Crafstman CMXEVBE17585 User manual

Category
Vacuum cleaners
Type
User manual

This manual is also suitable for

Part No. SP7088 Printed in Mexico
INSTRUCTION MANUAL | GUIDE D’UTILISATION | MANUAL DE INSTRUCCIONES
IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US.
POUR TOUTE QUESTION OU TOUT COMMENTAIRE, NOUS CONTACTER.
SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS.
5 GALLON (18 LITERS) ASH VACUUM
ASPIRATEUR POUR RAMASSER DES CENDRES
DE 18 LITRES (5 GALLONS)
ASPIRADORA DE CENIZA DE 18 LITROS (5 GALONES)
CMXEVBE175850
1-888-331-4569 WWW.CRAFTSMAN.COM
SP7088-2 CMXEVBE175850.indb 1 10/24/19 11:59 AM
!
DANGER: Indicates a hazardous situation which, if not avoided, will result in death or serious
injury.
WARNING: Indicates a hazardous situation which, if not avoided, could result in death or serious
injury.
CAUTION: Indicates a hazardous situation which, if not avoided, may result in minor or moderate
injury.
(Used without word) Indicates a safety related message.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.
!
!
2
Definitions: Safety Alert Symbols and Words
This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk
of personal injury or property damage.
Components
Fig. A
1 Carry Handle
2 Cord Wrap Area
3 Hose Wrap Area
4 ON/OFF Switch
5 Powerhead Assembly
6 Vacuum Inlet Port
7 Drum
8 Drum Latches (2)
9 Power Cord
10 Accessory Storage Slots (2)
If you have any questions or comments about this or
any product, call CRAFTSMAN toll free at:
1-888-331-4569.
WARNING: Read all safety
warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
WARNING: Never modify the
product or any part of it. Damage or personal injury
could result.
WARNING: To reduce the risk of
injury, read the instruction manual.
!
!
!
9
10
1
3
2
4
5
6
7
8
!
SP7088-2 CMXEVBE175850.indb 2 10/24/19 11:59 AM
3
IMPORTANT SAFETY INSTRUCTIONS
Read and understand this manual and all labels on the
Vacuum before operating.
Use only as described in this manual.
Do not pick up anything that is burning or smoking, like
cigarettes, matches or hot, glowing, or burning embers.
Pick up cold ash only. Be aware that ash/embers can be hot
for days after use.
Use caution when vacuuming materials that appear to have
cooled, but may actually be hot inside. First check for hot
spots by raking through the ashes/coals. Air flow created
during vacuuming may cause hot ash to re-ignite. As you
vacuum, constantly check the nozzle, hose, drum, and motor
for excessive temperatures. If you notice an increase in
temperature, turn off the vacuum immediately. Unplug the
vacuum and remove the vacuumed material from the drum.
The drum must be emptied and cleaned after each use,
and before picking up other household debris.
Allow the vacuum to cool before storage, especially enclosed
storage.
Do not use paper dust bags.
To reduce the risk of damage from accidental hot ember
pickup, do not place the vacuum on surfaces susceptible
to heat damage, such as carpeting, vinyl flooring, or wood
surfaces.
Do not leave vacuum running while unattended - you
may fail to notice important signs indicating abnormal
operation such as loss of suction, or abnormal motor noises.
Immediately stop using vacuum if you notice these signs.
Do not leave vacuum when plugged in. Unplug from
outlet when not in use and before servicing.
Sparks inside the motor can ignite flammable vapors
or dust. To reduce the risk of fire or explosion, do not
use near combustible liquids, gases, or dusts, such as
gasoline or other fuels, lighter fluid, cleaners, oil-based
paints, natural gas, coal dust, magnesium dust, grain
dust, aluminum dust, or gun powder.
To reduce the risk of inhaling toxic vapors, do not
vacuum or use near toxic or hazardous materials.
To reduce the risk of electric shock, do not expose
to rain or allow liquid to enter motor compartment.
Store indoors.
