redistributions of any form whatsoever must retain the following

acknowledgment: "This product includes software developed by the

OpenSSL Project for use in the OpenSSL Toolkit (http://

www.openssl.org/)"

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT "AS IS"

AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT

NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE

ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR

ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,

INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF

SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR

PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND

ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT

LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)

ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN

IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Original SSLeay License

reserved.

This package is an SSL implementation written by Eric Young

([email protected]). The implementation was written so as to conform

with Netscapes SSL.

This library is free for commercial and non-commercial use as long as the

following conditions are aheared to. The following conditions apply to all

code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code;

not just the SSL code. The SSL documentation included with this

distribution is covered by the same copyright terms except that the holder

is Tim Hudson ([email protected]).

Copyright remains Eric Young's, and as such any Copyright notices in the

code are not to be removed.

If this package is used in a product, Eric Young should be given attribution

as the author of the parts of the library used.

This can be in the form of a textual message at program startup or in

documentation (online or textual) provided with the package.

Redistribution and use in source and binary forms, with or without

modification, are permitted provided that the following conditions are met:

1 Redistributions of source code must retain the copyright notice, this

list of conditions and the following disclaimer.

2 Redistributions in binary form must reproduce the above copyright

notice, this list of conditions and the following disclaimer in the

documentation and/or other materials provided with the distribution.

3 All advertising materials mentioning features or use of this software

must display the following acknowledgement:

"This product includes cryptographic software written by Eric Young

(eay@cryptsoft.com)"

The word 'cryptographic' can be left out if the rouines from the library

being used are not cryptographic related :-).

ix

4 If you include any Windows specific code (or a derivative thereof)

from the apps directory (application code) you must include an

acknowledgement:

"This product includes software written by Tim Hudson

([email protected])"

THIS SOFTWARE IS PROVIDED BY ERIC YOUNG "AS IS" AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT

LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN

NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE

FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,

OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED

TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS

OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)

HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,

WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE

USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY

OF SUCH DAMAGE.

The licence and distribution terms for any publically available version or

derivative of this code cannot be changed. i.e. this code cannot simply be

copied and put under another distribution licence [including the GNU

Public Licence.]

x

Compliance and Conformity

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

• The use of a non-shielded interface cable with the referenced device

is prohibited.

CAUTION

— The changes or modifications not expressly approved by

the party responsible for compliance could void the user’s authority to

operate the equipment.

This device complies with Part 15 of FCC Rules and RSS-Gen of IC

Rules.

Operation is subject to the following two conditions; (1) this device may

not cause interference, and (2) this device must accept any interference,

including interference that may cause undesired operation of the device.

* The above warning is valid only in the United States of America.

Interface connectors

IMPORTANT Be sure to power off the printer before connecting or

disconnecting an interface cable. For protection against static

electricity discharge to the printer's internal electronics through the

interface connector(s), cover any interface connector that is not in use

with the protective cap supplied.

Note Use shielded interface cables.

xi

Safety Information

Laser Safety

This printer is certified as a Class 1 laser product under the U.S.

Department of Health and Human Services (DHHS) Radiation

Performance Standard according to Radiation Control for Health and

Safety Act of 1968. This means that the printer does not produce

hazardous laser radiation. Since radiation emitted inside the printer is

completely confined within protective housings and external covers, the

laser beam cannot escape from the printer during any phase of user

operation.

Laser Notice

This printer is certified in the U.S. to conform to the requirements of DHHS

21 CFR Subchapter for Class I (1) laser products, and elsewhere is

certified as a Class I laser product conforming to the requirements of IEC

825.

Radio Frequency Transmitter

This machine contains a transmitter module. We, the manufacturer

(Kyocera Mita Corporation) hereby declare that this equipment (page

printer), model FS-C5400DN is in compliance with the essential

requirements and other relevant provisions of Directive 1999/5/EC.

Radio Tag Technology

In some countries, the radio tag technology used in this equipment to

identify the toner container may be subject to authorization, and the use

of this equipment may consequently be restricted.

DANGER CLASS 3B LASER RADIATION WHEN OPEN.

AVOID DIRECT EXPOSURE TO BEAM.

CAUTION Use of controls or adjustments or performance

of procedures other than those specified herein may result

in hazardous radiation exposure.

xii

Cautionary Labels

The printer bears any of the following labels.

For Europe, Asia, and other countries

For U.S.A. and Canada

High temperature inside. Do

not touch parts in this area,

because there is a danger of

getting burned.

Label inside the printer (Laser radiation warning)

xiii

CDRH Regulations

The Center for Devices and Radiological Health (CDRH) of the U.S. Food

and Drug Administration implemented regulations for laser products on

August 2, 1976. These regulations apply to laser products manufactured

after August 1, 1976. Compliance is mandatory for products marketed in

the United States. A label indicating compliance with the CDRH

regulations must be attached to laser products marketed in the United

States.

