Altronix ALTV244175ULCB3 Installation guide

Altronix
Brand
Altronix
Model
ALTV244175ULCB3
Category
Electrical enclosures
Type
Installation guide

This manual is also suitable for

ALTV244UL3 Series
CCTV Power Supplies
Installation Guide
Models Include:
• ALTV244UL3 • ALTV244ULCB3
- 24VAC @ 3.5 amp (85VA) - 24VAC @ 3.5 amp (85VA)
or 28VAC @ 3 amp (85VA). or 28VAC @ 3 amp (85VA).
- Four (4) Fuse Protected Outputs. - Four (4) PTC Protected Outputs.
- Factory installed 3-wire line cord. - Factory installed 3-wire line cord.
• ALTV244ULX3
- 24VAC @ 3.5 amp (85VA)
or 28VAC @ 3 amp (85VA).
- Four (4) Fuse Protected Outputs.
- Factory installed 3-wire line cord.
• ALTV244175UL3 • ALTV244175ULCB3
- 24VAC @ 7 amp (175VA) - 24VAC @ 7 amp (175VA)
or 28VAC @ 6.25 amp (175VA). or 28VAC @ 6.25 amp (175VA).
- Four (4) Fuse Protected Outputs. - Four (4) PTC Protected Outputs.
- Factory installed 3-wire line cord. - Factory installed 3-wire line cord.
Rev. 040406
- 2 - ALTV244UL3 Series
Overview:
ALTV244UL3 Series CCTV Power Supplies provide 24VAC or 28VAC distributed via four (4) fuse or PTC protected
outputs for powering CCTV Cameras, heaters and other video accessories.
Four (4) Output ALTV244UL3 Reference Chart:
Altronix
Model Number
Output Voltage
Total Output Current
(Power)
Number of Outputs
PTC Protected Outputs
(Class 2 power-limited
for Dry locations -
Class 3 for Wet locations)
Fuse Protected
Class 1 Outputs
Individual Output Current
(max per output, not to
exceed total output current)
Fuse Ratings
Main Fuse Ratings
Primary In-line Fuse
Ratings
115VAC 60Hz
Input Current
Agency
Listings
ALTV244UL3
24VAC 3.5 amp
4 --- Yes
3.5
amp
3.5
amp
5 amp/
250V
3.5 amp/
250V
0.9
amp
28VAC 3 amp
ALTV244ULX3
24VAC 3.5 amp
4 --- Yes
3.5
amp
3.5
amp
5 amp/
250V
3.5 amp/
250V
0.9
amp
28VAC 3 amp
ALTV244ULCB3
24VAC 3.5 amp
4 Yes ---
2.5
amp
---
5 amp/
250V
3.5 amp/
250V
0.9
amp
28VAC 3 amp
ALTV244175UL3
24VAC 7 amp
4 --- Yes
3.5
amp
3.5
amp
10 amp/
250V
3.5 amp/
250V
1.76
amp
28VAC 6.25 amp
ALTV244175ULCB3
24VAC 7 amp
4 Yes ---
2.5
amp
---
10 amp/
250V
3.5 amp/
250V
1.76
amp
28VAC 6.25 amp
Specifications:
Installation Instructions:
1. Mount unit in a desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws, level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pgs. 7, 8).
Secure enclosure to earth ground.
2. Set power switch on power distribution board marked [PD] to OFF position for models ALTV244UL3,
ALTV244ULX3 or ALTV244ULCB3 (Figs. 1-3, pgs. 4, 5).
Agency Listings:
• ULListedforCommercialCCTVEquipment(UL2044).
CUL Listed - CSA Standard C22.2 No.1-98,
Audio,VideoandSimilarEquipment.
• CEEuropeanConformity.
Input:
• 115VAC,50/60Hz.
Output:
• Four (4) fuse or PTC protected outputs.
• 24VACor28VACoutput.
• Outputs are rated @ 3.5 amp (fused) or 2.5 amp (PTC).
• Surgesuppression.
Features:
• PowerON/OFFswitch(ALTV244UL3,ALTV244ULX3
or ALTV244ULCB3).
Features (cont’d):
• Illuminatedpowerdisconnectcircuitbreaker
with manual reset (ALTV244175UL3,
ALTV244175ULCB3).
• Unitmaintainscamerasynchronization.
• Easeofinstallationsavestime&eliminatescostlylabor.
• Sparefusesincluded(onfuseprotectedmodels).
• Factoryinstalled3-wirelinecord.
Enclosure Dimensions (H x W x D):
• ALTV244UL3,ALTV244ULCB3
8.5” x 7.5” x 3.5” (215.9mm x 190.5mm x 88.9mm).
• ALTV244175UL3,ALTV24175ULCB3
12” x 7.5” x 4.5” (304.8mm x 190.5mm x 114.3mm).
• ALTV244ULX3
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.55mm).
