2. SECOP
  3. 105N9518
105N9518

SECOP 105N9518 Operating instructions

  • I've reviewed the instructions for the Secop Gateway 105N9518. It's a communication interface that supports both transistor and LIN communication modes for Secop compressors. The document also includes details about the package contents, installation of the necessary drivers and the dimensions of the gateway. I'm ready to answer any questions you may have about this device.
  • What does the Secop Gateway 105N9518 package contain?
    What are the two communication modes offered by Secop Gateway 105N9518?
    How do I switch to LIN mode with this device?
    What should be done before using the Secop Gateway?
February 2022 DES.I.101.R2.02 / 520N0131 1/2
approx. 1500 mm
approx. 1500-1800 mm
8673-5
1
2
compressors
c
c
BD
DLV
NLV
ompressor
ompressor
compressor
SLVE
2
1
Instructions
Secop Gateway 105N9518
USB
8676-5
3
1
2
Comm.
USB-C
U+* D/I
C
U
C
1
2LIN
BAT
www.secop.com
Made in Germany
* Don‘t connect when
using D/I on BD-Products
Secop Gateway
105N9518
V01.02
Gateway 105N9518 package contains:
Pos. Description
1 USB 2.0 A/C cable
2Gateway communication (Comm.)
cables for various Secop compressor series/controllers
3Secop Gateway
Length, Height: 35 mm / Width: 64 mm / Depth: 58 mm
Please install the latest Virtual COM Port Driver
from Future Technology Devices International Ltd.:
www.ftdichip.com
2/2 DES.I.101.R2.02 / 520N0131 February 2022
Secop accepts no responsibility for possible errors in catalogs, brochures, and other printed material. Secop reserves the right to alter its products without notice. This also applies to products already on order
provided that such alterations can be made without subsequential changes being necessary to specications already agreed. All trademarks in this material are the property of the respective companies. Secop and
the Secop logotype are trademarks of Secop GmbH. All rights reserved. www.secop.com
Instructions
Secop Gateway 105N9518
USB-C
U+* D/I
C
U
C
1
2LIN
BAT
www.secop.com
Made in Germany
* Don‘t connect when
using D/I on BD-Products
Secop Gateway
105N9518
V01.02
USB
8676-6
Comm.
Reserved for
future BD-Products
USB-C
U+* D/I
C
U
C
1
2LIN
BAT
www.secop.com
Made in Germany
* Don‘t connect when
using D/I on BD-Products
Secop Gateway
105N9518
V01.02
USB
8676-7
Comm.
Secop BD-Series Compressor Connection Secop DLV, NLV, SLVE Compressor Connection
The new Secop Gateway 105N9518 replaces the 105N9501 interface. It is fully compatible with all
existing Secop electronic units (controllers) featuring a communication interface.
It oers two communication modes: Secop transistor interface mode (I, D/I or COM pin name) as
well as a full LIN interface (LIN pin name). The mode is selected by connecting or not connecting
the U+ / UBAT pin. When U+ / UBAT is connected to a battery, the unit will switch to LIN mode.
BD-Series Compressors:
U+ / UBAT should only be connected when using a BD controller equipped with LIN.
On BD controllers equipped with a communication line labeled I, D/I or COM, the U+ / UBAT pin
shall not be connected.
/