Ozone concentration

The printers generate ozone gas (O

3

) which may concentrate in the place

of installation and cause an unpleasant smell. To minimize the

concentration of ozone gas to less than 0.1 ppm, we recommend you not

to install the printer in a confined area where ventilation is blocked.

Safety Instructions Regarding the Disconnection of Power

Caution: The power plug is the main isolation device! Other switches on

the equipment are only functional switches and are not suitable for

isolating the equipment from the power source.

VORSICHT: Der Netzstecker ist die Hauptisoliervorrichtung! Die anderen

Schalter auf dem Gerät sind nur Funktionsschalter und können nicht

verwendet werden, um den Stromfluß im Gerät zu unterbrechen.

DECLARATION OF CONFORMITY

TO

2004/108/EC, 2006/95/EEC, 93/68/EEC, 1999/5/EC and 2005/32/EC

We declare under our sole responsibility that the product to which this

declaration relates is in conformity with the following specifications.

EN55024

EN55022 Class B

EN61000-3-2

EN61000-3-3

EN60950-1

EN60825-1

EN300 330-1

EN300 330-2

EN62301

xiv

Canadian Department of Communications Compliance

Statement

This Class B digital apparatus complies with Canadian ICES-003.

Avis de conformité aux normes du ministère des

Communications du Canada

Cet appareil numérique de la classe B est conforme à la norme NMB-003

du Canada.

EN ISO 7779

Maschinenlärminformations-Verordnung 3. GPSGV, 06.01.2004: Der

höchste Schalldruckpegel beträgt 70 dB (A) oder weniger gemäß EN ISO

7779.

Disclaimer

Kyocera Mita will not be liable to customers or any other person or entity

for any loss or damage caused or alleged to be caused directly or

indirectly by equipment sold or furnished by us, including but not limited

to, any interruption of service, loss of business or anticipatory profits, or

consequential damages resulting from the use or operation of the

equipment or software.

xv

Energy Saving Control Function

To reduce energy consumption while in a waiting state, the device comes

equipped with an energy saving control function for switching to a Sleep

Mode where power consumption is automatically reduced to a minimum

after a certain amount of time elapses since the device was last used.

Sleep

The device automatically enters Sleep when 45 minutes have passed

since the device was last used. The amount of time of no activity that must

pass before Sleep is activated may be lengthened. For more information,

refer to Sleep Timer (Sleep timer timeout setting) section.

Automatic 2-Sided Print Function

This device includes 2-sided printing as a standard function. For example,

by printing two 1-sided originals onto a single sheet of paper as a 2-sided

print, it is possible to lower the amount of paper used. For more

information, refer to Duplex (Duplex Printing) section.

Paper Recycling

This device supports the recycled paper which reduces the load on the

environment. Your sales or service representative can provide

information about recommended paper types.

Energy Star (ENERGY STAR

®

) Program

We have determined as a participating company in the International

Energy Star Program that this product is compliant with the standards laid

out in the International Energy Star Program.

xvi

Installation Precautions

Environment

Other Precautions

Adverse environmental conditions may affect the safe operation and

performance of the printer. Install in an air-conditioned room

(recommended room temperature: around 23 °C, humidity: around 60 %

RH) and avoid the following locations when selecting a site for the printer.

- Avoid locations near a window or with exposure to direct sunlight.

- Avoid locations with vibrations.

- Avoid locations with drastic temperature fluctuations.

- Avoid locations with direct exposure to hot or cold air.

- Avoid poorly ventilated locations.

If the flooring is of a soft material, it may be damaged by the casters when

this product is moved after installation.

CAUTION Avoid placing the printer on or in locations which

are unstable or not level. Such locations may cause the

printer to fall. This type of situation presents a danger of

personal injury or damage to the printer.

Avoid locations with humidity or dust and dirt. If dust or dirt

becomes attached to the power plug, clean the plug to avoid

the danger of fire or electrical shock.

Avoid locations near radiators, heaters, or other heat

sources, or locations near flammable items, to avoid the

danger of fire.

To keep the printer cool and facilitate changing of parts and

maintenance, allow access space as shown below. Leave

adequate space, especially around the side cover, to allow

air to be properly ventilated from the printer.

Left: 400 mm

(16 inches)

Right: 250 mm

(10 inches)

Rear: 200 mm

(7-7/8 inches)

Front: 600 mm

(23-5/8 inches)

Top: 400 mm

(16 inches)

xvii

Power Supply/Grounding the Printer

Other Precautions

Connect the power plug to the closest outlet possible to the printer.

Handling of Plastic Bags

WARNING Do not use a power supply with a voltage other

than that specified. Avoid multiple connections in the same

outlet. These types of situations present a danger of fire or

electrical shock.

Plug the power cord securely into the outlet. If metallic objects

come in contact with the prongs on the plug, it may cause a fire

or electric shock.

Always connect the printer to an outlet with a ground

connection to avoid the danger of fire or electrical shock in

case of an electric short. If an earth connection is not possible,

contact your service representative.

WARNING Keep the plastic bags that are used with the

printer away from children. The plastic may cling to their

nose and mouth causing suffocation.

xviii

Precautions for Use

Cautions when Using the Printer

• Do not place metallic objects or containers with water (flower vases,

flower pots, cups, etc.) on or near the printer. This type of situation

presents a danger of fire or electrical shock should they fall inside.

• Do not remove any of the covers from the printer as there is a danger

of electrical shock from high voltage parts inside the printer.

• Do not damage, break or attempt to repair the power cord. Do not

place heavy objects on the cord, pull it, bend it unnecessarily or cause

any other type of damage.These types of situations present a danger

of fire or electrical shock.

• Never attempt to repair or disassemble the printer or its parts as there

is a danger of fire, electrical shock or damage to the laser. If the laser

beam escapes, there is a danger of it causing blindness.

• If the printer becomes excessively hot, smoke appears from the

printer, there is an odd smell, or any other abnormal situation occurs,

there is a danger of fire or electrical shock. Turn the power switch

OFF ({) immediately, remove the power plug from the outlet and

contact your service representative.

• If anything harmful (paper clips, water, other fluids, etc.) falls into the

printer, turn the power switch OFF ({) immediately. Next, remove the

power plug from the outlet to avoid the danger of fire or electrical

shock. Then contact your service representative.

• Do not remove or connect the power plug with wet hands, as there is

a danger of electrical shock.

• Always contact your service representative for maintenance or repair

of internal parts.

• Do not pull the power cord when removing it from the outlet. If the

power cord is pulled, the wires may become broken and there is a

danger of fire or electrical shock. (Always grasp the power plug when

removing the power cord from the outlet.)

• Always remove the power plug from the outlet when moving the

printer. If the power cord is damaged, there is a danger of fire or

electrical shock.

• If the printer will not be used for a short period of time (overnight, etc.),

turn the power switch OFF ({). If it will not be used for an extended

period of time (vacations, etc.), remove the power plug from the outlet

for safety purposes during the time the printer is not in use.

• For safety purposes, always remove the power plug from the outlet

when performing cleaning operations.

• If dust accumulates within the printer, there is a danger of fire or other

trouble. It is therefore recommended that you consult with your

service representative in regard to cleaning of internal parts. This is

particularly effective if accomplished prior to seasons of high humidity.

Consult with your service representative in regard to the cost of

cleaning the internal parts of the printer.

xix

Other Precautions

• Do not place heavy objects on the printer or cause other damage to

the printer.

• Do not open the top/left/rear cover, turn off the main switch, or pull out

the power plug during printing.

• During printing, some ozone is released, but the amount does not

cause any ill effect to one's health. If, however, the printer is used over

a long period of time in a poorly ventilated room or when printing an

extremely large number of copies, the smell may become unpleasant.

To maintain the appropriate environment for print work, it is suggested

that the room be properly ventilated.

• Do not touch electrical parts, such as connectors or printed circuit

boards. They could be damaged by static electricity.

• Do not attempt to perform any operations not explained in this

handbook.

• If the printer will not be used for an extended period of time, remove

the paper from the cassette, return it to its original package and reseal

it.

Cautions for Toner Handling

• Do not incinerate toner and toner containers. Dangerous sparks may

cause burn.

• Never open the toner container.

• Do not inhale the toner.

• If you get toner on your hands, do not rub your eyes or touch your

mouth. Wash the toner from your hands.

• For the disposal of the old toner container, consult your service

technician or dispose of the toner or toner containers in accordance

with Federal, State and Local rules and regulations.

CAUTION Use of controls or adjustments or performance

of procedures other than those specified herein may result

in hazardous radiation exposure.

xx

About the Operation Guide

This Operation Guide has the following chapters:

Chapter 1 - Machine Parts

This chapter explains the names of parts.

Chapter 2 - Printing Operation

This chapter explains how to print from your workstation.

Chapter 3 - Handling Paper

This chapter explains how to replace the toner container and how to care

for your printer.

Chapter 4 - Using the Operation Panel

This chapter explains how to handle printer problems that may occur,

such as paper jams.

Chapter 5 - Maintenance

This chapter lists the printer’s specifications.

Chapter 6 - Troubleshooting

This chapter explains how to handle error messages, paper jams and

Copystar ECOSYS FS-C5400DN Operating instructions

This manual is also suitable for

Copystar ECOSYS FS-C5400DN Operating instructions

Related papers

Other documents