ALTV244UL3 Series - 3 -
3. All units are factory set for 24VAC operation.
For 28VAC operation adjust unit prior to applying power as follows:
Remove wires marked [24V] and [28V] from terminals marked [P] and [S]. Connect wire marked [28V] to
terminal marked [P] and connect wire marked [24V] to terminal marked [S].
Note:ALTV244ULCB3setfor28VACoperationisnotClass2Rated,notpower-limited.
4. Plug in 3-wire line cord (Figs. 1-5, pgs. 4-6).
Keeppower-limited(PTCprotectedoutputsonly)wiringseparatefromnonpower-limitedwiring.
Minimum0.25”spacingmustbeprovided. Useseparateknockouts.
5. Set power switch on power distribution board marked [PD] to ON position for models ALTV244UL3,
ALTV244ULX3 or ALTV244ULCB3 (Figs. 1-3, pgs. 4, 5).
6. Measure output voltage before connecting devices. This helps avoid potential damage.
Terminals marked [1P - 4P] are of the same polarity.
CAUTION:Determinethemaximumoperatingvoltageoftheequipmentbeingpoweredbeforeadjusting
theoutputvoltage.
7. Set power switch on power distribution board marked [PD] to OFF position for models ALTV244UL3,
ALTV244ULX3 or ALTV244ULCB3 (Figs. 1-3, pgs. 4, 5). UnPlug 3-wire line cord for all other models
(Figs. 1-5, pgs. 4-6).
8. Connect devices to terminals marked [1P - 1N through 4P - 4N] on PD4 or PD4CB board (Figs. 1-5, pgs. 4-6),
carefully observing polarity.
9. Set power switch on power distribution board marked [PD] to ON position for models ALTV244UL3,
ALTV244ULX3 or ALTV244ULCB3 (Figs. 1-3, pgs. 4, 5). Plug in 3-wire line cord (Figs. 1-5, pgs. 4-6).
10.GreenLEDwillilluminatewhenpowerispresent.
11. Upon completion of wiring, secure enclosure door with screws (supplied). Installation of cam lock is optional.
Caution:Equipmenttobeinstalled/servicedbyauthorized/trainedpersonnelonly.
Shutbranchcircuitpowerbeforeinstalling/servicingequipment.
WARNING:Toreducetheriskoffireorelectricshock,donotexposetheunittorainormoisture.
Thisinstallationshouldbemadebyqualifiedservicepersonnelandshouldconformtoalllocalcodes
andinaccordancewiththeNationalElectricalCode.Use75˚CorhigherratedULinsulatedwiringfor
connectingtheunittothemains.Replacefuseswiththesametypeandrating(refer to Four (4) Output
ALTV244UL3 Reference Chart, pg. 2)
Terminal Identification:
PD4 - Power Distribution Module
1P - 4P AC output
1N - 4N AC output
Thelightningflashwitharrowheadsymbolwithinanequilateraltriangleisintendedtoalerttheusertothe
presenceofaninsulatedDANGEROUSVOLTAGEwithintheproduct’senclosurethatmaybeofsufficient
magnitude to constitute an electric shock.
Theexclamationpointwithinanequilateraltriangleisintendedtoalerttheusertothepresenceofimportant
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTION: To reduce the risk of electric shock do not open enclosure. There
arenouserserviceablepartsinside.Referservicingtoqualifiedservicepersonnel.
- 4 - ALTV244UL3 Series
Fig. 1
ALTV244UL3
1P 1N 2P 2N 3P 3N 4P 4N
LED
3.5A 250V
3.5A 250V
3.5A 250V
XFMR
White
Lead
Black
Lead
Black
Lead
non-power
limited
non power-
limited
115VAC
Input
50/60 Hz.
ON OFF
SW1
INPUT
NP S
Green
Lead
(Ground)
MAIN FUSE
Primary
In-line
Fuse
Class 1 Outputs
24VAC or 28VAC
output 1 (Follow
same procedure
using terminals
2P & N through
4P & N outputs
2 through 4)
BackPanel
ofEnclosure
F1 F2 F3 F4
INPUT
1P 1N 2P 2N 3P 3N 4P 4N
LED
ON OFF
SW1
NP S
MAIN FUSE
XFMR
White
Lead
Black
Lead
Black
Lead
non-power
limited
non power-
limited
115VAC
Input
50/60 Hz.
Green
Lead
(Ground)
Primary
In-line
Fuse
24VAC configuration Class 2 Not Wet/Class 3 Wet
28VAC configuration Class 1
24VAC or 28VAC
output 1
(Follow same
procedure using
terminals 2P & N
through 4P & N
outputs 2 through 4)
Fig. 2
ALTV244ULCB3
BackPanel
ofEnclosure
ALTV244UL3 Series - 5 -
Fig. 3
ALTV244ULX3
1P 1N 2P 2N 3P 3N 4P 4N
LED
3.5A 250V
3.5A 250V
3.5A 250V
ON OFF
SW1
INPUT
NP S
MAIN FUSE
Door
115VAC
50/60Hz Input,
0.9 amp
Black
Lead
White
Lead
XFMR
AC Input and protected outputs must leave cabinet through
separate knockouts.