This Ash Vacuum is not intended for use by
persons (including children) with reduced physical,
sensory, or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
Only use extension cords that are intended
for outdoor use. Use only three-wire outdoor
extension cords that have three-prong grounding plugs
and grounding receptacles that accept the vacuum’s
plug. Extension cords in poor condition or too small in
wire size can pose fire and shock hazards. To reduce
the risk of these hazards, be sure the cord is in good
condition and that liquid does not contact the
connection. Do not use an extension cord with
conductors smaller than 1,3 mm
2
(16 AWG) in size.
Do not use with damaged cord, plug, or other parts.
If your Vacuum is not working as it should, has
missing parts, has been dropped, damaged, left
outdoors, or dropped into water, call customer service at
1-888-331-4569 (Mexico 001-881-331-4569).
Connect only to a properly-grounded outlet.
See grounding instructions
Do not put any object into ventilation openings. Do not
vacuum with any ventilation openings blocked; keep
free of dust, lint, hair or anything that may reduce air
flow.
Keep hair, loose clothing, fingers, and all parts of body
away from openings and moving parts.
To reduce the risk of falls, use extra care when cleaning
on stairs.
To reduce the risk of personal injury or damage to
Vacuum, use only CRAFTSMAN recommended
accessories.
To reduce the risk of eye injury, wear safety eyewear.
The operation of any utility vacuum can result in foreign
objects being blown into the eyes, which can result in
severe eye damage.
Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
Turn off Vac before unplugging.
To reduce the risk of injury from accidental starting,
unplug power cord before changing or cleaning filter.
Do not unplug by pulling on cord. To unplug, grasp the
plug, not the cord.
Do not pull or carry by cord, use cord as handle, close a
door on cord, or pull cord around sharp edges or corners.
Keep cord away from heated surfaces.
WARNING:
To reduce the risk of fire, electric shock, or injury:
!
When using this Vacuum, always follow basic safety
precautions including the following:
This vacuum is intended to pick up COLD ash from
fireplaces, grills, ovens, ashtrays, etc. Read and understand
this manual and all labels on this Ash Vacuum before
operating.
SP7088-2 CMXEVBE175850.indb 3 10/24/19 11:59 AM
4
CAUTION:
To reduce the risk of hearing damage, wear ear
protectors when using for an extended time or
in a noisy area.
For dusty operations, wear dust mask.
Static shocks are common when the relative
humidity of the air is low. Vacuuming fine
debris with your Vac can deposit static charge on
the hose or Vacuum. To reduce the frequency of
static shocks in your home or when using
this Vacuum, add moisture to the air with a
humidifier.
SAVE THESE INSTRUCTIONS
WARNING:
For your own safety, read and understand Instruction
Manual.
Do not run unattended.
• Do not pick up hot ashes, coals, flammable,
combustible / self-igniting, toxic, or other hazardous
materials.
Do not use around explosive liquids or vapors.
To reduce the risk of electric shock, do not use on wet
surfaces.
Do not expose to rain. Store indoors.
This is a dry vacuum only; NEVER vacuum liquids
with this product.
Observe the following warnings that appear on the
Lighted Nozzle.
WARNING:
Keep batteries out of reach of small children. Consult
a physician immediately if a battery is swallowed;
severe burning or injury may occur.
• Battery contains Perchlorate Material - Special
handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
!
!
Observe the following warnings that appear on the Vacuum.
WARNING:
Risk of fire and Heat Damage.
This vacuum is intended to pick up COLD ash from
fireplaces, grills, ovens, ash-trays, etc. Do not pick up
hot, glowing, or burning ash/embers. Pick up cold ash
only. Be aware that ash/embers can be hot for days after
use. To reduce the risk of damage from accidental hot
ember pickup, do not place the vacuum on surfaces
susceptible to heat damage such as carpeting, vinyl
flooring, or wood surfaces. Empty drum after each use.
Allow to cool before storing, especially in enclosed
spaces. Do not use dust collection bags.
!
!
FREE WARNING LABEL REPLACEMENT: If your warning
labels become illegible or are missing, call 1-888-331-4569
for a free replacement.
SP7088-2 CMXEVBE175850.indb 4 10/24/19 11:59 AM
5
This Ash Vacuum is intended for household use. It may be
used for vacuuming of dry debris, including cold ash from
fireplaces, grills, ovens, ash-trays, etc. It should not be used
to pick up liquids.
Read this Instruction Manual to familiarize yourself with
the product features and to understand the specific usage
of your new vacuum.
INTRODUCTION
Section Page
Section Page
Important Safety Instructions.......................2-4
Introduction .......................................5
Grounding Instructions..............................6
Carton Contents ....................................7
Installation .....................................8-11
Powerhead Assembly .............................8
Powerhead Disassembly...........................8
Insert Locking Hose ...............................9
Hose Assembly...................................9
LED Lighted Nozzle Usage ........................10
LED Lighted Nozzle Battery Replacement............10
Power Cord Storage..............................11
Accessory Storage ...............................11
Hose Assembly Storage...........................11
Operation .....................................12-13
Motor / Electrical ................................12
Emptying the Drum..............................13
Maintenance...................................14-15
HEPA Media Filter ...............................14
Filter Removal and Replacement...................14
Filter Removal ..................................14
Filter Installation ................................14
Cleaning a Dry Cartridge Filter.....................15
Cleaning and Disinfecting the Ash Vacuum..........15
Cord Maintenance & Storage ......................15
Ash Vacuum Storage .............................15
Service / Repair Parts...............................16
Warranty .........................................17
TABLE OF CONTENTS
SP7088-2 CMXEVBE175850.indb 5 10/24/19 11:59 AM
6
This Vacuum must be Grounded. If it should
malfunction or break down, Grounding provides a path
of least resistance for Electric Current to reduce the risk of
Electric Shock. This Vacuum is equipped with a Cord
having an Equipment-grounding Conductor and
Grounding Plug. The Plug must be inserted into an
appropriate Outlet that is properly installed and Grounded
in accordance with all Local Codes and Ordinances.
Properly
Grounded
Outlet
Grounding
Prong
3-Prong
Plug
GROUNDING INSTRUCTIONS
Fig. B
This Vacuum is for use on a nominal 120 Volt Circuit, and
has a Grounded Plug that looks like the Plug shown.
A Temporary Adapter that looks like the Adapter shown
may be used to connect this Plug to a 2-Pole Receptacle,
as shown. If a properly Grounded Outlet is not
available, the Temporary Adapter should be used only
until a properly Grounded Outlet can be installed by a
Qualified Electrician.
The Green Colored Rigid Ear, Lug or the like extending
from the Adapter must be connected to a Permanent
Ground such as a properly Grounded Outlet Box Cover.
Whenever the Adapter is used, it must be held in place
by a Metal Screw.
NOTE: In Canada, the Use of a Temporary Adapter is Not
Permitted by the Canadian Electrical Code.
Make sure this is a
metal screw connected
to a known ground
Green
Grounding Lug
Metal
Screw
3-Prong Plug
Adapter
2-Prong Outlet
Fig. C
WARNING:
Improper connection of the equipment grounding
conductor can result in a risk of electric shock. Check
with a qualified electrician or service person if you are
in doubt as to whether the outlet is properly grounded.
Do not modify the plug provided with the appliance -
if it will not fit the outlet, have a proper outlet installed
by a qualified electrician.
!
SP7088-2 CMXEVBE175850.indb 6 10/24/19 11:59 AM
Key Description Qty.
A Ash Vacuum (5 Gallon/18 Liters) 1
B Metal Cover 1
C HEPA Media Filter 1
D Filter Screen 1
E Extension Nozzle 1
F Wand Nozzle 1
G Locking Hose (metal lined)
with LED Lighted Nozzle 1
H Instruction Manual 1
Some items may come preassembled.
If they are not present in the carton, check the vacuum
powerhead to see if they are preassembled.
7
Remove entire contents of carton. Check each item against
the Carton Contents List.
If any parts are damaged or missing, return the product
to the retailer from which is was purchased for exchange.
CARTON CONTENTS (Fig. D)
Fig. D
B
C
E
D
F
G
H
A
SP7088-2 CMXEVBE175850.indb 7 10/24/19 11:59 AM
8
Powerhead Assembly (Figs. E & F)
1. Line up front of Powerhead Assembly with Vacuum
Port located on the front of the Drum, as shown.
2. Place Powerhead Assembly on top of Drum.
3. Be sure Powerhead Assembly completely covers the
top of the Drum so leakage does not occur.
4. Rotate the Latches on each side of the Drum,
positioning the Latch Hooks over the Lip of the
Powerhead Assembly.
5. Snap down the bottom edge of the Latches to secure
the Powerhead Assembly to the Drum.
INSTALLATION
Fig. E
Powerhead Disassembly (Fig. G)
Fig. F
Vacuum
Port
Drum
Powerhead
Assembly
Lip
ROTATE
LATCH
UP
SNAP
DOWN
LATCH
Powerhead
Assembly
Latch
Fig. G
1. Grasp the Drum Latches on both the right and left side
of the Vacuum.
2. Slowly pull the bottom of the Latches up and away
from the Drum.
3. The top of the Latches will then be free of the
Powerhead Assembly.
4. Lift the Powerhead Assembly from the Drum and place
it on a dry surface.
WARNING:
For your own safety, never connect plug to
power source outlet until all assembly steps
are complete and you have read and under-
stood the safety and operation instructions.
Do not operate vacuum with any parts damaged or
missing.
!
SNAP
DOWN
LATCH
Latches
ROTATE
LATCH
UP
Powerhead Assembly
Lip
SP7088-2 CMXEVBE175850.indb 8 10/24/19 11:59 AM
9
Insert Locking Hose (Fig. H)
NOTE: Use ONLY the Metal Lined Hose and Metal
Accessories provided with this Ash Vacuum.
1. Align Hose Tabs with Vacuum Inlet and insert the
Locking End of the Hose into the Vacuum Inlet of the
Vacuum Drum, as shown.
2. Rotate the Hose clockwise to lock into place.
3. To remove the Hose from the Vacuum, rotate the
Locking Hose Counterclockwise and pull the Hose out
of the Vacuum Inlet.
Fig. H
Inlet
Locking Hose
(Metal Lined)
with LED Light
ROTATE HOSE
CLOCKWISE
TO LOCK
Hose Locking End
Hose Assembly (Figs. I & J)
1. Slide the Round End of the Extension Nozzle into the
smaller Tapered End of the Wand Nozzle.
Fig. I
Wand
Nozzle
Extension
Nozzle
2. Loosen the Two LED Assembly Screws, located at the
bottom of the LED Lighted Nozzle.
3 Slide the Wand Nozzle through the LED Assembly and
into the Rubber Hose Fitting.
4. Retighten the Two LED Assembly Screws to secure the
LED Assembly to the Hose Assembly.
Fig. J
LED Lighted
Nozzle
Screws (2)
Wand Nozzle
SP7088-2 CMXEVBE175850.indb 9 10/24/19 11:59 AM
10
LED Lighted Nozzle Usage (Fig. K)
1. Press Button to activate LED light while Vacuuming.
2. Slide the Switch Forward to Lock the LED Light in the
ON position.
3. Slide the Switch Back to the OFF position after use.
Fig. K
LED Lighted Nozzle Battery Replacement
(Fig. L)
1. To access Batteries, remove and retain the Battery
Access Panel Screw.
2. Remove and retain the Four Screws from the LED
Assembly, releasing the Switch Button Module.
3. The Two Batteries are located under the Switch
Button module. Dispose Batteries in the proper waste
disposal container.
4. The LED Light uses Two CR2016 Lithium Batteries that
are replaceable.
5. Reposition the Switch Button Module over the Battery
Compartment. Install the previously removed Four
Screws into the Switch Button Module to secure.
6. Reposition the Battery Access Panel over the Switch
Button Module. Install the previously removed Screw
into the Battery Access Panel to secure.
WARNING:
Keep batteries out of reach of small children. Consult
a physician immediately if a battery is swallowed.
Severe burning or injury may occur.
Battery contains Perchlorate Material - Special handling
may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
!
LED Button
LED
Assembly
Fig. L
Switch
Button
Module
CR2016
Lithium
Batteries
(2)
Battery
Access
Panel
Screw (1)
Screws (4)
LED
Assembly
SP7088-2 CMXEVBE175850.indb 10 10/24/19 11:59 AM
11
Hose Assembly Storage (Fig. O)
Wrap the Hose around the top of the cooled Powerhead
Assembly, positioning the Hose under the Carry Handle/
Hose Wrap Area.
CAUTION:
Do not operate vacuum while the hose or
accessories are stored on the wet/dry vacuum’s
powerhead assembly.
Fig. O
WARNING:
Do not put any object into ventilation openings.
Do not vacuum with any ventilation openings blocked;
keep free of dust, lint, hair or anything that may reduce
air flow.
!
Hose Wrap
Area
Hose
Accessory Storage (Fig. N)
The Accessories can be stored on the rear of the Powerhead
Assembly by placing each Accessory into the Powerhead
Assembly Slots.
Fig. N
Powerhead
Assembly
Slots (2)
Accessories
Power Cord Storage (Fig. M)
The Power Cord should be wrapped around the Powerhead
Assembly Carry Handle.
Snap the Cord Clip onto the Power Cord, to secure in place.
Fig. M
Power
Cord
Powerhead
Assembly
Cord
Storage
Cord Clip
WARNING:
To prevent serious injury from electrical shock,
stop vacuum use immediately if the power cord is
damaged. Take the vacuum to a qualified service dealer
for inspection and possible repair.
!
!
SP7088-2 CMXEVBE175850.indb 11 10/24/19 11:59 AM
12
WARNING:
To reduce the risk of fire, explosion,
or damage to Vacuum:
OPERATION
Do not leave Vacuum running while
unattended - you may fail to notice import-
ant signs indicating abnormal operation such
as loss of suction, debris exiting the exhaust,
or abnormal motor noises. Immediately stop
using Vacuum if you notice these signs.
Do not leave Vacuum plugged in when not in
use.
Sparks inside the motor can ignite airborne
flammables. Do not operate Vacuum near
flammable liquids or in areas with flammable gases,
vapors, or explosive / airborne dust. Flammable
liquids, gases, and vapors include: lighter fluid,
solvent-type cleaners, oil-based paints,
gasoline, alcohol, and aerosol sprays. Explosive
dusts include: coal, magnesium, aluminum, grain,
and gun powder.
Do not vacuum up explosive dusts, flammable
liquids, or hot ashes.
The drum must be emptied and cleaned after
each use, and before picking up other household
debris.
Motor / Electrical (Fig. P)
This Ash Vacuum is rated for use with 120 Volt 60 Hz
supply. The Vacuum is equipped with a Thermal Protection
Cutoff Switch which will remove Power from the Vacuum
Motor if excessively high Operating Temperatures are
detected. This condition may arise as the result of a
blocked Vacuum passage, or clogged Filter. If a Thermal
trip takes place, immediately Toggle the Vacuum’s
Switch to OFF, Unplug the Unit and inspect for an airflow
blockage in the Hose and verify the condition of the Filters
(see Maintenance). Clean or replace the Filters as required.
The Vacuum will require several minutes to cool down to
a safe operating temperature. When this temperature is
attained, the Thermal Switch will automatically Reset and
the Vacuum will be able to be used in the normal manner.
After you Plug the Power Cord into the Outlet, turn the Unit
on by pushing the Switch from position “O” to position “l”.
The symbols used on the Switch Actuator are International
“On & Off” Symbols:
!
=
OFF
=
ON
Fig. P
"OFF"
"ON"
WARNING:
To reduce the risk of electric shock or injury:
Do not expose to rain or allow liquid to enter
motor compartment. Store indoors.
Do not handle plug, switch, or Vacuum with wet
hands.
Unplug Vacuum before servicing. If your Vacuum
is not working as it should, has missing parts,
has been dropped, damaged, left outdoors, or
dropped into water, call customer service at
1-888-331-4569 (Mexico 001-881-331-4569).
When using an extension cord, use only
outdoor-rated cords that are in good condition.
Do not allow the connection to come into contact
with liquid.
!
CAUTION:
To reduce the risk of hearing damage, wear ear
protectors when using the Vacuum for an extended
time or in a noisy area.
!
SP7088-2 CMXEVBE175850.indb 12 10/24/19 11:59 AM
13
NOTE: Do not store the Vacuum immediately after Ash
removal or other use in a confined area or enclosed space.
Allow the Powerhead Assembly to cool and remove Ash
from Drum before storage.
1. Grasp the Drum Latches on both sides of the
Powerhead Assembly.
2. Slowly Pull Up on the Drum Latches, away from the
Drum.
3. The top of the Latches will be free of the Powerhead
Assembly.
Emptying the Vacuum Drum (Figs. Q & R)
WARNING:
To reduce the risk of injury from accidental starting,
unplug power cord before emptying the vacuum
drum.
!
Fig. Q
Drum
PULL
LATCH
UP AND
AWAY
ROTATE
LATCH
DOWN
ROTA
TE
LATCH
DOWN
PULL
LATCH
UP AND
AWAY
Latch
Latch
NOTE: Be sure the Ash is cool prior to dumping the
contents into the proper waste disposal container.
4. Lift up on the Powerhead Assembly and set it on a
clean dry area.
5. Empty the Drum into the proper waste disposal
container.
6. Inspect the Filter per the “Filter Removal and
Installation” Section of this Manual.
7. Reassemble the Powerhead Assembly to the Drum.
Drum
Cold Ash
Fig. R
CAUTION:
To reduce the risk of hearing damage, wear ear
protectors when using the Vacuum for an extended
time or in a noisy area.
!
SP7088-2 CMXEVBE175850.indb 13 10/24/19 11:59 AM
14
MAINTENANCE
WARNING:
To reduce the risk of injury from accidental starting,
unplug power cord before changing or cleaning filter.
HEPA Media Filter
Your HEPA Media Filter should be cleaned often to
maintain peak Vacuum performance.
IMPORTANT: It is very important that the screen filter is
installed prior to use.
NOTE: The HEPA Media Filter is made of high quality
material designed to stop dust and smaller particles.
Handle the HEPA Media Filter carefully when
removing to clean or installing a new HEPA Media
Filter. Creases in the HEPA Media Filter pleats may
occur from installation but creases will not affect the
performance of the HEPA Media Filter.
!
Filter Removal and Installation
Filter Removal (Fig. S):
1. Rotate the Filter Screen / HEPA Media Filter
Counter-Clockwise.
2. Remove the HEPA Media Filter from the Filter Screen.
NOTE: The Filter Screen should be cleaned with a brush.
3. Check the Motor Inlet Filter, clean or replace,
if necessary.
Fig. S
HEPA
Media Filter
Filter
Screen
Raised Lip
Filter Installation (Fig. T):
1. Replace Motor Inlet Filter.
2. Replace the HEPA Media Filter into the Filter Screen.
NOTE: Be sure to orient the HEPA Media Filter and the Filter
Screen in the correct position, as shown. The Filter Screen
has a raised lip on the inside of the Screen to hold it in place.
3. Rotate the Filter Screen/HEPA Media Filter Clockwise
onto the Powerhead Metal Cover.
Fig. T
Powerhead
Assembly
Filter
Screen
HEPA Media
Filter
Motor Inlet
Filter
Metal
Cover
SP7088-2 CMXEVBE175850.indb 14 10/24/19 11:59 AM
15
Cleaning A Dry Cartridge Filter
NOTE: For best cleaning results due to accumulated dust,
clean the Filter in an open area. Cleaning SHOULD be done
outdoors and not in the living quarters.
1. Light cleaning of some dry debris from the Filter can
be accomplished without removing the Filter from the
Vacuum. Simply slap your hand on top of the handle
while the Vacuum is turned off.
2. Remove Filter from Vacuum. Gently tap the Filter against
the inside wall of your Drum, or against the floor, and the
debris will loosen and fall.
Cleaning and Disinfecting the
Ash Vacuum
To keep your Vacuum looking its best, clean the outside with
a cloth dampened with warm water and mild soap.
To clean the Drum:
1. Dump debris out.
2. Wash the Drum thoroughly with warm water and mild
soap.
3. Wipe out with dry cloth.
Cord Maintenance & Storage
When vacuuming is complete, unplug the Power Cord and
wrap it around the Powerhead Handle. Accessories can be
stored on the rear of the Powerhead Assembly.
WARNING:
To assure product SAFETY and RELIABILITY, any other
maintenance, repairs and adjustments should be
performed by Authorized Service Centers, always
using CRAFTSMAN replacement parts.
!
Ash Vacuum Storage
Before storing your Vacuum, the Drum should be emptied
and cleaned. The Power Cord should be wrapped around the
Carry Handle. Positioning the Hose under the Carry Handle.
Accessories should be kept in the same area as the Vacuum
so they can be readily available. The Vacuum should be
stored indoors.
WARNING:
To prevent serious injury from electrical shock,
stop vacuum use immediately if the power cord is
damaged. Take the vacuum to a qualified service
dealer for inspection and possible repair.
!
SP7088-2 CMXEVBE175850.indb 15 10/24/19 11:59 AM
16
SERVICE / REPAIR PARTS
5 Gallon (18 Liter) Ash Vacuum
Model Number CMXEVBE175850
Electrical Ratings: 120 V~ 7.6 A 60 Hz
Always order by Part Number - Not by Key Number
WARNING: To reduce the risk of injury, unplug power cord before servicing the Wet/Dry Vacuum.
WARNING: All disassembly and repairs should be performed by qualified personnel.
!
!
Key
No. Part No. Description
1 836247-3 Handle, Carry
2 836248 Switch, Toggle
3 836265 Power Cord
4 836506 Drum Assembly
(Includes Drum, Drum Inlet,
Drum Latches, Carton & Label)
5 836257 Metal Cover
6 CMXZVBE38740 HEPA Media Filter
w/Motor Inlet Filter
Key
No. Part No. Description
7 836270 Metal Filter Screen
8 836276 Metal Extension Nozzle
9 836275 Metal Wand Nozzle
10 836277 Locking Hose
(Metal Lined)
11 836279 LED Lighted Nozzle Assembly
12 SP7088 Instruction Manual
1
5
7
6
4
8
9
11
10
12
2
3
SP7088-2 CMXEVBE175850.indb 16 10/24/19 11:59 AM
17
CRAFTSMAN
®
LIMITED WARRANTY – 3 YEARS
This limited warranty is provided by Emerson Tool Company, a division of Emerson Electric Co., (“We” or “Our” or “Us”) to
the original consumer owner (“Customer” or “You” or “Your”) of the CRAFTSMAN product with which this limited warranty
is provided (the “CRAFTSMAN Product”).
What is Covered
We warrant to You that your CRAFTSMAN Product will be free from defects in materials and workmanship when used
under normal conditions in accordance with the terms of the Instruction Manual provided to You with the CRAFTSMAN
Product, subject to the exclusions described below, for a period of three years commencing on the date of purchase by
You (the “Warranty Period”). This limited warranty terminates if the original purchaser transfers the CRAFTSMAN Product
to any other person or entity.
What is not Covered
This limited warranty does not extend to and expressly excludes:
Normal wear and tear and/or replacement attachments or accessories, including, without limitation, power cords,
hoses, filters, and other attachments or accessories that may be offered for sale by Us for use with the CRAFTSMAN
Product.
Damage or burnout of the CRAFTSMAN Product motor resulting from failure to clear a blockage occurring during the
normal course of use.
Loss or damage to the CRAFTSMAN Product resulting from conditions beyond Our control including without
limitation, misuse, accident, abuse, neglect, negligence (other than Our’s), overuse beyond intended capacity as set
forth in the Instruction Manual, or modifications or alterations made by anyone other than Us.
Loss or damage to the CRAFTSMAN Product resulting from failure to use the CRAFTSMAN Product in accordance with
the written instructions, guidelines, and terms and conditions set forth in the Instruction Manual.
TO THE EXTENT PERMITTED BY LAW, IN NO EVENT SHALL WE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR
CONSEQUENTIAL DAMAGES, INCLUDING ANY ECONOMIC LOSS, WHETHER RESULTING FROM NONPERFORMANCE,
USE, MISUSE OR INABILITY TO USE THE CRAFTSMAN PRODUCT OR FOR THE NEGLIGENCE OF ETC.
How to Obtain Service
US and Canada – To obtain warranty benefits contact us toll free at 1-888-331-4569 (Mexico 001-881-331-4569).
We will direct you to the nearest service center to review your vacuum for inspection, repairs or replacement.
Mexico - To obtain warranty benefits contact us toll free at 001-881-331-4569. We will direct you to the nearest service
center to review your vacuum for inspection, repairs or replacement.
No Other Express Warranty Applies
This limited warranty is the sole and exclusive warranty provided to You. No other express warranty, written or verbal,
applies including, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
No employee, agent, dealer, or other person is authorized to alter this limited warranty or make any other warranty on
behalf of Us.
What We will do to Correct Problems
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE LIMITED TO REPAIR, REPLACEMENT,
REFUND OF THE CRAFTSMAN PRODUCT.
After You have contacted CRAFTSMAN Product Customer Service Department, We will initiate warranty proceedings,
including a physical inspection, subject to the exclusions and the Warranty Period stated herein, to determine whether to
repair or replace the CRAFTSMAN Product or provide You with a refund.
The decision to repair or replace your CRAFTSMAN Product or to provide a refund is at Our sole discretion. Repair or
replacements provided to You by ETC are at no cost to You if covered under this limited warranty.
If we are unable to provide You with a suitable repaired or replacement CRAFTSMAN Product, we will provide you with
a refund equal to the purchase price of your CRAFTSMAN Product or a credit to be used toward the purchase of a new
CRAFTSMAN Product.
In the event of any dispute between CUSTOMER AND US, either party may choose to resolve the dispute by binding
arbitration. THIS MEANS IF EITHER CUSTOMER OR US CHOOSE BINDING ARBITRATION, NEITHER PARTY SHALL HAVE THE
RIGHT TO LITIGATE SUCH CLAIM IN COURT OR HAVE A JURY TRIAL. DISCOVERY AND APPEAL RIGHTS ARE LIMITED.
This limited warranty gives you specific legal rights, and you may also have other rights, which vary from State to State.
Some states do not allow the exclusion of incidental or consequential damages, so the above limitation may not apply.
SP7088-2 CMXEVBE175850.indb 17 10/24/19 11:59 AM
Part No. SP7088 Form No. SP7088-2 Printed in Mexico 10/2019
CRAFTSMAN®
is a registered trademark of Stanley Black & Decker, Inc., used under license.
es una marca registrada de Stanley Black & Decker, Inc., utilizada bajo licencia.
est une marque déposée de Stanley Black & Decker, Inc., utilisée sous licence.
2019 CRAFTSMAN
Product Manufactured by: EMERSON TOOL COMPANY
Producto fabricado por: 8100 W. Florissant • St. Louis, MO 63136
Produit fabriqué par : U.S. & Canada Only • É.-U. et Canada seulement • EE.UU. y Canadá solamente
c
SP7088-2 CMXEVBE175850.indb 18 10/24/19 11:59 AM
Pièce N° SP7088 Imprimé N° SP7088-2 Imprimé au Mexique 10/2019
CRAFTSMAN®
is a registered trademark of Stanley Black & Decker, Inc., used under license.
es una marca registrada de Stanley Black & Decker, Inc., utilizada bajo licencio.
est une marque déposée de Stanley Black & Decker, Inc., utilisée sous licence.
2019 CRAFTSMAN
Product Manufactured by: EMERSON TOOL COMPANY
Producto fabricado por: 8100 W. Florissant • St. Louis, MO 63136
Produit fabriqué par : U.S. & Canada Only • É.-U. et Canada seulement
c
SP7088-2 CMXEVBE175850.indb 35 10/24/19 11:59 AM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Crafstman CMXEVBE17585 User manual

Category
Vacuum cleaners
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI