Intellinet 550857 User manual

NSC18-WN

PaN/TilT

NeTWork

Camera

uSer

maNual

MODEL

550857

INT-550857-UM-0709-01

2

CONTENTS

Table of CoNTeNTS

1 COMPONENTS & CONNECTIONS .................................................................6

2 SOFTWARE INSTALLATION ........................................................................... 8

2.1 Locating the IP Address of the Camera ...................................................8

2.2 Using the Admin Utility to Locate the Camera .........................................11

3 WEB MANAGEMENT INTERFACE ............................................................... 16

3.1 Logging On ............................................................................................ 16

3.2 Camera Settings .....................................................................................17

3.3 Pan & Tilt Settings ..................................................................................20

3.3.1 Preset Points ...............................................................................20

3.3.2 Guard Tour .................................................................................. 21

3.4 Network Settings ....................................................................................23

3.4.1 LAN .............................................................................................23

3.4.2 WLAN .........................................................................................24

3.4.3 Dynamic DNS .............................................................................. 26

3.4.4 UPnP ...........................................................................................27

3.4.5 LoginFree ....................................................................................28

3.5 Motion Detection Settings ......................................................................29

3.5.1 Motion Detection .........................................................................29

3.5.2 Motion Region .............................................................................30

3.5.3 E-Mail .......................................................................................... 32

  3.5.4 FTPConguration .......................................................................33

  3.5.5 SDCardConguration ................................................................33

3.6 System Info ............................................................................................34

3.6.1 Camera Information ....................................................................34

3.6.2 Date/Time Settings ......................................................................34

3.6.3 Utilities .........................................................................................35

3.6.4 Status ..........................................................................................36

3.7 Account ..................................................................................................36

3.8 SDHC ....................................................................................................38

3.8.1 Status ..........................................................................................38

3.8.2 Space Alarm ...............................................................................38

3.8.3 File Management.........................................................................39

4 SURVEILLANCE SOFTWARE ......................................................................39

4.1 Installing the Surveillance Software .......................................................39

4.2 Viewer Controls ...................................................................................... 42

 4.3 Conguration ..........................................................................................45

  4.3.1 CongureCameras .....................................................................45

4.3.2 General Options ..........................................................................50

4.4 Changing the Display Layout .................................................................54

5 TROUBLESHOOTING ...................................................................................57

6 SPECIFICATIONS ..........................................................................................59

section page

3

INTRODUCTION

iNTroduCTioN

Thank you for purchasing the INTELLINET NETWORK SOLUTIONS

™

NSC18-WN Pan/Tilt Network Camera, Model 550857.

Ideal for home-network-based video streaming, this camera is simple to

setupandoperate,soyoucansoonbeenjoyingthebenetsofthese

popular features:

• 1.3MegapixelCMOSimagesensorforcrystal-clearimages

• Motorizedwide-rangepan/tiltcontrolviaWebbrowserandutility

• Supportsimageresolutionsupto1280x1024;plussimultaneous

MPEG4 and Motion-JPEG image compression

• IntegratedSD/SDHCcardslotforon-boardstorageofupto8GB

• SupportsRTSP(Real-TimeStreamingProtocol);WPS(Wi-FiProtected

 Setup);WEPandWPA/WPA2(TKIPandAES)dataencryption;and

 UPnP(UniversalPlugandPlay)

• 4Xdigitalzoom

• Programmablepresetpositionsandpatrolmode

• 2T2RMIMOtechnologyforenhancedthroughputandcoverage

• Integratede-mail,FTP,DDNSandDHCPclient

• Audiosupport,withintegratedmicrophoneandexternalspeaker

output connector

• Integratedmulti-windowmotiondetection

• Easy-to-use16-channelcameraviewingandrecordingutility

•Three-YearWarranty

NOTE:Somescreenimagesaremodiedtottheformatofthismanual.

PACKAGE CONTENTS

• NSC18-WNPan/TiltNetworkCamera

• 2detachableantennas

• Poweradapter

• Quickinstallationguide

• SoftwareCDwithusermanual

• EthernetCat5RJ45cable:1.0m(3ft.)

NOTE: Video and audio surveillance may be forbidden by laws that vary

from country to country. Check the laws where you install this device

before using it for surveillance purposes.

4

REGULATORY STATEMENTS

regulaTory STaTemeNTS

EU DECLARATION OF CONFORMITY

This device complies with the essential requirements of the R&TTE

Directive1999/5/EC.Thisdeviceisa2.4GHzwidebandtransmission

system(transceiver)intendedforuseinallEUmemberstatesandEFTA

countries,exceptinFranceandItaly,whererestrictiveuseapplies.

In Italy, the end-user should apply for a license at the national spectrum

authoritiesinordertoobtainauthorizationtousethedeviceforsetting

up outdoor radio links and/or for supplying public access to

telecommunications and/or network services.

This device may not be used for setting up outdoor radio links in France,

and in some areas the RF output power may be limited to 10 mW EIRP

inthefrequencyrangeof2454–2483.5MHz.Fordetailedinformation,

the end-user should contact the national spectrum authority in France.

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE

STATEMENT

This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one of the following measures:

• Reorientorrelocatethereceivingantenna.

• Increasetheseparationbetweentheequipmentandreceiver.

• Connecttheequipmentintoanoutletonacircuitdifferentfromthat

to which the receiver is connected.

• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

This device complies with Part 15 of the FCC Rules. Operation is

subjecttothefollowingtwoconditions:1)Thisdevicemaynotcause

harmfulinterference,and2)Thisdevicemustacceptanyinterference

received, including interference that may cause undesired operation.

5

SAFETY PRECAUTIONS

FCC CAUTION

Anychangesormodicationsnotexpresslyapprovedbytheparty

responsible for compliance could void the user’s authority to operate

this equipment.

IEEE802.11bor802.11goperationofthisproductintheU.S.isrmware-

limited to channels 1 through 11.

FCC RADIATION EXPOSURE STATEMENT

ThisequipmentcomplieswithFCCradiationexposurelimitssetforth

for an uncontrolled environment. This equipment should be installed

andoperatedwithaminimumdistanceof20cm(approximately8in.)

between the radiator and your body. This transmitter must not be co-

located or operated in conjunction with any other antenna or transmitter.

SafeTy PreCauTioNS

This product has been designed with safety in mind, but as electrical

productscancausereswhichmayleadtoseriousdamageandinjury

if not used properly, observe these precautions:

• Don’topenthecamerahousingorotherwiseexposeyourselfto

 dangerousvoltageorotherhazardsinside.

• Don’tattach/connectaccessoriesthataren’tdesignedforthisdevice.

• Avoidoperatingorstoringthecamerainextremetemperatures(see

 Specicationsintheusermanual).

• Avoidexposingthecameratodirectsunlightforalongtime.

• Don’tplacethecameranearheatsources.

• Don’tplacethecameranearwater(e.g.,nexttoabathtuborsink)or

 inanextremelyhotorhumidenvironment.

• Don’tplacethecameranearsourcesofstrongmagnetism.

• Don’tplacethecameranearsourcesofpowerfulelectromagnetic

radiation, such as radios or TV transmitters.

• Don’tplacethecamerainlocationssubjecttostrongvibrationor

shock.

6

COMPONENTS & CONNECTIONS

Focus

adjustment

ring

LEDs

Built-in

microphone

Wireless

antenna

(1of2)

1 ComPoNeNTS & CoNNeCTioNS

1.1 Front and Side

Wireless Antennas —

Connect the camera to

the wireless network.

Focus Adjustment Ring —

For manually setting

the best image quality.

Built-in Microphone —

For two-way audio.

Power LED — Lights after

the camera completes

the booting process.

Audio LED — Lights when

 Audioisenabled;

 ashesifactive.

LAN LED — Lights

when the LAN

 portisinuse;

 ashesduring

data transfers.

WLAN LED — Lights when the wireless LAN

 portisinuse;ashesduringdatatransfers;

 ashesoncepersecondwhenwaitingfor

a WPS connection from an access point.

Reset — For reverting to the factory default

settings. Use a straight pin, paper clip or

other pointed object to press and hold this

 recessedbuttonin(onthecamerabase’s

 rightside,asshownatright)for5seconds.

Tripod Ring — For securing the camera to a

tripod or wall/ceiling mount. This twist ring

is on the underside of the camera base.

Reset

7

COMPONENTS & CONNECTIONS

1.2 Back / Connections

1. Connect one end of the included

 Ethernetcable(orasimilarone)

to your local area network and

the other end to the LAN port.

NOTE: You can skip this step

if you plan to use a wireless

LAN only.

2. Plug the included power

adapter into an A/C outlet

and connect it to the 12VDC

power jack.

3. Attach the two included

antennas to the connectors

 (shownalreadyattached

 atright).

4. Press the WPS buttons

on both the camera and

 youraccesspoint(s)to

establish Wi-Fi Protected

Security between the devices.

5.Ifdesired,connectanexternalspeakertothe3.5mmAudioOutjack.

6.Asneededordesired,insertanSD(securedigital)orSDHC(high-

 capacity)cardintotheSDslottodownloadupto8GBofvideoles.

NOTE:RefertoSection3.5.5MotionDetection/SDCardConguration

and Section 3.8 SDHC.

7. Positionthecamerainasecurelocation(seeSafetyPrecautions

 above)andaimitasdesired.

8

SOFTWARE INSTALLATION

2 SofTWare iNSTallaTioN

Oncethecameraconnectionshavebeenmade,launchInternetExplorer

on your computer and proceed with the instructions in the following sections.

2.1 Locating the IP Address of the Camera

The default IP address of this camera is 192.168.2.3. If you prefer to

assign a different IP address to it, log on to the Web management

interfaceofthecamerarst.

IftherstthreesectionsoftheIPaddressofyourcomputeraren’t

192.168.2, you’ll need to change the IP address of your computer.

1. From your desktop, go to Start, then Control Panel.

9

SOFTWARE INSTALLATION

2. Double-click the Network Connections icon.

3. Right-click on

the Local Area

Connection

icon, then click

“Properties”

from the menu

that displays.

10

SOFTWARE INSTALLATION

4. With the General

menu tab/screen

displayed, select

“Internet Protocol

 (TCP/IP),”then

click “Properties.”

5.Inthe“IPaddress”eldonthesubsequentPropertiesscreen,enter

an IP address beginning with “192.168.2” and ending with a value

between 2 and

 254(asshown).

In the “Subnet

 mask”eld,enter

“255.255.255.0.”

Click “OK.”

NOTE: If you forget

the IP address of the

camera after you

change it, there are

two ways to recover it:

• Resetbackto

 192.168.2.3(and

 loseallsettings);

• Askyournetwork

administrator to

check the DHCP

 releasetable(if

the camera was

set to obtain the

IP address by

 DHCP).

11

SOFTWARE INSTALLATION

2.2 Using the Admin Utility to Locate the Camera

If you can’t connect to the camera using the above procedure, you can

use the admin utility software to search for cameras connected to your

local area network.

Insert the included software CD, and it will automatically begin to install

the admin utility. NOTE: If it doesn’t auto-start, go to Start on your

desktop,thenMyComputer;double-clickontheCDdrivewherethe

software CD is located, and double-click the “Setup_Admin_3.0.1” icon,

as shown below.

1. WhentheWelcometotheIPCamAdminUtilitySetupWizardscreen

 displays,click“Next.”

12

SOFTWARE INSTALLATION

2.WhentheSelectDestinationLocationscreendisplays,click“Next”to

use the default installation folder and continue, or click “Browse” to

 selectanexistingfolderordrivetoinstalltheadminutility.

3. When the Select Additional Tasks screen displays, you may select the

 “Createadesktopicon”and“CreateaQuickLaunchicon”options,

 thenclick“Next”tocontinue.

13

SOFTWARE INSTALLATION

4.WhentheReadytoInstallscreendisplays(presentingalltheselected

 options),click“Install”tocontinueor“Back”tomakemorechanges.

5.WhentheCompletingtheIPCamAdminUtilitySetupWizardscreen

displays, click “Finish” to complete the install. NOTE: The “Launch

IPCam Admin Utility” option should be selected by default.

14

SOFTWARE INSTALLATION

After the camera’s admin utility is launched, all cameras found on your

local area network will be displayed with basic information. To connect

to a certain camera using your Web browser, double-click the camera

listed.

ThisinitialscreenalsointroducestheLanguagedrop-downmenu(above

thecamera-listeld)andthethreeiconsatthebottom(fromlefttoright):

SearchCamera;BrowseCameraviaWeb;andCongureCamera.

Search Camera—Clicktosearch(andrefreshthesearch)forall

cameras on the local area network.

Browse Camera via Web — Select a camera on the list, then click to

connect to the camera using your Web browser.

Congure Camera—Clicktocongureacamera’snetworkandsecurity

settings. When the Login screen

 displays,llinthe“Password”eld

 (thedefaultpasswordis“1234”)

and click “OK” to display the LAN

 SettingandSecurityscreens(both

 shownbelow).NOTE: The default

username, “admin,” cannot be

changed here.

15

SOFTWARE INSTALLATION

DHCP — Select to set the camera to automatically obtain an IP address

from the DHCP server on the local area network.

Manual IP — Select to input the IP address information manually.

Click “OK” to save the settings.

16

WEB MANAGEMENT INTERFACE

OntheSecurityscreen(above),youcanchangethecamera’sname

andpassword(asontheLoginscreen,theusernameisalways“admin”

andcan’tbechanged).Besureyouenterthesamepasswordinboth

the“NewPassword”and“ConrmPassword”elds;otherwise,you’ll

be prompted to enter the new password again. Click “OK” to save the

settings;click“Cancel”todiscardchanges.

3 Web maNagemeNT iNTerfaCe

3.1 Logging On

With new camera purchases, there should be no problem with the login/

logon procedures. Remember, however, that if you have obtained this

camera from another party after initial installation, then you’ll probably

need to reset the password.

1. With the camera powered on, launch your Web browser and enter

the IP address of the camera in the address bar.

2. When the Internet Camera login

 screendisplays(right),entera

username and password and

click “OK.” As before, the “User

Name” and “Password” defaults

are “admin” and “1234.” NOTE:

If this login screen doesn’t

display, go back and re-enter

the IP address as necessary.

Once you’ve logged in properly,

your browser should display the

 “ThissitemightrequirethefollowingActiveXcontrol...”message,as

shown below.

17

WEB MANAGEMENT INTERFACE

3. The NSC18-WN Pan/Tilt Network Camera

 requiresaspecialActiveXcontrol(plug-in)

in order to work properly. Right-click on the

message in the address bar to display an

 optionsmenu(right),thenclick“InstallActiveXControl...”tocontinue.

4.WhentheSecurityWarningscreendisplays(below),click“Install.”

You should now be able to view live images on the Camera screen

(see3.2CameraSettingsbelow).

NOTE: If one or both of the messages

shown here display, your computer may

not have the display capability that this

camerarequires(refertoSection6

Specications)oryoumaynothave

MicrosoftDirectXinstalled(whichyoucandownload

fromMicrosoft’sWebsite:www.microsoft.com).In

some cases, your computer displays the image from

the camera correctly but you still see these messages.

If this happens, you can just ignore them.

3.2 Camera Settings

Asmentioned,therstscreenthatdisplaysafteryoulogontotheWeb

managementinterfaceistheCamerascreen(below).Thisistheonly

oneofthesevenoptionsonthehorizontalmenubar(justabovethe

imagearea)thatpresentsthelivecameraimage.Youcan,ofcourse,

click on the Camera option from anywhere within the interface to return

to the live-image display.

18

WEB MANAGEMENT INTERFACE

Pan/Tilt Speed—Thisspeciesthemovingspeedwhenyouusethe

Pan/Tilt function to point the camera in a different direction. Options

 are“1”(fastest)to“5”(slowest).Thefasterthespeed,thelessprecise

the control of the movement.

Resolution—Optionsforthevideoresolutionare“1024x768,”“640x

 480”and“320x240”@MPEG4;or“1280x1024,”“640x480”and

 “320x240”@ MJPG. Higher resolution provides more details in the

camera image but consumes more bandwidth, which will make the

image refresh very slowly. If you have a slow Internet connection, you

may want to use a lower resolution to make the image refresh faster.

NOTE:“320x240”mayreducetheimagetoomuchonahigh-res

monitor. To save bandwidth and maintain high resolution, select a

 lowerVideoQualitysetting(seebelow).

Video Quality—Theveoptionsforsettingthequalityofthecaptured

image range from “Lowest” to “Highest.” As with resolution, a higher

image quality will provide more detail, but cost additional bandwidth.

If you just want to see if there’s anything moving within the camera’s

19

WEB MANAGEMENT INTERFACE

 eldofview,selectalowerimagequalitytogetahigherimagerefresh

rate.

Video Type — Select the video encoding type: “MJPEG” or “MPEG4.”

Frame Rate—Thehighestimagerefreshrateofthiscamerais30(the

 sameasaTV).However,ifyouareusinganInternetconnectionwith

limited bandwidth and you don’t need a fast image refresh rate, you

 canlimitthemaximumrefreshrate(framerate).Optionsare“30,”

“15,” “10,” “5” and “3.”

Frequency—Iftheareathecameraisviewingfeaturesuorescent

 lighting,theimagemaylooklikeit’sickering.Inthiscase,youcan

adjust this setting to the frequency of the electrical power to improve

the image quality. If you don’t know which setting to use, just try each

 oneandselecttheonewiththeleasticker.

Flip Mode — If you’re mounting the camera on a ceiling or wall rather

 thananyotherhorizontalsurface,youcanusethisfunctiontorotate

the displayed image.

Show Date/Time — Select “Enable” to display the current date and time

 oftheinternalclockofthecameraattheupper-leftcorneroftheimage;

select “Disable” to hide date/time.

Video Quality Control — To account for different viewing conditions, you

can adjust the video quality by controlling the brightness, saturation

and sharpness levels of the displayed image. Select one of the Video

 Qualityoptionsfromthedrop-downmenu,thenclick“+”or“–”to

increase/decrease the level.

Volume—Click“+”or“–”to increase/decrease the volume level.

Apply — Click to put any of the above changes into effect. NOTE: Any

changes made with the following functions are immediate.

Pan/Tilt Control — This lets you aim the camera in different

directions. Click any of the eight directional buttons to

 movethecamera;click“H”tomovethecamerabackto

 the“home”(original)position.

Preset Points — You can set up to nine preset camera viewing positions,

then just click the corresponding number to

instantly move the camera to that preset point.

 (See3.3.1Pan&Tilt/PresetPointsfordetails.)

Click “C” to automatically move the view through all preset points.

Snapshot—Clicktosavethedisplayedimageasanimagele.A

 messageboxwillappear,showingthelenameandlocationofthe

20

WEB MANAGEMENT INTERFACE

 savedimagele(thedefaultlenameisthecurrentdateandtime).

 Thedefaultdirectoryusedtosaveimageleis“C:\”;butyoucan

 changebyclickingthetexteldtotherightof“Snapshot”andentering

a new directory.

Recording—ClicktorecordthedisplayingimageasavideoleinAVI

 format.YoucanplaybackthevideoleusingWindowsMediaPlayer.

 Tostoprecording,click“StopRecording”(thesamebutton).Aswith

 “Snapshot,”youcanchangethedirectoryusedtosavethele.

Full Screen—Clicktodisplaytheimageinfull-screenmode(usesall

 availablespacetodisplaythecapturedimage).

Digital Zoom — Click to

enlarge any portion

of a captured image.

Select “Enable,” then

drag the slide bar left

or right to adjust the

 zoomratio.Youcan

also use your mouse

 todragthezoomarea

 (theyellowsquare)torepositionitasdesired.

Fit to Window—Clicktoadjusttheimagesizetotthebrowserwindow.

Speaker to IP Cam — You can transmit the voice received by your

 computer’smicrophonetothecamera’sexternalspeaker.Clickand

hold this button, then speak into the microphone. NOTE:Theexternal

speaker must be connected to the camera.

3.3 Pan & Tilt Settings

In addition to pan and tilt functions, this menu option presents a couple

ofhandyfeaturesthatallowyoutocongurethecameraforautomatic

movements.Clickeither“PresetPoints”or“GuardTour”tocongure.

3.3.1 Preset Points

Thecamerahasninememoryslotssoyoucandeneparticularcamera

positions as “preset points” and save them for later recall.

1. Select a memory slot from the “Available Positions” drop-down menu.

2.Clickontheimage(atthetoptomoveup,onthelefttomoveleft,etc.)

to aim the camera in that direction. You may want to set Pan/Tilt Speed

to a slower setting in order to move the camera more precisely.

Page is loading ...

Intellinet 550857 User manual

This manual is also suitable for

Intellinet 550857 User manual

Related papers

Other documents