0.25" spacing must be provided between AC Input and low voltage wiring.
For suppl
y
connection use wire rate for at least 90˚C.
Class 1 outputs
non power-limited
Primary In-line
Fuse
24VAC or 28VAC fused ( Follow same
procedure using terminals 2P & N thru 4P & N
outputs 2 thru 4).
- 6 - ALTV244UL3 Series
XFMR
Black
Lead
non-power
limited
115VAC Input
50/60 Hz.
Green
Lead
(Ground)
White
Lead
Class 1 Outputs
24VA C or 28VAC
output 1 (Follow
same procedure
using terminals
2P & N through
4P & N outputs
2 through 4)
Illuminated Power Disconnect
Circuit Breaker with manual reset
Fig. 4
ALTV244175UL3
INPUT
NPS
MAIN FUSE
non-power
limited
Green
Lead
(Ground)
24VAC configuration Class 2 Not Wet/Class 3 Wet
24VAC or 28VAC
output 1
(Follow same
procedure using
terminals 2P & N
through 4P & N
outputs 2 through 4)
Illuminated Power Disconnect
Circuit Breaker with manual reset
XFMR
Black
Lead
115VAC Input
50/60 Hz.
White
Lead
Fig. 5
ALTV244175ULCB3
Fig. 5a
Fig. 4a
ALTV244UL3 Series - 7 -
1.25”
(31.75mm)
0.5”
(12.7mm)
0.5”
(12.7mm)
1.5”
(12.7mm)
1.25”
(31.75mm)
1.5”
(12.7mm)
3.5”
(88.9mm)
3.5”
(88.9mm)
3.5”
(88.9mm)
1”
(25.4mm)
1”
(25.4mm)
5.75”
(146.05mm)
1”
(25.4mm)
1.13”
(28.7mm)
5.88”
(149.35mm)
0.88”
(22.35mm)
0.88”
(22.35mm)
1.11”
(28.19mm)
1.11”
(28.19mm)
4.5”
(114.3mm)
4.5”
(114.3mm)
4.5”
(114.3mm)
4.5”
(114.3mm)
7.5”
(190.5mm)
7.5”
(190.5mm)
2.5”
(63.5mm)
12”
(304.8mm)
12”
(304.8mm)
1.25”
(31.75mm)
1.25”
(31.75mm)
1.25”
(31.75mm)
1.125”
(28.575mm)
1”
(25.4mm)
1”
(25.4mm)
1”
(25.4mm)
5.25”
(133.35mm)
6.05”
(153.67mm)
6.05”
(153.67mm)
3.5”
(88.9mm)
3.5”
(88.9mm)
7.25”
(184.15mm)
2”
(50.8mm)
2”
(50.8mm)
8.125”
(206.375mm)
0.6”
(15.24mm)
1”
(25.4mm)
1”
(25.4mm)
0.6”
(15.24mm)
0.6”
(15.24mm)
1.125”
(28.575mm)
0.6”
(15.24mm)
3.625”
(184.15mm)
Enclosure Dimensions (H x W x D) for:
• ALTV244175UL3
• ALTV244175ULCB3
12” x 7.5” x 4.5” (304.8mm x 190.5mm x 114.3mm)
Enclosure Dimensions (H x W x D) for:
• ALTV244UL 3
• ALTV244ULCB3
8.5” x 7.5” x 3.5” (215.9mm x 190.5mm x 88.9mm)
- 8 - ALTV244UL3 Series
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056
web site: www.altronix.com, e-mail: [email protected], Lifetime Warranty, Made in U.S.A.
IIALTV244UL3Series J11M
Enclosure Dimensions (H x W x D) for:
• ALTV244ULX3
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.55mm)
1.40”
(36mm)
1.40”
(36mm)
4.85”
(123mm)
4.85”
(123mm)
1.40”
(36mm)
1.40”
(36mm)
5.10”
(130mm)
5.10”
(130mm)
13.0”
(330mm)
5.10”
(130mm)
6.5625”
(167mm)
1.20”
(31mm)
1.20”
(31mm)
1.20”
(31mm)
3.25”
(83mm)
3.25”
(83mm)
3.25”
(83mm)
3.25”
(83mm)
1.0”
(25mm)
1.0”
(
25mm
)
10.5”
(
267mm
)
1.0”
(
25mm
)
1.0”
(25mm)
0.75”
(19mm)
0.75”
(19mm)
0.9375”
(24mm)
0.9375”
(24mm)
11.0”
(279mm)
12.5”
(318mm)
MEMBER
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Altronix ALTV244175ULCB3 Installation guide

Altronix
Brand
Altronix
Model
ALTV244175ULCB3
Category
Electrical enclosures
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents