Global Sources TB-2035 User manual

TB-2035 Manicure/Pedicure Nail Set

Instruction Manual

Safety Instructions

※Important Notice: This manual is available in two languages: English and Simplified

Chinese. If any dispute or confusion arises caused by the translation, the English version shall

prevail.

※To ensure proper operation of this device, please read this instruction manual carefully

before using the device and keep it for further reference.

The following persons should not use this device: children; persons with skin

inflammation in the fingers or toes; persons with allergies; persons with reduced

physical, sensory, or mental capabilities.

Please verify the device before you start using it. Do not use this device if you detect

any damage or malfunction to prevent injury.

Immediately discontinue use if you detect any malfunction or abnormality while

using this device.

Do not attempt to modify, disassemble, or repair the device by yourself (except

detachable parts) to prevent accidents.

Use this device for its intended purpose only and as directed in this instruction

manual. Do not use this device for any other purpose than nail care.

Do not leave the device in a humid or hot place.

Do not share the same device with others.

Regularly clean the device and the accessories to extend its lifetime.

Keep the device out of reach of children.

If you do not intend to use the device for an extended period of time, remove the

battery.

1. Device Specifications

Name: Manicure/Pedicure Nail Set

Model No.: TB-2035

Power: 1.5V /0.5W

Type of Battery: AAA 1.5V x 1 (Not Included)

Executive Standard: Q/XMMJ1006-2020

2. Device Description

1) Felt Cone Head

2) White Filing Head

3) Emery Grinding Head

4) ON/OFF Switch

5) Protective Cap

6) Battery Compartment Cover

3. Certification Marks

4. How to Use the Device

To ensure the correct operation of this device, please read the instructions carefully before

use.

1. Inserting the Battery

Make sure the device is switched off before you install the battery. Use both hands to

remove the battery compartment cover. Hold the upper part of the device with one hand,

with the other hand hold the battery compartment cover, and pull firmly to remove it (do

not slide the on/off switch accidentally during this process). Insert one AAA battery

according to the correct polarity (positive and negative), as indicated in the battery

compartment. (Picture 2)

2. Choose the attachment according to your needs and push it firmly into the connection

shaft until it’s securely in place.

Emery Grinding Head: Use the emery grinding head to remove dead skin on the sides of

natural nails and to buff the edge of the nails. (Picture 3)

White Filing Head: Use the head attachment to polish the edge of acrylic nails and the

surface of natural nails. This will make the connection between the nail polish and the nail

surface smoother. (Picture 4)

Felt Cone Head: This attachment polishes the nails leaving a glossy and smooth surface.

(Picture 5)

3. After installing the head attachment, push the sliding on/off switch upwards to ON to

switch the device on. (Picture 6)

4. After use, push the sliding on/off switch downwards to switch the device off. The device

has an internal storage area for the attachments. Store the attachments in the storage area

after use. (Picture 7)

5. Cleaning & Maintenance

Make sure the device is turn off before you start cleaning.

Do not immerse the device in water. You can clean the attachment heads

separately.

Clean the device surface with a clean slightly wet cloth.

Never use lubricants, detergents, polishing agents, or air fresheners on this device.

6. Storage

Do not leave the device in a wet or humid place. If you do not intend to use the device for an

extended period of time, remove the battery and store the device properly.

7. Recycling

Batteries may contain substances harmful to the environment. Before disposing of this

device, remove the battery. Do not dispose of this device and battery together with the

domestic waste. Instead, hand them over to an official recycling point to contribute to

environmental protection.

8．Warranty & Support

Troubleshooting

Problem

Possible Cause

Solution

Abnormal noise.

The head attachment is

installed incorrectly.

Install the head attachment

correctly as guided.

The device is not working

The battery is low.

Replace the battery.

normally.

The battery is out of power.

The battery is installed

incorrectly.

Remove the battery and install it

correctly as guided.

Global Sources TB-2035 User manual

Other documents