2. SUNCO
  3. ARCADIA 4-BULB
ARCADIA 4-BULB

SUNCO ARCADIA 4-BULB User manual

  • Hello! I've reviewed the installation manual for the Sunco ARCADIA 4-BULB Ceiling Light. This manual includes detailed steps for hardwiring the fixture, safety warnings, and parts included. I'm ready to answer any questions you have about the installation process or the fixture's features.
  • What tools are required for installation?
    What type of bulbs does the fixture use?
    What is the warranty period for this product?
    What is the voltage of the fixture?
    What material is the housing made of?
WARNING SPECIFICATIONS
Voltage
Warranty
.W x
Steel
2.77 lbs
V
5 Years
Housing Material
Weight
Wattage
To reduce the risk of fire, electric shock, or physical injury:
• This product should be installed in accordance with regional and local laws or
regulations by a person familiar with the construction and operation of the product
and the hazards involved.
• Check for shipping damage prior to install. If the product is damaged, do not use it.
• Turn off the switch and circuit breaker before installing this light fixture.
• Proper grounding is required to ensure safety.
• This fixture is not suitable for wet environments.
• Do not install directly over a heat source (stove, etc.).
• This fixture should not be installed on a radiant heating ceiling or on the surface of
combustible material, nor should this light be covered by flammable material.
• Use safety precautions. Safety eyeglasses and gloves are recommended.
EASY INSTALLATION
1. Turn off circuit breaker that provides
power to light switch.
2. Run source wire from existing outlet to
switch location, if needed.
3.3. Install compatible junction box (not
included.)
• Slot distance for junction box should
be 1.65” - 3.54” (42mm-90mm)
4. Remove x2 ball nuts and their gaskets
from mounting bracket.
5. Using x2 provided screws, install mounting
bracket onto junction box.
10. Install x4 light bulbs with an E26 base. 11. Turn on circuit breaker and test light.
6. Feed supply wires through junction box.
7. Connect supply wires to fixture wires with
included wire nuts.
• Black to Black
• White to White
• Ground to Ground
8. Tuck all wires into junction box.
9. Attach ceiling fixture to mounting bracket
with ball nuts and gaskets. Rotate
fixtureinto place.
ARCADIA BULB
CEILING LIGHT
COMPONENTS
Required Tools: Screwdriver, Ladder, Wirestripper
A19 Filament
Bulbs
x4
Wire Nuts
x3
Installation Manual
Hardwire Installation with Bracket to Junction Box
Screws
x2
Mounting
Bracket
x1
ON
OFF
13.9”
3.7”
Turn Power OFF
Wire nut
A19
Filament
Bulbs
Ball nut
Ball nut
Screw
FCC NOTES (A19 FILAMENT BULBS)
• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.
• Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
/