Kessil DMX Track User guide

DMX Track
Brand
Kessil
Model
DMX Track
Type
User guide

Kessil DMX Track is a versatile lighting system that offers precise control over your lighting setup, enabling you to create dynamic and immersive lighting effects. With its individual power circuits, you can manage multiple lighting fixtures independently, maximizing flexibility and energy efficiency. Seamlessly integrate DMX control via XLR5, RJ45, or TRRS connectors, ensuring compatibility with various DMX lighting controllers. The system's rugged design and easy installation make it suitable for various applications, including architectural, corporate, and fixed installations.

Kessil DMX Track is a versatile lighting system that offers precise control over your lighting setup, enabling you to create dynamic and immersive lighting effects. With its individual power circuits, you can manage multiple lighting fixtures independently, maximizing flexibility and energy efficiency. Seamlessly integrate DMX control via XLR5, RJ45, or TRRS connectors, ensuring compatibility with various DMX lighting controllers. The system's rugged design and easy installation make it suitable for various applications, including architectural, corporate, and fixed installations.

Track End Feed Wiring Guide
05262022A
Please refer to the listed QR Code/Links for detailed step-by-step instructions for the wiring cable per
installation requirements. Contact [email protected] for more information.
• Disconnect electrical power before adding to or changing the configuration of the track.
• Do not install this track in damp or wet locations (IP20 , 45°C max).
• Do not install any part of a track system less 5 ft. above the floor.
• Check with a qualified electrician prior to any installation.
• Do not attempt to energize anything other than lighting track fixtures on the track.
• In order to reduce the risk of fire and electrical shock, do not attempt to connect power tools, extension
cords, appliances and the like to the track.
• Do not slide light fixtures along track when relocating. Always remove fixture/adapter from track.
• Before reinstalling in new location, make sure to properly secured adapter back in track.
VIDEO LINKS
Wire Power to
End Feed
Wire DMX to
End Feed via XLR5
Wire DMX to
End Feed via RJ45
Wire DMX to
End Feed via TRRS
Link to Video Link to Video Link to Video Link to Video
Track End Feed Wiring Guide
STEP-BY-STEP INSTRUCTIONS
READ AND SAVE ALL INSTRUCTIONS
1689 Regatta Blvd. Richmond, CA 94804 | [email protected] | (510) 620-5250
Each End Feed component has two (2) sets of 20A-max conductors for two (2) individual power circuits.
Link to Video
Line drawing of power splicing on End Feed
End feed Component with pin-outs
Legend
A 233 Series, 2 Circuit 120V Track
B Securing screw for end feed component
C DMX/Data conductor entry
D Power conductor entry for Circuit 1 and Circuit 2
A
B
C
D
DATA (DATA WIRE)
GROUND (GROUND WIRE)
N1 (NEUTRAL WIRE)
L1 (HOT WIRE)
GIRCUIT 1GIRCUIT 2
EACH CIRCUIT CAN HANDLE
A MAXIMUM CURRENT OF
20 AMPS
Track End Feed Wiring Guide
Wire Power to End Feed
1689 Regatta Blvd. Richmond, CA 94804 | [email protected] | (510) 620-5250
DMX signal requires 2 signal carriers and the polarity of the DMX conductors are labelled on the sticker
located on the end feed component.
DMX Polarity Label Sticker
DMX Conductors wired to End Feed
Track End Feed Wiring Guide
Wire DMX to End Feed
1689 Regatta Blvd. Richmond, CA 94804 | [email protected] | (510) 620-5250
Standard DMX Cabling and Polarity
Sleeve
Ring 2
Ring 1
Tip
Link to Video
Connector
Description
Connector
Pin-out
Ground
Data -
Data +
Video Guide
XLR5
DMX lighting standard Architectural, corporate,
and fixed installations
Fiilex DMX Controller,
P360 Pro and P360 Pro Plus.
Link to Video
RJ45
Link to Video
TRRS
1
2
3
7 ,
2
1
Tip
Ring1 (closest to tip)
Sleeve
1
2
3
#7&8
#2
#1
Signal
Track End Feed Wiring Guide
Wire DMX to End Feed Continued
1689 Regatta Blvd. Richmond, CA 94804 | [email protected] | (510) 620-5250
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Kessil DMX Track User guide

DMX Track
Brand
Kessil
Model
DMX Track
Type
User guide

Kessil DMX Track is a versatile lighting system that offers precise control over your lighting setup, enabling you to create dynamic and immersive lighting effects. With its individual power circuits, you can manage multiple lighting fixtures independently, maximizing flexibility and energy efficiency. Seamlessly integrate DMX control via XLR5, RJ45, or TRRS connectors, ensuring compatibility with various DMX lighting controllers. The system's rugged design and easy installation make it suitable for various applications, including architectural, corporate, and fixed installations.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents