Sunco Lighting Sputnik LED Ceiling Light Installation guide

Brand: Sunco Lighting

Model: Sputnik LED Ceiling Light

Type: Installation guide

Sunco Lighting Sputnik LED Ceiling Light features a modern, geometric design that complements any décor. With its energy-efficient LED bulbs, this light fixture provides bright, long-lasting illumination. The adjustable arms allow you to customize the look and direct the light where you need it most. Perfect for living rooms, bedrooms, dining rooms, and more, this ceiling light is easy to install and backed by a 7-year warranty.

BULB SPECIFICATIONSFIXTURE SPECIFICATIONS

VoltageVoltage

WarrantyWarranty

8.5E

WetDamp

GlassSteel

0.11 lbs2.55 lbs



7 Years7 Years

Moisture RatingMoisture Rating

Housing Material Housing Material

WeightWeight

WattageBase

EASY INSTALLATION

1. Turn off power at fuse or circuit breaker

before installing.

2. Install junction box (not included).

3.3. Remove screw caps from mounting

bracket and set aside.

4. Secure mounting bracket onto junction

box using (2) provided screws.

8. Connect (4) white fixture wires to white

wire connector. Connect (4) black fixture

wires to black wire connector.

9. Connect supply wires to fixture wires with

included wire nuts.

- Black to Black

- White to White

- Ground to Ground

5. Insert (2) short tubes and (2) long tubes

into Lamp Bracket as shown.

6. Using wrench, hex nuts, and lock washers,

secure short tubes to canopy first.

7. Repeat with (2) long tubes.

SPUTNIK LED

CEILING LIGHT

COMPONENTS

10. Use screw caps to secure canopy to

mounting bracket.

11. Install (4) E26-base light bulbs.

12. Turn on circuit breaker and test light.

Required Tools: Screw Driver

Mounting

Bracket

Hex

Nuts

Screws

Wire

Nuts

Lock

Washers

Wrench

Installation Manual

Hardwire Bracket to Junction Box

Turn Power ON

OFF

Turn Power OFF

OFF

ON Mounting

Screws

Lamp Bracket

Long Tube

Short Tube

Hex

Nuts

Lock

Washers

Canopy

White

Wires

Black

Wires

Wire

Nuts

Screw Caps

WARNING

FCC NOTES

To reduce the risk of fire, electric shock, or physical injury:

• This product should be installed by a person familiar with the construction and operation of the product and the hazards involved.

• Abide by regional and local laws or regulations.

• Check for shipping damage prior to install. If the product is damaged, do not use it.

• Turn off the switch and circuit breaker before installing this light fixture.

• Proper grounding is required to ensure safety.

• This fixture is not suitable for wet environments

• This fixture should not be installed directly over a heat source, on a radiant heating ceiling, or on the surface of combustible material, nor should this light be

covered by flammable material.

• Use safety precautions. Safety eyeglasses and gloves are recommended.

• Sunco Lighting does not warrant the compatibility of this fixture with any bulbs or products other than the ones provided.

• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause undesired operation.

• Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

— Consult the dealer or an experienced radio/TV technician for help.

Sunco Lighting Sputnik LED Ceiling Light Installation guide

Sunco Lighting Sputnik LED Ceiling Light Installation guide

Sunco Lighting Sputnik LED Ceiling Light Installation guide

Other documents