5008-CH-CL-MWP

Crystorama 5008-CH-CL-MWP User manual

  • Hello! I've reviewed the assembly instructions for the CRYSTORAMA Chandelier 5008-CH-CL-MWP. This document guides you through the step-by-step process of putting together the chandelier, including installing the arms, crystals, and using the appropriate candelabra bulbs. I'm ready to answer any questions you may have about the assembly or the fixture itself.
  • What type of bulbs does this chandelier require?
    What is the recommended wattage for the bulbs?
    Is this fixture rated for wet locations?
ASSEMBLY INSTRUCTION MODEL #5008- CH-CL-MWP
LIGHTING THE WAY FOR SIXTY YEARS
WARNING:
Electrical Danger
Turn Power Off
You will need 8- Candelabra Base Bulb
40 Watts recommended 60 Watts Max.
USE LED BULBS FOR EXTENDED USE
All electrical components must be
installed by a licensed electrician
in accordance with the National
Electric Code and the appropriate
local elecrical codes
A
G
E
F
H
IE
B
DC
The fixture is Dry rated
WARING:This product can expose you to Lead,
which is known to the State of California to cause cancer
and/or birth defects or reproductive harm.For more
information go to www.p65warnings.ca.gov
A. 8 Sets. (2)14mm + AS9-2"
B. 8 Sets. (1)Ring + (1)14mm + (1)Square
C. 16 Sets. (18)14mm
D. 8 Sets. (7)14mm + AS9-2"
E. 45 Sets. (1)14mm + AS9-2"
G. 1 Piece. (2)14mm + AS8-40mm Ball
F. 8 Sets. (10)14mm
Crystal Sets
I. 8 Sets. (1)Ring + (1)Square
H. 8 Sets. (1)14mm + AS9-3"
27"
HOW TO INSTALL:
Place the fixture parts on a soft cloth-covered platform
before installation of fixture.
1. Screw the Center column kit onto the distributor kit.
2. Place the bottom bowl, check ring, bobeche, check ring,
in that order,over the bottom distributor box.
Secure with the finial.
3. To install the glass arms, slightly loosen each screw on
the top plate over the distributor box. Pull a female
plug through a hole in the plate.Connect the male plug
at the end of the arm with the female plug that was
just pulled.
Push the end of the arm with the metal tab through the
hole until stopped by the metal tab(this should also
push the wires and plugs back inside the metal plate).
Twist the metal tab counter-clock wise until both inserts
lock onto the loose screws.
Tighten the screw securing the arm in place.Repeat for
all arms.
4. Insert the scrolls onto the holder and Put the bobeche
over the socket.
5. Attach the mounting bar onto the outlet box.
7. Raise the fixture up and do the wire connection.
Attach the canopy over the mounting bar and secure
with collar ring.
8. Dress the crystals as illustrated.
6. Decide the desired hanging height and adjust the chain
to the correct length.
DETAILED ILLUSTRATION
(1)Bobeche with Ex5
102"
27"
PART NUMBER MODEL #5008- CH-CL-MWP
Part Number
Outlet Box
A
BC
DF
E
H
I
G
J
K
M
L
N
O
P
Q
S
R
LIGHTING THE WAY FOR SIXTY YEARS
Part Numbers
C. (1)-Lock Washer
D. (1)-Hex Nut
A.(2)-Wire Connector
K. (1)-Center Column Kit
Top Bobeche;Ø6",8pin,14mm center hole.
-XSN5008CHBOB8PN
Glass Vase ; H8"
Metal Cover ; H1 2/8"
B. (1)-Mounting Bar
N.(8)-10"Arms-XSN500CHARM10INKD
O. (8)-6"Scrolls-XSN5008CHSCR
E. (1)-Nipple
F.(1)-Canopy (W5"xH1")-XSN5008CHCAN5IN
G. (1)-Collar Ring
H. (1)-Collar Loop
I. (1)-Chain(4mmx72")-XSN5008CHCHA4MM
M. (9)-Bobeche ; Ø5",5 pin,24mm center hole.
-XSN5008CHBOB5IN
Q. (8)-Female Plug
R. (1)-Distributor Kit
Coupling.
Metal Bowl.
Center Bowl ; Ø6",no pin,13mm center hole.
Glass Vase; H6"
Distributor Box.
Thread.
S. (1)-Bottom Bowl; Ø6",no pin,13mm center hole.
T. (2)-Check Ring ; Ø1 3/8"
U. (1)-Finial-XSN5008CHFIN
L. (8)-PVC Candle Sleeve
Arm with
Metal tab
Screws
Plate
Male Plug
Female Plug
P. (8)-Holder
T
J. (1)-Center Column Kit Loop
T
U
M
/