Bradley Corporation S19-310FW User guide

Bradley Corporation
Brand
Bradley Corporation
Model
S19-310FW
Category
Sanitary ware
Type
User guide
S19-310FW
Combination Drench Shower and Eye/Face Wash Unit
© 2015 Bradley
P.O. Box 309, Menomonee Falls, WI 53052-0309
800 BRADLEY (800 272 3539) +1 262 251 6000
bradleycorp.com
Page 1 of 2 1/10/2014
This information is subject to change without notice.
Bradley_SafetyCombi_S19-310FW
•
ComplieswithAmericanNationalStandardZ358.1
•
GalvanizedSteelProtectedwithBradTect
®
SafetyYellowCoating
•
CombinationUnitsmaybeTop-SuppliedorMid-Supplied
•
UniversalIdentificationSignandInspectionTagIncluded
•
Full,One-YearWarranty
• ClassiedbyUnderwritersLaboratoryInc.toANSIZ358.1
• SpinTec
™
showerheadsarecoveredbyoneormoreofthefollowingpatents:8113446;
D594,089;D669,555;Reg.Comm.Des.D001079560-0001.Otherpatentspending.
Specifications
CombinationDrenchShowerandEye/FaceWashUnitsavesspaceandfitseasilyinto
anyworkenvironment.Showervalveoperatesquicklybyapullrodwithatriangular
handle.Showerprovidesasuperiorwashdownwithamoreevenspraypattern.Eye/
facewashoperatedbyalarge,highlyvisiblepushhandle.Safe,steadywaterflowunder
varyingwatersupplyconditionsfrom30–90PSIisassuredbyintegralflowcontrolin
thesprayheadassembly.NOTE:TheANSIZ358.1standardrequiresanuninterruptible
supplyofflushingfluidataminimum30PSIflowingpressure.Eye/facewash
sprayheadscontainanantimicrobialagenttoprotectthesprayheads.
This plumbing fixture is not intended to dispense water for human
consumption through drinking or for preparation of food or beverages.
®
Model S19-310FW
Recommended Option:
Navigator S19-2200 EFX60
Emergency Thermostatic Mixing Valve
Satisfies ANSI Z358.1
tepid water requirements.
Model Description
S19-310FW DrenchShowerandEye/FaceWash-Plastic Showerhead and
Bowl
S19-2200 NavigatorEFX60-EmergencyThermostaticMixingValve
Standard Equipment
SpinTec™ Showerhead
Standardshowerheadis3.1"(78.7mm)diameterhighlyvisibleyellowimpact-resistant
plastic.SpinTecdrenchshowerheadfeaturesintegral22GPMflowcontrol,conserving
waterandhelpingtoaccuratelysizeyourtepidwatersystem.
SpinTec Flow Rate vs Inlet Pressure at Fixture
0
5
10
15
20
25
30
35
40
10 20 30 40 50 60 70 80 90
Inlet pressure at Fixture (psig)
Flow Rate (gpm)
Eyewash Bowl
10"(254mm)diameteryellowimpact-resistantplastic.
Standard Sprayhead Assembly
Twinperforated-disceye/facewashheadswithprotectivesprayheadcovers,operated
byalarge,highlyvisiblepushhandle.Safe,steadywaterflowundervaryingwater
supplyconditionsfrom30–90PSIisassuredbyintegralflowcontrolinthesprayhead
assembly.
Shower Valve
Chrome-platedbrass1"NPTstay-openballvalve.Operatedbyastainlesssteelpullrod
withtriangularhandle.
Eyewash Valve
Chrome-platedbrass½"NPTstay-openballvalvehandoperatedbyhighlyvisiblesafety
yellowPVCpushhandle.
Pipe and Fittings
1¼"galvanizedsteelwithBradTect
®
safetyyellowcoating.
Water Supply
1¼"NPT.
Local codes may require the installation of a backflow prevention valve to
complete proper installation. Compliance with local codes is the responsibility
of the installer. Valve must be tested annually to verify that it is functioning
properly. Backflow prevention valves are not included with the fixture and may be
supplied by the contractor or purchased from Bradley Corporation.
S19-310FW
Combination Drench Shower and Eye/Face Wash Unit
© 2015 Bradley
P.O. Box 309, Menomonee Falls, WI 53052-0309
800 BRADLEY (800 272 3539) +1 262 251 6000
bradleycorp.com
Page 2 of 2 1/10/2014
This information is subject to change without notice.
Bradley_SafetyCombi_S19-310FW
Ø 9" (229mm) Flange
with (3) Ø
3
⁄8" (10mm)
Holes on Ø 8" (203mm)
Bolt Circle
9"
(229mm)
25
3
⁄8"
(645mm)
86"
(2180mm)
to Floor
25½"
(648mm)
Ø 10"
(254mm)
36
3
⁄8"
(924mm)
6½"
(165mm)
10½"
(267mm)
9½"
(241mm)
66"
(1676mm)
to Floor
6"
(152mm)
4½"
(114mm)
Ø 3.1"
(78.7mm)
Top View
From Bowl
All dimensions assume standard thread engagement. Variations in manufacturing allow for +/-
1
⁄8" (3mm) per threaded joint.
To find the tolerance of a dimension, add the number of thread joints in between a dimension and multiply it by
1
⁄8" (3mm).
  • Page 1 1
  • Page 2 2

Bradley Corporation S19-310FW User guide

Bradley Corporation
Brand
Bradley Corporation
Model
S19-310FW
Category
Sanitary ware
Type
User guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents