Riva RTC series Installation guide

www.rivatech.de

RTC series

Installation Guide

RTC Series RTC Installation Guide

01A.04 2

INFORMATION TO USER

CAUTION

RISK OF ELECTRIC SHOCK,

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE THE DEVICE COVER (OR BACK).

CONTACT QUALIFIED SERVICE PERSONNEL FOR INTERNAL

PART SERVICES.

This symbol is intended to alert the user the presence of un-

insulated “dangerous voltage” within the product’s enclosure,

which may be sufficient magnitude to constitute an electric shock

risk to persons.

This symbol is intended to alert the user the presence of

important operating and maintenance (servicing) instructions

within the guide manual

!

RTC Series RTC Installation Guide

01A.04 3

Table of Contents

1. FEATURES .............................................................................. 4

2. PACKAGE CONTENTS ................................................................ 5

3. PART NAMES .......................................................................... 6

3.1. Rear View .................................................................................... 6

3.2. Bottom View ................................................................................ 6

4. CONNECTIONS ........................................................................ 8

4.1.Connectors ................................................................................... 9

5. CONFIGURATION .................................................................... 12

5.1.Set up network environment .......................................................... 12

5.1.1. Generic IP Environment .......................................................... 12

5.1.2. Custom IP Environment .......................................................... 13

5.2. View video on web page ............................................................... 14

5.2.1. View video using IPAdmin Tool ................................................. 15

5.3. Reset ........................................................................................ 16

5.4. Factory Default ........................................................................... 16

APPENDIX (A): SPECIFICATIONS .................................................... 17

Summary .......................................................................................... 17

Environment Condition ........................................................................ 18

Mechanical Condition .......................................................................... 18

APPENDIX (B): THEORATICAL DISTANCE ........................................ 19

APPENDIX (C): POWER OVER ETHERNET ........................................ 20

PoE compatibility ................................................................................ 20

Power classification ............................................................................ 20

APPENDIX (D): DIMENSIONS ........................................................ 21

APPENDIX [E]: CAMERA HOUSING ................................................. 23

Housing Overview ............................................................................... 23

Positioning of Camera Mount by Lens .................................................... 23

Camera Installation ............................................................................ 24

To connect cables .............................................................................. 27

APPENDIX (F): HEXADECIMAL-DECIMAL CONVERSION TABLE ............. 28

REVISION HISTORY ..................................................................... 30

RTC Series RTC Installation Guide

01A.04 4

1. FEATURES

Camera

 17 ㎛ Next Generation Mirobolometer Technology

 320x240 pixels

 42, 19,12, 9 or 6 degrees field of view (Other lenses available upon

request)

Streaming

 Dual streaming mode (such as different codec/resolution/bit rate and so

on.)

 Burnt-in text supported

 Unicast/Multicast supported

Video/Audio

 Video compression: H.264/MPEG-4/MJPEG,

 Audio compression: G.711(µLaw, aLaw)/PCM

 Analog video out for external monitors

 Video Motion Detection supported

 Two-way mono audio supported

Network

 RTSP/ HTTP protocol supported

 10/100 Base-T Ethernet

Additional Features

 RS-485 support

 USB 2.0 support (Local storage)

 Micro SD card support

 PoE supported

 Built-in Video Content Analysis

 OSD support

 SDK (Software Development Kit) provided

VCA (Video Content Analysis)

 VCA Presence (Included as basic)

 VCA Surveillance (Optional)

RTC Series RTC Installation Guide

01A.04 5

2. PACKAGE CONTENTS

The package contains main camera, DC power adaptor, DC jack adaptor cable,

hex wrench driver, 9 pin terminal block, mounting adaptor, screws, and quick

installation guide. Unpack carefully and handle the equipment with care.

Camera

DC power adaptor

Hex wrench driver

9 Pin terminal block

Mounting Adaptor

Screws

Quick Installation Guide

DC Jack Adaptor Cable

The above contents are subject to change without prior notice.

Note

i

RTC Series RTC Installation Guide

01A.04 6

3. PART NAMES

3.1. Rear View

3.2. Bottom View

⑥

⑤

③

①

②

④

①

⑦

ETHERNET

Micro SD

RESET

LOOP OUT

DC 12V

RS-485

DO DI AUDIO

_

+ C 1 C 1 Out In

Intelligent Thermal Camera

⑧

RTC Series RTC Installation Guide

01A.04 7

1 Analog video out

It is an analog video output port.

2 Reset

Reset switch is used for restarting or resetting the camera as Factory Default

(FD). Refer to the section “5.3.Reset” for more specific information.

3 USB connector

Insert a USB storage device

4 9 pin terminal block for D/I, D/O, audio, and serial communication

Refer to the section “4.1.Connectors” for more specific information.

5 Power Adaptor Connector (DC 12V)

The camera needs a DC12V for power supply. Refer to the section “Power

Adapter Connector (DC 12V)” for more specific information.

The device is polarity sensitive. Incorrect power connection may cause

malfunction or damage to the IP device

6 Micro SD Card socket

It is a memory card slot for local storage.

7 LAN Connector (Ethernet)

This is a RJ45 LAN connector for 10/100 Base-T Ethernet.

When the device is powered on, the orange LED lights up first, and then the

green LED.

LED operation setting:

Both LEDs are off when the device is disconnected from a network. When it is

connected, the orange LED turns into solid light, whereas the green LED

continues to blink. To change the setting, refer to the section

4.5.12. LED

Setting

of the

NVC Web Page User’s Manual.

8 Adaptor for mounting the camera

Mounting adaptor is provided to mount the camera on a bracket or tripod.

Orange LED

Green LED

+

-

Caution

!

RTC Series RTC Installation Guide

01A.04 8

4. CONNECTIONS

The device is polarity sensitive. Incorrect power connection may

cause the device to malfunction or damage the equipment.

Caution

!

DC Jack Adaptor

Cabl

LAN Cable

Analog Video Out

ETHERNET

Micro SD

RESET

LOOP OUT

DC 12V

RS-485

DO DI AUDIO

_

+ C 1 C 1 Out In

Intelligent Thermal Camera

Power Adaptor

RTC Series RTC Installation Guide

01A.04 9

4.1.Connectors

1 9 pin terminal block

2 RS-485

The RS-485 serial port consists of TRX+(RX+) and TRX-(RX-) as following the

following image.

RS-485 Connection

3 Sensor (DI) connection

The camera provides 1 channel D/I. It can be connected to either a voltage type

sensor or a relay type sensor as the following figures. It can be selected by

software.

Input voltage range: 0VDC minimum to 5VDC maximum, Max 50mA

Input voltage threshold: 1.5V

Do not exceed the maximum input voltage or relay rate.

Caution

!

TRX+(RX+)

<RS-485 Application>

+

-

TRX-(RX-)

TX+

TX-

PTZ Device

485 Devices

ETHERNET

Micro SD

RESET

LOOP OUT

DC 12V

RS-485

DO DI AUDIO

_

+ C 1 C 1 Out In

Intelligent Thermal Camera

RTC Series RTC Installation Guide

01A.04 10

4 Alarm (DO) connection

Only the relay type is supported.

Relay Rating: Max 24VDC 50mA

Do not exceed the maximum relay rating.

5 Audio connection

The camera has a mono audio input and a mono audio output. As the output

power for the audio is low, amplifier speaker is needed. (Do not use a headphone

or earphone directly to the camera.)

Caution

!

Mic

Ain

Speaker

Aout

DO

COM

Relay Type

Device

Internal

+5V

DI

COM

DI 1

COM

+

-

Relay Type

Voltage Type

+

-

Output of

Sensor

Output of

Sensor

Internal

+

-

RTC Series RTC Installation Guide

01A.04 11

6 Power Adapter Connector (DC 12V)

Power adaptor connector connects to DC Jack adapter cable.

The device is polarity sensitive. Incorrect power connection may

cause the device to malfunction or damage the equipment.

Power Adaptor Connector (DC 12V)

Caution

!

Caution

!

RED

+

-

+

-

RTC Series RTC Installation Guide

01A.04 12

5. CONFIGURATION

5.1.Set up network environment

The default IP address of the device is 192.168.XXX.XXX. Users can identify the

IP address of the device from converting the MAC address’s hexadecimal numbers,

which is attached to the device. Be sure that the device and PC are on a same

area network before running the installation.

5.1.1. Generic IP Environment

In case of generic private network environment where IP address

192.168.XXX.XXX are used, users may view the live streaming images on a web

page using the device’s default IP address:

1. Convert the device’s MAC address to the IP address. Refer to the Hexadecimal-

Decimal Conversion Chart at the end of the manual.

(The MAC address of the device is attached on the side or bottom of the

device.)

2. Start the Microsoft® Internet Explorer web browser and enter the address of

the device.

3. Web streaming and device configurations are supported through ActiveX

program. When the ActiveX installation window appears, authorize and install

the ActiveX.

MAC address = 00-13-23-01-14-B1 → IP address = 192.168.20.177

Convert the last two set of hexadecimal numbers to decimal numbers.

RTC Series RTC Installation Guide

01A.04 13

5.1.2. Custom IP Environment

IPAdminTool and the manual can download from www.rivatech.de homepage.

IPAdminTool is a management tool, which automatically scans all of the network

products for users to perform administrative tasks, which includes network

configurations, firmware update, device reboot, and device organizations.

To modify the device’s default IP address for customized network area;

1.Find the device from the IPAdminTool’s list and highlight the device’s name.

2.Right-click the mouse and select “IP Address”; IP Setup window appears.

3.In the IP Setup’s window, information under ‘Local Network information’ displays

the user/PC’s network area information. Those information need to be

incorporated to the IP Address, Subnet Mask, Gateway, and DNS boxes, except

the last 2 sets of IP Address, which are to be the unique numbers for the device.

Refer to the image above for the setting

4. Click ‘Setup’ to complete the modification.

PC environment Info

Give new unique IP

address in last two sets

RTC Series RTC Installation Guide

01A.04 14

5.2. View video on web page

Once the device has the proper IP address, users can view the live streaming

images through a web browser. ActiveX needs to be installed in Microsoft

Internet Explorer.

1. Type the correct IP address in the Microsoft® Internet Explorer

2. Grant the web browser’s AxAll.cab ActiveX setup and proceed with

installations.

RTC Series RTC Installation Guide

01A.04 15

Caution

!

Caution

!

3. Follow the instructions of the dialog boxes and complete the installation. Once

the installation is complete, start the web browser again and check if video

stream is displayed in the main view frame.

If “

This software requires the Microsoft XML Parser V6 or higher.

Please download MSXML6 from the Microsoft website to continue.

Error code: Cannot create XMLDOMDocument.

” message appears,

download and install the Microsoft Core XML Services (MSXML)

6.0.

5.2.1. View video using IPAdmin Tool

IPAdminTool automatically searches all activated network encoders and IP

cameras and shows the product name, IP address, MAC address and etc.

IPAdminTool and the manual can download from www.rivatech.de homepage.

1. From the IPAdminTool’s product list, select the device by highlighting it.

2. Right-click the mouse and select web-view

3. The system’s default web browser opens the device’s address.

Whether directly accessing the streaming video through typing IP

address on a web page or taking steps through IPAdminTool, the

ActiveX is needed to be installed for the Microsoft® Internet

Explorer to have the complete configuration privileges.

RTC Series RTC Installation Guide

01A.04 16

5.3. Reset

Reset can be carried out as follows:

1. Use a pointed object to push the reset button for 1~2 seconds.

2. Wait for the system to reboot.

5.4. Factory Default

Resetting the device to the factory default will reset all configured parameters to

the initial factory settings. To perform the Factory Default settings:

1. Use a pointed object to push the reset button and hold for 5 seconds. The

orange LED turns off while green LED flashes.

2. Once the green LED becomes solid, release the reset button.

3. Wait for the system to reboot.

The factory default settings are:

IP address: 192.168.xx.yy

Network mask: 255.255.0.0

Gateway: 192.168.0.1

User ID: root

Password: pass

RTC Series RTC Installation Guide

01A.04 17

APPENDIX (A): SPECIFICATIONS

Summary

Camera Module

Camera

Module

Focal

Plane

Array

17 ㎛ Next Generation Mirobolometer Technology

Effective

Pixels

320(H)x240(V)

Scanning

system

Progressive Scan

Spectral

Reponse

8~14 ㎛

Lens

(optional)

7.5mm, F1.4 (42.1 Degree FoV)

16.7mm, F1.2 (18.7 Degree FoV)

25mm, F1.2 (12.4 Degree FoV)

35mm, F1.2 (8,9 Degree FoV)

50mm, F1.2 (6.2 Degree FOV)

Other Lenses available upon request

NEDT

Less than 50mK

Electrical Characteristics

Analog Video Output

1Vp-p, 75Ω

Audio Input

Linein, 1.43Vp-p(Min 1.35Vp-p, max 1.49 Vp-p), 39

KΩ

Audio Output

Lineout, 46mW Power, 16 Ω

Sensor(D/I)

Max 50mA@5VDC, TTL level 1.5V threshold

Alarm(D/O)

Max 50mA@24VDC

On-state resistance: 50 Ω (max continuous)

Power Source

DC 12V / PoE IEEE802.3af(class 0)

Power Consumption

(Approx.)

6~8W(DC 12V)

Video

Compression Format

H.264, MPEG-4, MJPEG Selectable per Stream

Number of Streams

Dual Stream, Configurable

Resolution

Sensor is 320x240, Image can be scaled from QCIF to

D1

Compression FPS

9Hz or 30Hz Models Available

Motion Detection

Supported (DSP)

Burnt-in Text (Digital)

Supported (DSP)

Output

1 Loop Out (BNC connector)

Audio

RTC Series RTC Installation Guide

01A.04 18

Input / Output

1/1 channel

Compression Format

G.711

Function

Digital Input / Ouput

1/1 channel

RS-485

Supported

Network

10/100 Base-T

Protocol

TCP/IP, UDP/IP, HTTP, RTSP, RTCP, RTP/UDP,

RTP/TCP,

SNTP, mDNS, UPnP, SMTP, SOCK, IGMP, DHCP,

FTP, DDNS, SSL v2/v3, IEEE 802.1X, SSH, SNMP

v2/v3

USB 2.0

Supported (Mini-B plug)

SD Slot

Supported (Micro SD)

※ Micro SD Card not included

Environment Condition

Operating

Temperature (indoor)

0 ˚C ~ 50 ˚C (32˚F ~ 122 ˚F)

Operating

Temperature (outdoor)

ODE-1000T-PoE: -20 ~ 50℃

ODE-1000T-230: -40 ~ 50℃

*Cold start: 0 ˚C

Operating Humidity

Up to 85% RH

Mechanical Condition

Material

Aluminum Die Casting-2

Color

Grey

Dimension

65(W) x 65(H) x 114.2(D) mm

Weight (Approx.)

300 g

RTC Series RTC Installation Guide

01A.04 19

APPENDIX (B): THEORATICAL

DISTANCE

Lens

Vehicle

Human

Detect

Recognize

Identify

Detect

Recognize

Identify

7.5mm

491

125

62

170

43

22

14.5mm

955

243

122

338

84

42

25mm

1560

405

202

565

140

70

35mm

2150

560

280

780

190

97

50mm

2600

700

350

1000

250

128

Unit: meter

Please Note!: Released distance are based on theoretical calculation. In practical

application reached distance can diverse depending environment conditions.

RTC Series RTC Installation Guide

01A.04 20

APPENDIX (C): POWER OVER

ETHERNET

The Power over Ethernet (PoE) is designed to extract power from a conventional

twisted pair Category 5 Ethernet cable, conforming to the IEEE 802.3af Power-

over-Ethernet (PoE) standard.

IEEE 802.3af allows for two power options for Category 5 cables.

The IEEE 802.3af-2003 standard allows up to 15.4 W power to device.

However, 12.95W is the maximum available power, as some power gets lost in

the cable.

PoE has advantages over conventional power in such places where AC powers

cannot be reached or expensive to wire.

Note: For proper activation of 12V PoE, the Category 5 cable must be shorter

than 140m and conform the PoE standard.

PoE compatibility

With non-Power Sourcing Equipment (PSE)

When it is connected with non-PSE, the power adaptor should be used.

With power adaptor

Connecting both PSE and power adaptor do not cause any harms to the

products. Disconnecting power adaptor while it is operating does not stop

operation. The product continues to work without rebooting.

Power classification

The PoE Power Class supported by the IP device is Class 0.

Class

Usage

Minimum Power Levels

Output at the PSE

Maximum Power Levels

at the Powered Device

0

Default

15.4W

0.44 to 12.95W

Page is loading ...

Riva RTC series Installation guide

This manual is also suitable for

Riva RTC series Installation guide

Related papers

Other documents